Gurney襟翼对翼型气动特性影响的风洞实验研究

针对风力机叶片翼型WA251A在Re=3.0×106情况下,安装Gurney襟翼时气动力的变化展开风洞实验研究.对WA251A翼型在干净翼和安装Gurney襟翼情形下的气动力进行对比,重点讨论了Gurney襟翼安装高度、安装角度及安装位置等因素对翼型气动力的影响.实验结果表明:同一安装位置安装高度的增加其增升效应越明显...     

电控旋翼直升机飞行动力学建模与配平特性研究

首先基于Peters He广义动态尾迹理论,建立了电控旋翼动态尾迹入流模型,进一步结合电控旋翼襟翼操纵与桨叶变距之间的关系、桨叶挥舞运动方程和带襟翼翼型非定常气动力模型建立了适用于飞行力学分析的电控旋翼气动力模型.在此基础上,结合机身、尾桨、尾面的气动力模型,建立了完整的电控旋翼直升机飞行动力学分析模型.以Z-11直升机为基准改造为电控旋翼直升机作为算例,计算了前飞状态下电控旋翼直升机的诱导速度分布和桨盘迎角分布,对比了电控旋翼与常规旋翼的气动特性差异;在此基础上,进一步分析了电控旋翼直升机的配平特性随前飞速度的变化规律以及与常规直升机的差异.     

电控旋翼气动特性建模与风洞试验验证

首先建立了带襟翼翼型的非定常气动力模型,继而基于Peters-He广义动态尾迹理论,考虑襟翼偏转对电控旋翼叶素环境的影响,建立了电控旋翼有限状态尾迹模型;进一步基于Theodorsen理论推导出电控旋翼桨叶挥舞响应与桨叶变距和襟翼操纵量的关系,综合以上建立了电控旋翼气动特性分析模型.以改进型电控旋翼试验系统为平台进行了风洞试验,测量了不同风速、不同襟翼操纵条件下的电控旋翼气动力、桨距、襟翼偏角及旋翼挥舞角的变化情况.理论计算结果与试验数据符合情况良好,验证了所建立的分析模型的正确性,并得出以下结论:旋翼转速一定时,桨叶变距与襟翼操纵基本呈线性关系;旋翼拉力随襟翼总距的增加而逐渐减小,襟翼总距较大时,其实际气动效率略有下降;前飞状态时,襟翼总距操纵会引起桨叶的纵向周期变距.      

加装格尼襟翼的旋翼机配平及稳定性研究

以某型自转旋翼机为对象,研究了格尼襟翼对自转旋翼机飞行动力学特性的影响。通过数值计算得到自转旋翼二维翼型加装格尼襟翼的气动力系数,采用叶素理论并结合动态入流理论建立自转旋翼动力学模型,在此基础上建立了旋翼机加装格尼襟翼的飞行动力学模型。研究表明,格尼襟翼对自转旋翼机的纵向配平特性有较大影响,纵向周期变距操纵量增大,旋翼稳定转速减小;格尼襟翼基本不影响全机稳定性,同时还能够达到减小功率消耗的效果。     

超临界翼型Gurney襟翼增升技术实验研究

通过在二元翼型风洞中进行测力实验,研究了不同高度Gurney襟翼对超临界翼型气动力和力矩的影响规律。实验结果表明：在亚声速条件下,Gurney襟翼同样可以明显增加翼型的升力系数,使整个升力曲线向上平移,并使翼型低头力矩增加。高度为翼型弦长0.5%的Gurney襟翼可以带来超临界翼型的最大升阻比。同Gur-ney襟翼对NACA 0012翼型气动特性改变的对比表明,其在超临界翼型上带来的升力系数增量要大于在NACA0012翼型上的效果,但是带来的低头力矩增量较小。     

Gurney襟翼改善翼型动态失速特性研究

采用CFD数值方法,研究了NACA0012翼型、加装传统Gurney襟翼及改进不对称Gurney襟翼后翼型的动态失速特性。给出了传统襟翼对翼型动态失速特性的影响,并带来较大动态低头力矩的不足,基于传统襟翼的不足,提出了改进的不对称Gurney襟翼方案。研究表明,不对称Gurney襟翼可较好改善翼型的动态失速特性,在增加动态升力的同时,俯仰低头力矩明显减小,可能是直升机旋翼的较理想翼型。     

后缘襟翼对直升机旋翼翼型动态失速特性的影响

 针对带后缘襟翼的智能旋翼直升机典型襟翼参数对翼型动态失速特性的影响进行了研究。建立了带后缘襟翼的桨叶动态失速模型,考虑了襟翼与桨叶之间的缝隙和襟翼在运动过程中相对桨叶的凸起,采用计算流体力学(CFD)方法,研究了不同襟翼转轴位置和襟翼与桨叶的缝隙情况下的翼型动态失速特性,探讨了后缘襟翼激励幅值、时长和起始时刻对升力和俯仰力矩系数的影响。研究结果表明:后缘襟翼能够较好地改善翼型动态失速时的气流环境,并减缓动态失速发生;襟翼激励最优幅值在25°附近,最优激励范围在方位角为240°~360°之间;襟翼转轴后移导致襟翼运动时产生的凸起会使襟翼控制效果减弱;襟翼与桨叶的缝隙会影响翼型动态失速特性,但是缝隙的长度(弦长的2%以内)对襟翼控制效果的影响很小。     

用于电控旋翼的带襟翼翼型关键参数研究

为满足电控旋翼的设计需要,首先给出了可计及襟翼移轴补偿影响的带襟翼翼型的综合时域非定常气动力计算模型.以此为基础,对襟翼弦长比和移轴补偿率这两个重要参数进行了分析.结果表明:增大移轴补偿率会减小升力系数;俯仰力矩系数随襟翼弦长比增大将出现最值,该最值与移轴补偿率有关;襟翼铰链力矩系数随襟翼弦长比增加迅速增大,而增加移轴补偿率则可大幅度减少襟翼铰链力矩系数.对于电控旋翼而言,襟翼弦长比取0.2左右,移轴补偿取0.25左右,可以取得较为满意的效果.     

尾缘襟翼长度对风力机翼型气动性能的影响

针对尾缘襟翼长度对风力机翼型气动性能的影响,分别以S809翼型与DU翼型为研究对象,设计了6种襟翼长度的襟翼模型,襟翼向翼型压力面偏转角为10°,襟翼与翼型主体之间为均匀1mm间隙,利用AUTOCAD对各襟翼长度模型进行几何建模。采用计算流体力学软件Fluent 14.0对各襟翼模型进行不同攻角下的气动性能计算,对翼型边界附近流场及压力系数等进行了分析比较。结果表明:尾缘襟翼长度对翼型的气动性能有较大的影响,襟翼长度不仅对襟翼附近的流场产生影响,对整个翼型的流场都有较大影响;带襟翼模型升力系数比无襟翼模型大大提高,且在一定攻角范围内随着襟翼长度增加,升力系数逐渐增大;带襟翼模型阻力系数比无襟翼模型翼型大,且在一定攻角范围内随襟翼长度增大阻力系数也增大;带襟翼模型升阻比在一定范围内比无襟翼模型大。     

旋转圆柱对翼型气动特性影响的数值模拟研究

采用数值模拟的方法研究了旋转圆柱对NACA0015翼型气动特性的影响,着重分析了前缘旋转圆柱转速比和缝隙大小对翼型升阻特性的作用规律以及不同安装位置的高速旋转圆柱结合简单襟翼偏转下的翼型气动力特性。结果表明,高速旋转的圆柱代替翼型前缘可以有效地抑制翼型背风区的流动分离,延缓边界层的发展从而改善翼型气动特性。前缘旋转圆柱理想的转速比在4附近,缝隙在2.5mm至1.5mm之间可以满足使用要求。简单襟翼结合前、后缘高速旋转圆柱情况下翼型的气动力特性可以比拟精心设计的多段翼型。旋转圆柱具有增升减阻效果显著,需要主动输入的能量极少等优点,是一种具有良好应用前景的边界层流动控制技术。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.