BT16钛合金渗氢压缩试样中的剪切带

为了深入了解渗氢及变形速率对BT16钛合金冷镦性能的影响,采用光学显微镜(OM)和显微硬度的方法,研究了BT16钛合金渗氢压缩试样中的剪切带。结果表明：在300 mm/s的压缩速率下,中心区变形流线与剪切带保持平行;在75 mm/s的压缩速率下,剪切带中心区与剪切变形过渡区边界模糊,变形流线与剪切带呈一定的小角度。在300 mm/s的压缩速率下形成的剪切带中心区显微硬度值近似为常数,且低于基体硬度值,剪切带中心区与基体之间存在一个硬度值线性增加的过渡区。对剪切带形成过程进行了分析,提出了利用变形流线计算剪切带最大应变的方法。     

BT16钛合金渗氢压缩试样中的剪切带

为了深入了解渗氢及变形速率对BT16钛合金冷镦性能的影响,采用光学显微镜(OM)和显微硬度的方法,研究了BT16钛合金渗氢压缩试样中的剪切带.结果表明:在300 mm/s的压缩速率下,中心区变形流线与剪切带保持平行;在75 mm/s的压缩速率下,剪切带中心区与剪切变形过渡区边界模糊,变形流线与剪切带呈一定的小角度.在300 mm/s的压缩速率下形成的剪切带中心区显微硬度值近似为常数,且低于基体硬度值,剪切带中心区与基体之间存在一个硬度值线性增加的过渡区.对剪切带形成过程进行了分析,提出了利用变形流线计算剪切带最大应变的方法.     

弹载主被动复合雷达天线配置方案

针对弹载雷达发展需求,探讨了实现弹载主被动复合雷达天线的技术途径。针对双频反射面天线,提出了一种双频反射面天线的配置方案;针对宽带复合天线,研究了被动模式宽带天线的选型和主动模式天线的设计方案,提出了宽带复合天线的配置方案。     

Frequency-hopping signal detection using partial band coverage

The performance of a channelized radiometer in detecting a frequency-hopping signal is analyzed for a variable number of parallel radiometers not necessarily covering the entire hopping band. The full band may not be covered because of an attempt to avoid interfering signals, limited radiometer resources, lack of knowledge of the band frequency location, or combinations of these factors. The analysis provides for calculation of the value of the signal-to-noise ratio (SNR) required to achieve a given probability of detection for a specified false-alarm rate, assuming an observation interval equivalent to N hops using either a fixed or a moving observation window. The dependence of the probability of detection on a misalignment of the detector observation intervals with the hop transitions is also analyzed. Numerical results are presented and discussed. Applied to a typical slow-hopping VHF radio, the results imply that a 150-hop transmission can be detected by a channelized radiometer covering half the hopping band when the SNR is about 2 dB     

InAsP cells for solar thermophotovoltaic applications

High temperature wide band gap InAsP cells have been specifically designed and fabricated for operating temperatures up 250°C to match with selective emitters operating near 1 μm in a TPV system. An important assumption is that the emitters can be heated up to the range of 1400 K to 2000 K by either solar concentrators or some other heat source. The efficiency of a selective emitter, which can be selected depending on the emitter operating temperatures, will be significantly higher than either a blackbody or a graybody emitter. The key for the TPV success is that the match between the band gap and selective emission must occur at the cell operating temperature. An appropriate cell band gap needs to be carefully selected; so when the band gap shrinks at the operating temperature, the desired match can be achieved. In this paper, two types of InAsP cells were investigated for this concept. The performance of these cells at elevated temperature and energy conversion efficiency are reported in this paper     

Adaptive sensitive frequency band selection for VMD to identify defective components of an axial piston pump

The underlying study investigates single valued neutrosophic entropy based adaptive sensitive frequency band selection for variational mode decomposition(VMD) for the purpose of identifying defective components in an axial pump. The proposed methodology is applied in the following steps. First, VMD is applied for decomposing vibration signals into various frequency bands, called as modes. After computing energy of each VMD, the lower(minimum) and upper(maximum) bounds from these energy readings ...     

数字闭环光纤陀螺死区机理研究与抑制

在数字闭环光纤陀螺中,死区产生及其附近噪声特性恶化的主要因素可以归结于施加在相位调制器上信号的串扰。根据死区产生机理的不同,提出了偏置相位调制和阶梯波反馈调制两种死区串扰误差因素的观点。通过对这两种死区误差机理的分析和比较,提出了采用模拟相加反馈方案可以避免偏置相位调制死区误差的观点。采用速率转台法测试了光纤陀螺的死区特性,验证了理论仿真和计算的正确性。最后,通过采用三角波相位抖动抑制死区误差技术,将一种高精度光纤陀螺0.08(°)/h的死区误差抑制到0.001(°)/h以下。     

Ten questions on UWB [ultra wide band radar]

Most radars now in use are narrow band systems with frequency bands much less than the carrier frequency. The theory and practice of current radar systems are based of this specific feature. But as is known, it is the frequency band that determines the information content of radar systems, as the volume of information transmitted per time unit is directly proportional to the frequency band. To raise the information capability of a radar system, the widening of its frequency band is needed. The only alternative approach is an increase in information transmission time. The actuality of this problem has determined rapid development in the last years of technologies using ultra wide band (UWB) signals. This paper describes the principles and features of UWB radar.     

14.5-14.8 GHz Frequency Sharing by Data Relay Satellite Uplinks and Broadcasting-Satellite Uplinks

Data relay satellites are being developed to provide real-time data links between research satellites in low earth orbits and central data acquisition and processing facilities. Frequency assignments for data relay satellite links will be made in bands allocated internationally to the space research service. One of the bands which will be used lies between 14.5 and 15.35 GHz, where the space research service has had a frequency allocation as a secondary service since 1971. During the General World Administrative Radio Conference of the International Telecommunication Union, held in Geneva in 1979, a primary frequency allocation was made in the band 14.5-14.8 GHz to the fixed-satellite service, specifically for use by earth-to-space links of the broadcasting satellite service. The feasibility of shared band operation is evaluated between data relay satellite uplinks and broadcasting-satellite feeder links in the band 14.5-14.8 GHz. Relationships for predicting interference power levels are formulated, as functions of satellite separation and of earth station separation. Tradeoffs between satellite separation angle and earth station separation are explored, and conclusions are drawn regarding the feasibility of band sharing. Co-channel operation is demonstrated to be technically feasible for typical systems, provided appropriate separations are maintained.     

镜面蒙皮拉形工艺参数研究

滑移带是导致飞机镜面蒙皮报废的主要原因之一。通过分析镜面蒙皮拉形中变形程度、拉形速度、毛料几何尺寸、润滑与操作方式对滑移带的影响,确定了临界变形程度和拉形应变速率的合理范围。毛料几何尺寸的影响,反映在悬空段板料的宽长比值上,宽长比值增加,变形趋向于平面应变状态,易出现滑移带。良好的润滑方式有利于改善板料变形的均匀性,增加成形面内材料的变形程度。操作方式的选择,应充分考虑模具拉胀的作用,严格控制夹钳预拉量和补拉量,避免冲击和阶跃式的加载方式。     

电磁波在等离子体高温气体中传输特性实验研究

针对高超声速飞行器头身部形成的等离子体鞘套对通信的影响,在中国空气动力研究与发展中心的粉末激波管上开展了电磁波在等离子体高温气体中传输特性的实验研究。实验中获得了等离子体气体中的电磁波透射率、电子密度和碰撞频率。实验结果表明：X波段和Ka波段电磁波在高激波马赫数Mas=16.1、1区气体压力P1=1200Pa的激波管实验状态下产生的厚度80mm等离子体高温气体中能量衰减大于30dB,难以传输;X和Ka波段电磁波在激波马赫数Mas=15.9、1区气体压力P1=80Pa的激波管实验状态下产生的厚度80mm等离子体高温气体中能量衰减大于30dB,难以传输;X波段和Ka波段电磁波在激波马赫数Mas=10.1、1区气体压力P1=80Pa的激波管实验状态下产生的高温等离子气体中平均传输损耗较小,可以进行有效传输;Ka波段电磁波在激波马赫数Mas=8.9、1区气体压力P1=1200Pa的激波管实验状态下产生的厚度80mm等离子体气体中平均传输损耗小于1dB,可以进行有效传输。实验得到的等离子体高温气体中的电磁波透射率、电子密度和碰撞频率与理论计算值基本一致。     

限带白噪声过程雨流幅值分布

为了在频域内解决限带白噪声载荷作用下结构的疲劳寿命估算问题,提出了限带白噪声过程的雨流幅值分布模型,并给出了参数估算方法。假设雨流幅值可以用双参数Weibull分布来描述,形状参数与带宽系数呈线性关系;尺度参数与均方根呈比例关系;比例因子与不规则因子呈线性关系。数值模拟结果表明：Weibull分布能够很好地描述限带白噪声过程的雨流幅值分布,分布参数能够根据随机过程的谱参数计算得出。     

The cepheid luminosity scale

Conclusions The discrepancy between the luminosity scale for Cepheids derived from the intermediate band photometry and the presently accepted scale requires further investigation. We have discussed various factors which might affect the previous work and which might affect the present method but we are unable at this time to provide a definite explanation. However, since there is no obvious problem with the intermediate band photometry we should give serious consideration to the possibility that the Cepheid luminosity scale might require some revision.     

A model-scale test on noise from single-stream nozzle exhaust geometries in static conditions

A model-scale test with single-stream nozzle exhaust geometries was carried out at the anechoic chamber of Beihang University in Beijing, China. The spectral characteristics are investigated, and the effects of the following parametric variations are reported in this paper: impact of nozzle operating conditions on spectra; impact of the presence of a plug; and effectiveness of chevron configurations for noise mitigation. The measurement shows that the change of pressure values has more impact on spectra than the change of temperature values. The spectral change due to pressure is shown at all band numbers for unheated conditions whereas it is more pronounced at high-frequency ranges for heated conditions. An impact of the presence of a plug is also clearly observed. The reduction of noise is moderate up to band number of 35, and becomes more significant at higher band numbers. It is observed that chevron nozzles are more efficient at high pressure and temperature values. It is expected that the quantified analysis will be used to develop an empirical model of single jet noise, which will be the baseline for the development of prediction of noise from turbofan engines of high bypass ratios.     

一种基于预测和变换混合设计的超光谱图像压缩方法

提出了一种新的超光谱图像压缩方法。该方法针对三维小波压缩编码方法对专有数据的特殊属性利用效率较低的缺陷,设计了一种应用于超光谱图像的预测编码和变换编码相混合的实现方案。首先,由超光谱图像的高谱间相关性,推导出图像各波段间的一般表达式。然后,根据这一表达式建立了超光谱图像的波段预测方式。该预测方式以波段为单位,参考波段采用小波变换编码技术进行压缩。为了提高预测的精度,参考波段选择器和波段预测器分别基于超光谱图像的数学统计规律和各波段直方图形状相似的特性进行设计。最后,将预测偏差值通过三维小波编码技术进行压缩。实验结果表明,本文设计的方法与目前先进的超光谱压缩技术相比能够提供具有竞争力的性能提升,且具有良好的兼容性、灵活性和渐进传输能力。     

制定飞机结构声疲劳载荷谱的方法研究

介绍了现用的制定声载荷谱的方法,并在使用状态时间进行归纳的过程中解决了针对倍频程或１／３倍频程声压级分析结果进行归纳的具体方法。按这一方法归纳的声疲劳载荷谱及其软件已成功地用于声疲劳试验     

基于声发射信号的高速铣削过程监测技术

叙述了如何将声发射技术应用于航空铝合金的高速铣削过程监测,介绍了监测装置硬件系统和信号数据采集平台的构成,最后运用小波分析进行信号分解,计算分解后的各频段能量,并从频段的能量对比中发现,信号能量可以作为刀具磨损的特征参数.     

Correlation Function for a 1/f Spectrum

The performance of ground surveillance radars depends on the spatial correlation, or spectrum, of the radar returns. Many radar terrain images are suspected to have a I/f spatial spectrum. This spectrum is thought to be difficult to handle mathematically in modeling and analysis because of its singularity at zero frequency and its infinite energy. A two-dimensional, band-limited I/f spectrum has neither of these problems: this is convenient for modeling and analysis in any practical system because the sensor measuring of an image always introduces band limiting, even if the natural phenomena are not band limited. Also shows the presence of terrain with a 1/f spectrum will not be readily apparent from the correlation function of the terrain image because the shape of the correlation function is largely determined by the sensor band limit and not by the underlying spectrum.     

应用计算机绘图研制螺旋天线

本文介绍的是为有源雷达回波增强器研制的阿基米德平面螺旋和等角平面螺旋天线,并给出方向性图,电压驻波比和圆极化等电参数从S波段到X波段的测试结果。 在研制过程中用SKG语言（配DJ-052微机和绘图仪）进行编程并自动画出各种天线的精确形状,它捂言简练,工效很高。     

微波在薄层等离子体中传输效应研究

为了准确预测再入飞行过程中等离子体对微波传输特性的影响,采用WKB方法、FDTD方法、平面波理论和薄层等离子体理论4种方法,结合粉末激波管上开展的试验研究了X波段和Ka波段微波在薄层等离子体中的传输效应。对于X波段,试验时激波马赫数为9.6、10.7和10.5;对于Ka波段,试验时激波马赫数为10.5。通过对比与分析获得的主要结论有：当等离子体厚度和入射波波长相近时,薄层等离子体理论计算结果比其它三种方法的计算结果更接近于试验结果;在碰撞频率接近并且电子密度小于临界电子密度的条件下,Ka波段微波信号穿过相同厚度的等离子体比X波段微波信号衰减小得多,具有更强的穿透性;如果等离子体碰撞频率和微波入射频率相同,随着电子密度的增加,微波信号穿过相同厚度的等离子体时衰减变大;当碰撞频率和入射波频率差不多时,共振吸收导致衰减达到最大值。