Optimum FFT-based frequency acquisition with application toCOSPAS-SARSAT

In the case of a single sinusoid or multiple well-separated sinusoids, a coarse estimator consisting of a windowed Fourier transform followed by a fine estimator which is an interpolator is a good approximation to an optimal frequency acquisition and measurement algorithm. The design tradeoffs are described. It is shown that for the fine-frequency estimator a good method is to fit a Gaussian function to the fast-Fourier-transform (FFT) peak and its two neighbors. This method achieves a frequency standard deviation and a bias in the order of only a few percent of a bin. In the case of short-time stationarity, for a moderate number of averages and for an adaptive threshold detector, only between 0.5 and 1 dB is lost when averaging is traded off for FFT length, in contrast to the asymptotic result of 1.5 dB. The COSPAS-SARSAT satellite system for emergency detection and localization is used to illustrate the concepts. The algorithm is analyzed theoretically, and good agreement is found with test results     

Interference torque of a three-floated gyroscope with gas-lubricated bearings subject to a sudden change of the specific force

A numerical study is carried out to investigate the influence of a sudden change of the specific force on a three-floated gyroscope with a rotor supported on gas-lubricated bearings.The interference torque is calculated to evaluate the influence by modeling the transient behavior of the rotor-bearing system. In combination with dynamic equations of the rotor displacement,the Reynolds equation is solved on the surface of spiral-grooved conical bearings. It is assumed that a steady state has been obtained with a constant specific force, and then the specific force is suddenly changed and maintained constant after that. Responses of the sudden change are obtained by solving the equations. Numerical results show that the direction of the sudden change of the specific force is the main factor which influences the interference torque curve. With a sudden change along the input direction, the interference torque fluctuation has a constant frequency and a decreasing amplitude. With a sudden change along the output direction, the interference torque fluctuates in a small range. With a sudden change along the spin direction, the change of the interference torque combines a fluctuation and a gradually-changing quasi-equilibrium value. This study provides a supplement to the steady-state error model of the three-floated gyroscope.     

液体冲压发动机控制系统半实物仿真

运用小偏离线性化理论和Willoh方法，建立了液体冲压发动机和弹体动态数学模型。动态数学模型在微型计算上一体化运行，形成液体冲压发动机／弹体一体化实时数字仿真器。实时数字仿真器通过输入输出接口与液体冲压发动机的实际控制系统进行联接，组成液体冲压发动机、弹性和发动机控制系统半实物仿真系统。对冲压发动机飞行马赫数和控制 系统供油量的半实物仿真结果表明，系统能满足研制工作的需要。     

Simulation on effect of throat contraction ratio and strake stagger angle on flow field and aerodynamic performance of scrampressor

The design methods of typical supersonic aircraft intakes and shock wave compression technology have been applied to ram-rotor, an attractive compression system. A ram-rotor is of a typical structure including the compression ramp, the throat and the subsonic diffuser; a scrampressor is similar to ram-rotor, the only difference is that scrampressor has no subsonic diffuser. The work was the continuation of the preparatory work. In order to further study the effect of throat contraction ratio and strake stagger angle on the flow field and performance of a scrampressor, the flow field of a scrampressor with a three-dimensional flow path was numerically simulated with different throat contraction ratios and strake stagger angles. Simulated results indicated that the optional aerodynamic performance of a scrampressor could be achieved with an adiabatic efficiency of 0.8413 a total pressure recovery coefficient of 0.8446, a total pressure ratio of 7.14 and a static pressure ratio of 5.17 for a throat contraction ratio of 0.6 and a strake stagger angle of 12°. It was therefore concluded that an appropriate decrease in throat contraction ratio and an increase in strake stagger angle could help the comprehensive improvement of a scrampressor in performance.      

A comparative study on acoustic damping induced by half-wave, quarter-wave, and Helmholtz resonators

The damping characteristics of three-type resonators, a half-wave, a quarter-wave, and a Helmholtz resonator are studied experimentally by adopting linear acoustic test. A quantitative acoustic property of sound absorption coefficient in a model enclosure with the resonators is measured and thereby, the acoustic-damping capacity of a resonator is characterized. For a comparative study on acoustic damping, the damping capacity of a half-wave resonator is compared with that of the other resonators. A half-wave and a quarter-wave resonators have the same damping mechanism, but a quarter-wave resonator has much larger damping capacity than a half-wave resonator with the same diameter of a single resonator. It is found that shorter length of a resonator has the advantage of longer one with respect to the damping capacity. The damping capacity of a Helmholtz resonator increases with cavity volume and does as the orifice length decreases. A Helmholtz resonator has the highest damping capacity of three-type resonators and a half-wave resonator has the lowest. Besides, a Helmholtz resonator requires the smallest number of resonators for optimal damping. The design criterion of each resonator on the optimal damping is provided by the normalized parameter of open-area ratio and the similarity behavior for the optimal damping is observed for various enclosure diameters.     

Dynamics and de-spin control of massive target by single tethered space tug

This paper investigates the dynamics and de-spin control of a massive target by a single tethered space tug in the post-capture phase. The dynamic model of the tethered system is derived and simplified to a dimensionless form. Further, a decoupled PD controller is proposed, and the local stability of the controller is analyzed by linearization technique. Parametric studies of the dynamics and de-spin control of a massive target are conducted to characterize the dynamic process of de-spin with the proposed control law. It is shown that the massive target can be de-span by a single and small space tug with limited thrust within finite time. The thrust tangent with the tether de-spins the target while the thrust normal to the tether prevents the tether from winding up the target. The tether length has a positive contribution to the de-spin of a target. The longer tether leads to a faster de-spin process.     

Measurement of Distributed Targets with the Random Signal Radar

A model of a distributed target as a collection of independent, Poisson distributed point scatterers or scattering centers in a range-velocity target space is introduced and is characterized by a deterministic function called the ?scatterer density function.? This function is the density of the point scatterers in the range-velocity space and can be estimated in a relatively straightforward manner by any radar having adequate resolution in both range and velocity and no ambiguities in the region occupied by the distributed target. The use of the random signal radar with a correlator receiver is considered here and the statistical properties of the correlator output, when the return signal is from a distributed target, are derived. It is shown that the spectral density is simply related to the scatterer density function. The technique is illustrated by an example in which the target is a tornado modeled as a cylinder with constant angular velocity. The example suggests that is a possible to remotely estimate the radar cross section per unit volume as a function of distance from the center of the tornado.     

基于普通分离原理的制导/估计综合设计方法

现有的先进制导律研究常常分离设计最优估计器和最优制导律,但是这种分离设计没有被证明是有效和最优的设计方法.本文基于普通分离原理(GST),提出一种制导/估计综合设计方法.首先,将拦截器反导作战模型考虑为一类非线性、非高斯追逃拦截问题,建立了噪声环境中追逐-逃逸对策模型;其次,引入追逃未达集概念,利用几何方法将估计器设计...     

Detection of chi-square fluctuating targets in arbitrary clutter

In a recent paper, general expressions were derived for the density and cumulative probability functions of the amplitude of a linear matched-filter output given a nonfluctuating target in a clutter-limited environment. These expressions were based on the clutter amplitude density function. The results are extended to calculate the cumulative probability function of the output of a linear matched filter used to detect a chi-square fluctuating target in a clutter-limited environment. The resulting method is applied to a common radar clutter model, and experimental sonar data.     

二元非线性机翼随机动力学行为

 为考查在高斯白噪声作用下二元机翼随机颤振动力学行为,采用数值仿真的方法对其进行了研究。首先把机翼简化成一个具有扭转和上下自由度的平板,其中扭转弹簧具有3次非线性刚度,同时假设空气是线性不可压的而且气动力是定常的,再对任意运动和高斯白噪声作用下的机翼进行建模。其次采用了蒙特卡罗仿真来求解随机微分方程的数值解,根据数值解结果进行统计分析,计算出最大Lyapunov指数。最后得出：在随机激励作用下机翼的动力学行为与确定性颤振相比有很大差异,同时随机颤振点提前于确定性颤振点。     

直升机燃油系统地面模拟试验中试验台转角与油面角的关系

为了在直升机燃油系统地面模拟试验中准确地模拟油面角，本文介绍了试验台转角与油面角的关系，并给出了转换结果，同时，提出了一种用油箱内增压来模拟过载的设想，使在模拟试验时，油泵供油更趋真实，通过简化计算，给出了确定气压力的方法和判断依据。     

基于数据模型的某型民用飞机货舱区域腐蚀影响因素研究

 为研究舱内环境因素对民用飞机货舱区域腐蚀的影响,采集了停场飞机的货舱内外环境指标的数据,建立线性模型,给出了飞机货舱内外环境指标的数量关系。收集了国内几家航空公司某型民用飞机长期的结构腐蚀维修数据,计算了飞机货舱区域腐蚀频率与环境因素的灰色关联度,选取影响腐蚀的主要环境因素,提取主成分消除环境因素之间的多重共线性,建立腐蚀频率的多因素回归模型,研究了各类环境因素对飞机货舱区域腐蚀的影响规律与特点。分析结果表明:高温高湿天数与降水指标对该型飞机货舱区域腐蚀有显著的促进作用,并且不同航空公司的货舱区域腐蚀频率有显著差异,表明运营、结构检查和维护等人为因素对货舱区域腐蚀有显著影响。分析结果符合民用飞机货舱腐蚀控制的工程经验,表明研究方法是合理的。     

隐身外形飞行器用埋入式进气道的设计与风洞实验研究

本文为隐身外形飞行器用埋入式进气道发展了一套设计方法。该方法的理论基础是埋入式进气道进气机理和气动S弯概念,其关键技术包含通道中心线设计、横截面面积变化规律设计以及横截面形状设计等,各技术可以方便地用数学方法加以描述,整个方法易于编程实现。并结合一种隐身外形无人机提出了埋入式进气道方案,通过实验得到了此类隐身外形飞行器用埋入式进气道的气动特性。结果表明,所提出的埋入式进气道方案可行,所设计的模型进气道性能良好,所发展的设计方法合理。同时验证了埋入式进气道进气机理的正确性,也表明隐身外形飞行器与埋入式进气道的组合方案具有十分光明的应用前景。     

雷击建筑物时防雷系统中雷电流的分布研究

主要讨论雷直击建筑物时雷电流在防雷系统中的分布特性，介绍利用计算机进行数值计算的方法。通过典型算例、传统的电磁暂态计算程序——EMTP的计算结果和利用清华大学高压实验室的冲击大电流发生装置，对此结构模型进行模拟试验，将3种结果进行比较，从而验证了本研究所编制的计算机程序的正确性。为进一步研究室内电磁场的暂态分析做好基础。     

Asymptotic Reproducibility in Nonlinear Systems and Attitude Control of Gyrostat

A control law is presented for asymptotic function reproducibility in a class of nonlinear-systems such that the output of the system asympotically tends to a given function. The controller consists of a prefilter and a servocompensator. Based on this result, a nonlinear feedback control law for the attitude control of a satellite containing symmetric rotors, in a circular orbit, is derived. In the closed-loop system, given trajectories of pitch, yaw, and roll angles are asymptotically followed, and set point control of attitude is accomplished. Digital simulation results are presented to show the capability of the nonlinear controller.     

导弹运动方程的逆解析解

针对在采用反馈线性化理论设计导弹飞行控制系统时控制器算法对导弹逆模型的要求 ,推导了导弹运动方程的逆解析解 ,包括导弹质心运动的运动学方程及其动力学方程的逆解析解、姿态运动的运动学方程及其动力学方程的逆解析解 ,详细给出了逆模型的求解过程 ,为一类飞行控制系统运用全局线性化设计奠定了基础。最后 ,结合工程应用进行了仿真计算 ,仿真结果表明逆解析解的推导是正确的     

An automated approach to calculating the maximum diameters of multiple cutters and their paths for sectional milling of centrifugal impellers on a 4?-axis CNC machine

Power generators and chemical engineering compressors include heavy and large centrifugal impellers. To produce these impellers in high-speed machining, a 4?-axis milling machine(or a 4-axis machine plus an indexing table) is often used in the industry, which is more rigid than a5-axis milling machine. Since impeller blades are designed with complex B-spline surfaces and impeller channels spaces vary significantly, it is more efficient to use multiple cutters as large as possible to cut a channel in sections and a blade surface in patches, instead of only using a small cutter to machine a whole blade and a channel. Unfortunately, no approach has been established to automatically calculate the largest diameters of cutters and their paths, which include the indexing table angles. To address this problem, an automated and optimization approach is proposed. Based on the structure of a 4?-axis machine, a geometric model for a cutter gouging/interfering the impeller is formulated, and an optimization model of the cutter diameter in terms of the indexing table angle is established at a cutter contact(CC) point on a blade surface. Then, the diameters of the tools,their orientations, and the indexing table angles are optimized, and each tool's paths are generated for machining its corresponding impeller section. As a test, an impeller is efficiently machined with these tools section by section; thus, this approach is valid. It can be directly used in the industry to improve efficiency of machining centrifugal impellers.     

前置不同诱导轮高速离心泵旋转空化特性研究

以高速诱导轮离心泵为研究对象,开展了无诱导轮、前置等螺距诱导轮、前置变螺距诱导轮及前置分流叶片诱导轮4种情况下离心泵全流道的空化数值模拟和汽蚀特性实验研究.通过外特性实验研究得到:在同一流量下,前置等螺距诱导轮离心泵的扬程最低,前置变螺距诱导轮离心泵的扬程次之,前置分流叶片诱导轮离心泵的扬程较两者稍高.通过汽蚀实验和数值模拟研究得到:在前置3种诱导轮的情况下,离心泵的汽蚀性能都得到了改善,其改善效果从低到高依次是:变螺距诱导轮、分流叶片诱导轮、等螺距诱导轮.通过对汽相体积分数分布情况的研究得到:诱导轮的吸力面除进口外缘容易发生汽蚀外,叶片出口靠近轮毂侧也较容易发生汽蚀;对比分析主叶轮和诱导轮的汽蚀情况,得到诱导轮汽蚀的严重性与离心叶轮的汽蚀严重性并非成正比的结论.     

五分量激光测量装置的试验研究

所讨论的激光测量装置,可以同时测量~个移动轴的5个移动误差分量,即两个直线度分量和3个角位移分量。该装置测量线性误差和角位移误差的精度可分别达到1.5μm和0.5”以内。     

带止口法兰连接结构刚度特性对结构振动影响

对带有止口的法兰连接结构刚度特性进行了数值仿真研究。使用有限元软件ANSYS分析了带有止口的法兰连接结构的迟滞特性。通过对止口接触面的变形-滑移机理分析,使用一个詹金斯单元和一个弹簧单元并联模拟法兰的一个扇区,并基于法兰弯曲变形时每个扇区的不同状态建立了整个法兰结构的弯曲刚度简化模型,并对该简化模型进行了仿真,该简化模型能够较准确地模拟带止口法兰连接结构的刚度特性。基于简化模型和梁单元建立了简化转子结构模型,分析了带有止口的法兰连接结构对转子稳态动力学响应的影响。结果表明带有止口的法兰连接结构的迟滞特性能够影响峰值频率,随着止口过盈量的增加,响应峰值显著降低,具有较好的振动抑制效果。