镍基耐高温自润滑刷式封严涂层研究

为满足先进航空发动机刷式封严对涂层材料自润滑耐磨性能的要求,采用等离子喷涂技术制备了NiCoCrAlY-Cr_2O_3和NiCoCrAlY-Cr_2O_3-AgMo两种复合涂层;采用扫描电子显微镜、X射线衍射、拉曼光谱和高温摩擦磨损试验等分析测试手段研究了涂层的物相组成、微观结构、力学性能以及摩擦磨损性能。结果表明:研制的两种新型涂层具有较低的孔隙率、较高的显微硬度和结合强度,从20℃到800℃的磨损量都在10~(-5)mm~3·N~(-1)·m~(-1)数量级,显示出优异的耐磨性能;NiCoCrAlY-Cr_2O_3涂层在摩擦系数随着温度的升高而降低,在800℃达到最低值0.3;NiCoCrAlY-Cr_2O_3-AgMo涂层从400~800℃的摩擦系数一直保持在0.23左右。对其摩擦机理的研究表明:400℃时涂层与高温合金GH4145对磨件之间形成连续的含Ag润滑膜,600℃以上时摩擦表面生成的Ag_2MoO_4自润滑相显著降低了涂层的摩擦和磨损。     

类金刚石薄膜的微/纳米机械和摩擦性能

采用真空磁过滤等离子电弧沉积的方法在9Crl8钢上沉积不同厚度的DLC膜。为了检测成膜质量，在较宽的载荷范围内分别使用显微硬度、纳米压痕和划痕技术表征9Crl8钢和DLC／9Crl8的机械和摩擦性能。结果显示，9Crl8和DLC的纳米硬度和弹性模量分别为8GPa、250GPa和60GPa、600GPa，9Crl8、DLC和有机膜的摩擦系数分别为0．35、0．20和0．13。纳米压痕和划痕技术能为DLC／9Crl8提供丰富的近表面弹塑性变形和摩擦、磨损等信息。DLC／9Crl8的机械和摩擦性能的研究可以用来评估膜的承载和抗磨损性能。     

离子束辅助沉积WS_2-Ti-Ag复合薄膜的摩擦性能

采用ZDH-100型号离子束复合沉积设备沉积WS_2-Ti-Ag复合薄膜,基材为轴承钢和单晶硅(100).采用场发射扫描电子显微镜、XRD衍射仪,检测复合薄膜的表面形貌、微观结构.采用球-盘式摩擦磨损试验机,对复合薄膜在大气环境中的摩擦性能进行了研究.结果表明:采用离子束辅助沉积技术制备的WS_2-Ti-Ag复合薄膜是非晶态薄膜;并且随法向载荷的增加,复合薄膜的摩擦因数减小,摩擦状态越稳定,耐磨寿命越短.     

原位合成TiC颗粒强化铝合金组织与性能

采用铝系合金2A14（LD10）作为母合金,利用原位合成法制备了TiC颗粒弥散强化铝基材料。显微组织观察表明,合金中的TiC颗粒呈等轴状,尺寸约为1～3μm。加入TiC颗粒后,合金铸态组织显著细化,室温抗拉强度和屈服强度得到一定程度提高,但塑性下降。150℃时,合金的拉伸性能变化随TiC加入量增加而变化的规律与室温相似。合金中TiC颗粒的引人大大提高了合金的耐磨性能。在油润滑条件下,TiC／2A14材料的耐磨损体积远远优于其母合金以及其他典型的金属耐磨材料,如耐磨黄铜、ZA30锌基合金和Al—30Si高硅铝合金。     

磁过滤直流真空阴极弧制备类金刚石膜的结构和力学性能研究

采用磁过滤直流真空阴极弧沉积技术在硅片、不锈钢片基体上制备了类金刚石(DLC)膜。检测结果表明,膜中存在着微米级的大颗粒分布,膜厚为290nm,sp3键的含量为62.23%。所制备的薄膜具有典型的DLC膜Raman光谱特征,耐磨性能优良,膜与基体的结合性能良好。     

真空中多孔氮化硅的高温弯曲强度

研究了高温真空环境下多孔(气孔率>50%)氯化硅陶瓷的弯曲强度,并进行了初步分析.结果表明,多孔氮化硅陶瓷在真空中的高温强度随温度上升而降低,由于没有氧化作用,晶界玻璃相在高温下的软化成为影响其强度的主要因素.     

石墨密封材料高温摩擦磨损行为及预测

利用HT-1000型高温摩擦磨损试验机研究了石墨M210密封材料高温下摩擦磨损性能,采用扫描电子显微镜（SEM）观察分析了磨损表面形貌.基于试验数据,通过灰色理论GM（1,1）建立了摩擦因数和磨损率预测模型.结果表明:石墨M210密封材料摩擦因数呈先增大再减小,而后趋于一稳定值,试验温度为450℃时,摩擦因数最小;磨损率随着试验温度升高而增大.试验温度在低于300℃,磨损表面具有明显的黏着、撕裂和无序的塑流动痕迹,高于400℃时,塑流动痕迹具有明显的方向性,出现了剥落和断裂痕迹.温度较低时,石墨材料表面主要是水汽物理吸附膜起润滑作用,随着试验温度升高,由物理吸附膜润滑逐渐转向反应膜润滑.基于试验数据建立了精度等级均为1级的摩擦因数和磨损率的预测模型.      

单体与交联剂比例对凝胶注模成型多孔氮化硅性能的影响

利用凝胶注模成型工艺,在固定单体交联荆总质量的情况下,改变单体与交联剂的质量比例,制备出不同单体与交联剂比例的多孔氮化硅陶瓷.借助扫描电子显微镜、Archimedes法和三点弯曲法等方法研究了单体与交联剂比例对多孔氮化硅陶瓷的微观结构和基本力学性能的影响.结果表明,随着单体与交联剂比例的增大,试样的干燥收缩率增大;当单体与交联剂比例≥15时,试样排胶后出现开裂现象;当单体与交联剂比例<15时,随着单体与交联剂比例增大,烧成后的试样强度呈增大的趋势.     

GH4169合金反挤压成形模具磨损

基于修正 Archard 磨损模型,采用数值模拟方法系统分析了 GH4169合金反挤压成形过程中各挤压工艺参数对模具磨损的影响规律。结果表明：在选取的参数范围内,挤压凸模最易产生磨损失效的区域为凸模圆角处,模具最大磨损深度随凸模圆角半径及坯料预热温度的增大而降低,随摩擦系数的增大而增大;当挤压速率小于100 mm ／s时,模具最大磨损深度随挤压速率的增大而减小,当挤压速率大于100mm ／s 时,模具最大磨损深度随挤压速率的增大先增大后减小。最佳工艺参数坯料预热温度1020℃,摩擦系数0．05,变形速率100mm ／s,模具预热温度300℃时模具磨损量最小,为9．28×10－3 mm。     

三种热喷涂工艺制备NiCr/Cr_3C_2-BaF_2·CaF_2涂层的结构与性能

采用大气等离子喷涂、爆炸喷涂和超音速火焰喷涂三种热喷涂技术制备了NiCr／Cr3C2-BaF2&#183;CaF2涂层,分析比较了涂层的显微组织、物相组成、孔隙率、硬度、结合强度及其摩擦学性能。结果表明,与大气等离子喷涂相比,超音速火焰喷涂和爆炸喷涂技术制备的涂层具有更高的致密度、硬度和结合强度。采用包覆法制备的粉末进行喷涂,碳化物失碳明显减少,涂层中氧化物含量低。三种NiCr／Cr3C2-BaF2&#183;CaF2热喷涂涂层的摩擦系数都随着温度的升高而减小,爆炸喷涂和超音速火焰喷涂涂层的摩擦系数比等离子喷涂涂层的摩擦系数更低,耐磨性得到提高。高温下BaF2&#183;CaF2润滑膜的形成均可有效降低三种涂层的摩擦系数,从而降低涂层和对磨球Si3N4的磨损率。     

镁合金AZ91表面弧辉等离子沉积TiN/CrN薄膜的摩擦行为研究

镁合金具有高的比强度、低的弹性模量、减震等优点,在航空航天领域具有很大的应用前景.但是低劣的耐磨性导致镁合金限制于制造静载零件.为改进其耐磨性,采用弧辉等离子沉积的新工艺在镁合金AZ91表面涂覆TiN/CrN多层薄膜.薄膜由12层TiN和CrN交替沉积而成,总厚度为2 μm.用扫描电镜(SEM)、X射线衍射(XRD)和辉光放电光谱(GDS)分析涂层的成分和微观结构.采用球盘磨损试验测试摩擦系数,并计算出比磨损率.结果表明,与未处理试样相比摩擦系数增大,但磨损率急剧下降.薄膜的表面硬度超过HK0.011433.     

Influences of pulse frequency on formation and properties of composite anodic oxide films on Ti-10V-2Fe-3Al alloy

A thick composite anodic oxide film was fabricated in an environmentally friendly malic acid electrolyte containing PolyTetraFluoroEthylene (PTFE) nanoparticles on Ti-10V-2Fe-3Al alloys. The influence of pulse frequency on the morphology, microstructure and composition of composite anodic oxide films containing PTFE nanoparticles was investigated using Field Emission Scanning Electron Microscopy (FE-SEM) equipped with Energy Dispersive Spectroscopy (EDS), Atomic Force Microscopy (AFM) and Raman spectroscopy. The tribological properties in terms of the friction coefficient, wear loss and morphology of worn surfaces were measured by ball-on-disc tests. The electrochemical property was evaluated by potentiodynamic polarization. The results indicated that the titanium dioxide of composite anodic oxide films transformed from anatase to rutile with the change of pulse frequency, which could result from the electrochemical dynamic equilibrium. The combination of PTFE nanoparticles and malic acid electrolyte molecules can influence the energy fluctuation of electrochemical equilibrium and formation of composite anodic oxide films. Moreover, composite anodic oxide films fabricated under the condition of 1.0–2.0 Hz exhibited the best wear resistance and corrosion property. The schematic diagram of the film formation and PTFE nanoparticles spreading process under different frequencies was elucidated.     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

并联硅基扩缩微通道热沉强化传热特性

采用去离子水作为冷却工质,实验研究了并联硅基扩缩微通道热沉内的流体流动与强化传热特性.基于微尺度强化传热机理,设计加工了两种并联硅基扩缩微通道热沉.通过测量流体的体积流量、进出口压降与温度、热沉底面加热膜温度,并以传统矩形直通道热沉为参照,获得了并联硅基扩缩微通道热沉在恒热流边界条件和不同体积流量工况下流体流动与对流传热特性参数.结果显示:相对于矩形直通道,并联硅基扩缩微通道热沉的表面传热系数可提高12.5%~85.1%,但摩擦因数只增加了-9.2%~31.4%.表明并联硅基扩缩微通道热沉具有优越的强化传热特性.      

航空煤油泵轴尾机械密封副材料特性

为选择适合在航空煤油介质中工作的机械密封副材料,对材料的摩擦特性进行了研究,利用摩擦磨损试验机得到不同工况条件与表面粗糙度下材料的摩擦因数、温升,在原子力显微镜(AFM)下对3组典型配对材料的微观磨损形貌进行观测,分析磨粒磨损和黏着磨损的行为差异,计算磨损的关键参数。研究发现:聚四氟乙烯（PTFE)在既定条件下为性能最佳的软材料;硬材料表面粗糙度值为0.05时的摩擦性能最佳,不同硬材料间性能差异不大。研究发现PTFE在配磨材料上产生的犁沟效应最轻微,黏附的元素颗粒最少;黏着磨损会造成表面高度分布函数的偏移,利用离散化求解公式得到了黏着体积与平均黏着厚度。      

磨削钛合金时砂轮磨损机理的研究

 磨削钛合金时砂轮磨损严重,磨削比很低。为了改善钛合金的磨削加工性,本文着重分析了造成砂轮磨损的主要原因,论述了粘附磨损、扩散磨损以及磨粒破碎、脱落所造成的磨损,并分析了磨削条件对砂轮磨损的影响。     

High-temperature tribological behaviors of a Cr-Si co-alloyed layer on TA15 alloy

A Cr-Si co-alloyed layer was successfully deposited on TA15 alloy by the double glow plasma surface technology to improve its poor wear resistance at elevated temperature.The microstructure,composition,and phase structure of the layer were investigated by SEM,EDS,and XRD.The tribological behaviors of the Cr-Si co-alloyed layer at 20 ℃ and 500 ℃ were analyzed in details.The results indicated that the friction coefficient and wear rate of the Cr-Si coalloyed layer at 20 ℃ and 500 ℃ were much lower than those of the substrate,which was due to higher hardness and superior elastic modulus.This layer may become an approach to effectively improving the wear resistance of TA15 alloy at elevated temperature.     

Characteristics of Disorder and Defect in Hydrogenated Amorphous Silicon Nitride Thin Films Containing Silicon Nanograins

The hydrogenated amorphous silicon nitride (SiNx) thin films embedded with nano-structural silicon were prepared and the micro-structures at the interface of silicon nano-grains/SiNx were identified by the optical absorption and Raman scattering measurements. Characterized by the exponential tail of optical absorption and the band-width of the Raman scattering TO mode, the disorder in the interface region increases with the gas flow ratio increasing. Besides, as reflected by the sub-gap absorption coefficients, the density of interface defect states decreases, which can be attributed to the structural mismatch in the interface region and also the changes of hy-drogen content in the deposited films. Additional annealing treatment results in a significant increase of defects and degree of disorder, for which the hydrogen out-diffusion in the annealing process would be responsible.     

用离子束辅助沉积(IBAD)工艺制备TiCxNy膜的研究

用离子束辅助沉积（ＩＢＡＤ）工艺在９Ｃｒ１８、ＧＣｒ１５钢基体上形成了ＴｉＣｘＮｙ膜。ＴＥＭ观察发现膜均呈多晶结构,都具有（１１１）、（２００）和（２２０）择优取向。ＡＥＳ和ＸＰＳ分析进一步证实,ＴｉＣｘＮｙ膜呈含氧配置。干摩擦表明膜的抗氧化性能优良,其存在能有效抑制基体在摩擦过程中氧化膜的形成。又由于膜的硬度高,润滑性良好,每种基体的磨损特性都得到了显著地改善。但随着基体不同,膜的力学机械性能随     

IBAD法沉积TiN薄膜的机械和耐腐性

用离子束辅助沉积(IBAD)方法在医用不锈钢317L基底上沉积TiN陶瓷薄膜。通过X射线衍射(XRD)和俄歇电子能谱(AES)分析研究了薄膜的微结构；测试了薄膜的耐磨性及薄膜与基底的附着力：运用电化学腐蚀的方法检测了薄膜在Hank’s模拟体液中的耐腐蚀性能。研究结果表明：用高、低能氮离子束兼用的IBAD方法沉积TiN多晶薄膜后，材料表面结构和性能发生明显改变。表面硬度和耐磨性有明显提高，在Hank’s模拟体液中显示出更强的抗腐蚀能力。