双冷速缓冷处理对P／M Rene‘95合金等温变形的影响

研究了双冷速缓冷处理对Ｐ／ＭＲｅｎｅ’９５合金等温变形的影响。研究结果表明：双冷速缓冷处理可有效地控制合金中γ＇相的析出，尤其可通过第二冷速控制γ＇相的形态。当固溶温度为１１００Ｃ时，第二冷速低于第一冷速有利于降低合金的流变应力。     

粉末高温合金超塑性等温锻造技术研究

对FGH96合金超塑性及等温锻造工艺进行了研究,结果表明,FGH96合金经晶粒细化处理后,在1020～1100℃,具有良好的超塑性;FGH96合金超塑变形时流变应力比热等静压后直接变形时显著降低,在1050℃以1×10-4s-1进行恒应变速率压缩变形,其流变应力只有60MPa左右;将FGH96合金超塑性变形应用于大型涡轮盘的等温锻造,使小设备超塑性等温锻造大型涡轮盘锻件成为可能.     

FGH95合金涡轮盘等温锻造工艺研究

对ＦＧＨ９５合金涡轮盘件的成形工艺进行了研究，通过热等静压制坯，双缓冷预处理工艺及等温锻造工艺，研制出了直径２２０ｍｍ的模拟盘件。     

预处理工艺对FGH95合金流动应力的影响

研究了不同预处理工艺对ＦＧＨ９５合金等温变形时流动应力的影响，确定了合金的预处理工艺方案，为涡轮盘的试制提供了依据。     

高强高韧Al-Cu-Li-Mg-Zr-Zn-Mn合金热变形行为

在Gleeble～1500热模拟实验机上，采用高温等温压缩，应变速率为0．001～10／s，变形温度为360～520％，对通用型铝锂合金在高温压缩变形中的流变应力行为进行了研究，分析了其高温变形的物理本质。结果表明：在等应变速率下，真应力随温度的升高而降低；在相同的变形温度下，随应变速率的增加，流变应力水平升高。在较低的变形速率及较高的变形温度条件下热变形时，通用型铝锂合金容易发生动态再结晶。而变形速率较高，变形温度较低时，通用型铝锂合金可能发生剪切变形，热变形过程中则主要发生动态回复。     

TC11合金热变形特性及变形参数对组织的影响

通过热模拟压缩试验,分析了TC11合金的高温变形特性及不同变形参数下的组织演化规律,用非线性回归方法建立了TC11合金Kumar型材料的本构关系,得出了TC11合金的高温流变曲线基本呈流变软化特征的结论;最后应用MSC,Autoforge软件对TC11合金某型号涡轮盘的等温锻造工艺进行了模拟式工艺设计,验证了TC11合金材料本构关系的工程适用性.     

中国变形高温合金研制进展

概述了近10年来我国变形高温合金的研制情况.介绍了航空发动机用涡轮盘材料718Plus,GH4720Li,GH4065合金的特点,燃烧室用GH3230合金以及燃气轮机用GH4706合金的研制进展.并对变形高温合金热加工新技术进行了总结,包括针对易偏析材料开发的ERS-CDS新工艺,改善变形高温合金棒材组织的反复镦拔工艺,提升高性能难变形高温合金热塑性的缓冷处理和热机械循环处理技术.最后,展望了我国变形高温合金产业的未来.     

粉末冶金涡轮盘破裂转速分析与验证

结合改进前粉末冶金涡轮盘的破裂情况、断口分析和破裂转速分析方法,从提高总体强度、降低局部应力和应变、降低残余变形、控制加工工艺等方面,采取增大倒圆、增加辐板厚度等方法对粉末合金涡轮盘进行了结构和工艺上的改进。通过对比分析改进前后涡轮盘的局部应力应变、整体屈服强度储备和残余变形,及后续的涡轮盘破裂转速试验均表明,本文采取的改进措施效果明显,能显著降低破裂位置处的局部应力、提高径向屈服强度及降低盘缘残余变形。     

7050高强度铝合金流变行为研究

通过等温压缩试验研究了7050铝合金在变形温度300~450℃、应变速率0.01 s-1~10s-1条件下的流变应力变化规律,计算并建立了描述7050铝合金高温变形特性的本构方程.结果表明:变形温度和应变速率对7050铝合金流变应力影响显著,随变形温度升高和变形速率的降低,相同变形程度下合金的流变应力显著降低,并且在较低的应变下合金即可达到稳态流变状态.经计算,在本试验条件下,7050铝合金的热变形激活能为151.63 kJ/mol.     

新型镍基粉末高温合金的高温变形行为

采用Gleeble-1500热模拟机对新型第三代镍基粉末高温合金FGH98Ⅰ在不同变形温度(950~1150℃)及不同变形速率(0.0003~1s-1)下高温变形行为进行了研究,绘制了动态RTT曲线,并建立了合金的热变形本构关系。结果表明:合金的流变应力随变形温度的升高和应变速率的降低而降低,当变形温度≤1100℃、应变速率≥0.0003s-1时,其流变应力随应变量增加呈动态再结晶特征;在应变速率≤0.01s-1的高温变形条件下,其动态再结晶的开始时间与变形温度无线性关系;实验验证了采用考虑应变量的双曲正弦模型能较好地反映合金在热变形过程中流变应力的变化规律。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

ν-gap度量及其在飞行控制律评估中的应用

 传统控制律评估方法主要用于单输入单输出（SISO）系统，且对模型参数摄动考虑不够全面,针对这些不足，研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上，给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算，提出ν-gap度量评估控制律的步骤。实例结果表明，该方法不仅克服了上述传统评估方法的缺陷，而且还有根据所求的各摄动影响情况忽略影响小的元素，以减少计算量及可以找到最坏情况下的参数摄动组合等优点。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Integrated Entry Guidance for Reusable Launch Vehicle

A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。