带有不确定因素的最优拦截制导律

本文从微分对策观点出发,利用极小极大原理讨论了带有不确定因素的最优拦截制导律。在选择特定的过渡时间时,最优拦截制导律具有综合形式。仍由二部分组成:一部分是变系数比例导航,另一部分是与导弹加速度有关的修正项。     

Optimum FFT-based frequency acquisition with application toCOSPAS-SARSAT

In the case of a single sinusoid or multiple well-separated sinusoids, a coarse estimator consisting of a windowed Fourier transform followed by a fine estimator which is an interpolator is a good approximation to an optimal frequency acquisition and measurement algorithm. The design tradeoffs are described. It is shown that for the fine-frequency estimator a good method is to fit a Gaussian function to the fast-Fourier-transform (FFT) peak and its two neighbors. This method achieves a frequency standard deviation and a bias in the order of only a few percent of a bin. In the case of short-time stationarity, for a moderate number of averages and for an adaptive threshold detector, only between 0.5 and 1 dB is lost when averaging is traded off for FFT length, in contrast to the asymptotic result of 1.5 dB. The COSPAS-SARSAT satellite system for emergency detection and localization is used to illustrate the concepts. The algorithm is analyzed theoretically, and good agreement is found with test results     

二元非线性机翼随机动力学行为

 为考查在高斯白噪声作用下二元机翼随机颤振动力学行为,采用数值仿真的方法对其进行了研究。首先把机翼简化成一个具有扭转和上下自由度的平板,其中扭转弹簧具有3次非线性刚度,同时假设空气是线性不可压的而且气动力是定常的,再对任意运动和高斯白噪声作用下的机翼进行建模。其次采用了蒙特卡罗仿真来求解随机微分方程的数值解,根据数值解结果进行统计分析,计算出最大Lyapunov指数。最后得出：在随机激励作用下机翼的动力学行为与确定性颤振相比有很大差异,同时随机颤振点提前于确定性颤振点。     

Measurement of Distributed Targets with the Random Signal Radar

A model of a distributed target as a collection of independent, Poisson distributed point scatterers or scattering centers in a range-velocity target space is introduced and is characterized by a deterministic function called the ?scatterer density function.? This function is the density of the point scatterers in the range-velocity space and can be estimated in a relatively straightforward manner by any radar having adequate resolution in both range and velocity and no ambiguities in the region occupied by the distributed target. The use of the random signal radar with a correlator receiver is considered here and the statistical properties of the correlator output, when the return signal is from a distributed target, are derived. It is shown that the spectral density is simply related to the scatterer density function. The technique is illustrated by an example in which the target is a tornado modeled as a cylinder with constant angular velocity. The example suggests that is a possible to remotely estimate the radar cross section per unit volume as a function of distance from the center of the tornado.     

Analysis of a Class of Nonlinear Sampled-Data Systems with a Gaussian Input Signal

The problem treated here is the analysis of a class of nonlinear sampled-data systems with a Gaussian input signal. The nonlinear element is a symmetrical limiter (memoryless device) that feeds the linear element. Preceding the limiter is a sampler and zero-order hold unit for data reconstruction. The analysis is predicated on finding an equivalent gain for the nonlinear element such that the mean-square error is a minimum. The nonlinearity is thus replaced by a linear component and the system is then analyzed by conventional techniques. It is also shown that for appropriate sampling rates the sampled-data system is equivalent to a continuous system due to the action of the sampler-hold combination. All calculations pertaining to the limiter input signal require the use of a transfer function that is interior to the feedback loop. However, in developing this transfer function, the overall system is considered so that the system output may be evaluated after the value of equivalent gain has been found.     

柔性航天器大角度操纵的直接输出反馈控制

 本文研究了柔性航天器大角度操纵的控制问题,提出了直接输出反馈控制方法。证明了通过输出的线性反馈,用少量的控制器可以达到柔性航天器的渐近稳定调节。同时给出了所需控制器数目及其设置条件,并给出了直接输出反馈控制所对应的最优指标,从而实现了利用少量控制器控制高维非线性系统。     

基于普通分离原理的制导/估计综合设计方法

现有的先进制导律研究常常分离设计最优估计器和最优制导律,但是这种分离设计没有被证明是有效和最优的设计方法.本文基于普通分离原理(GST),提出一种制导/估计综合设计方法.首先,将拦截器反导作战模型考虑为一类非线性、非高斯追逃拦截问题,建立了噪声环境中追逐-逃逸对策模型;其次,引入追逃未达集概念,利用几何方法将估计器设计...     

A Correlation Polarimeter for Noise-Like Signals

Optimum estimation (tracking) of the polarization plane of a linearly polarized electromagnetic wave is determined when the signal is a narrow-band Gaussian random process with a polarization plane angle which is also a Gaussian random process. This model is Compared to previous work and is applicable to space communication. The estimator performs a correlation operation similar to an amplitude -comparison monopulse angle tracker, giving the name correlation polarimeter. Under large signal-to-noise ratio (SNR), the estimator is causal. Performance of the causal correlation polarimeter is evaluated for arbitrary SNR. Optimum precorrelation filtering is determined. With low SNR, the performance of this system is far better than that of previously developed systems. Practical implementation is discussed. A scheme is given to reduce the effect of linearly polarized noise.     

最小成本加快法中的优化组合方案定理及其计算机程序

本文提出了最小成本加快法中寻找多关键路线情况下的组合压缩方案的方法,并用图论中有关割集的理论进行了论证,得到了优化组合方案定理。该定理指出:在由网络计划图中的关键路线构成的子图中,如果每项作业都允许压缩或放宽作业时间,则其最小费用率完全割集中的每个正向割弧(作业)压缩单位时间,每个反向割弧(作业)放宽单位时间,则总工期以最低成本压缩单位时间。文中详细介绍了这种算法。     

高阶系统的降阶控制研究

本文根据线性随机系统的最优控制理论较详细地给出了利用优化技术对高阶系统进行降阶控制的理论分析,并对提高整个控制系统的稳定性提出了一种改进方法.最后对飞机机翼的最简模型——自由-自由梁的振动抑制进行了具体的计算,取得了较为满意的结果。     

基于轨迹成型的攻击角度与时间控制

假定所成型的导弹飞行轨迹由圆弧段和直线段构成,直线段经过目标点且满足导弹末端攻击角度的要求,圆弧段起始于导弹初始位置且与直线段相切于待定的点,该点由指定的导弹攻击时间通过迭代算法得到。给出了可行的攻击时间范围。在轨迹成型的基础上,提出一种新的虚拟目标轨迹跟踪控制方法：在圆弧段提出一种前馈加反馈的复合控制方案,在直线段提出一种带角度控制的比例导引方案。该方法是一种几何方法,易于工程实施。仿真结果表明,该方法可以有效地同时对攻击角度与攻击时间进行控制。     

细长管道耦合振动频率特性及结构可靠性分析

本文针对细长流固耦合作用系统,采用弹性-声学梁模型,用“质量流”作流体变量,位移体结构变量,得出了对称的有限元耦合方程,并据此进行了实例分析。再以渗漏作为管道失效的标准,根据概率断裂力学模型,考虑循环振动应力的影响,用蒙特-卡罗法对管道失效现象进行了数字模拟,给出了不同循环数和循环应力下的失效概率。     

Attitude control of a satellite with redundant thrusters

Redundant thrusters are generally used for a reliable attitude control system. Also, redundant thrusters yield a better performance if they are used appropriately. In this paper, the authors propose an efficient redundancy management algorithm to reduce the fuel consumption. The algorithm is based on a linear programming problem which is a constrained optimization problem. For the algorithm, a cost function is defined as a quantity related to the fuel consumption for a maneuver. The independent variables are the thrusters' on-times which are control input variables of a satellite dynamic model. The advantage of the proposed method is verified by numerical examples. The examples show that the proposed method consumes less fuel than an existing method for a given maneuvering command. A sub-optimal algorithm is also discussed for an onboard computation. The proposed algorithm is applied to two maneuvers: move-to-rest and rest-to-rest. This is verified by a numerical simulation.     

大小叶片轴流级反问题设计及数值模拟

 在常规轴流级流线曲率法通流设计和任意中弧线叶型造型方法的基础上,引入了适合于大小叶片的当量扩散因子叶型损失模型,发展了用Miller-Lewis-Hartmann(M-L-H)模型分别计算大叶片和小叶片激波损失的复合激波模型,制定了大小叶片装配方法,建立了大小叶片通流反问题设计系统。用该系统对某级增压比为2.20的单级高负荷后掠风扇进行了后掠和前掠大小叶片改型设计。经计算流体力学(CFD)检验,维持后掠造型的改型,在不提高设计点增压比的条件下,级绝热效率相当,流量和失速裕度都得到了提高;而大小叶片结合前掠的改型,当考虑单排静子的最大载荷将设计级增压比提高至2.31时,级绝热效率略微降低约0.3%,流量略减,失速裕度则显著提高。算例也表明通流反问题设计系统适合于大小叶片轴流级的设计。     

机翼对自转旋翼机纵向稳定性的影响

为了研究机翼对自转旋翼机纵向稳定性的影响,针对某复合式自转旋翼机,建立了基于状态空间法描述的非线性全量方程数学模型。该模型包含自转旋翼、机身、螺旋桨、机翼和尾翼的气动模型、动态入流模型和稳定性分析模型。运用该模型对比研究了样例自转旋翼机和样例复合式自转旋翼机的纵向稳定性。研究结果表明：机翼的增加对于浮沉模态和短周期模态稳定性是有利的;对于旋翼转速模态稳定性是不利的,在设计复合式自转旋翼机时可以考虑增加旋翼桨尖配重来提高此模态的稳定性。机翼的纵向位置对自转旋翼机的纵向稳定性有显著影响。在机翼纵向位置能满足配平约束条件下,机翼纵向位置越靠后,迎角稳定性越好,但旋翼转速稳定性越差。在设计复合式自转旋翼机时,机翼纵向位置的选择要综合考虑这两个因素进行折中。     

实时离散事件系统的状态反馈逻辑

 基于状态时间的概念,在Ramadge-Wonham模型的基础上提出了一种新的实时离散事件系统模型。在控制目标是保持某给定谓词在闭环系统状态轨迹上为真的情况下,给出了实时控制不变性的定义。研究表明,对这类系统,存在一个状态反馈控制器使给定谓词在闭环系统状态轨迹上保持为真的充要条件是该谓词是实时控制不变的。证明了给定谓词所含的最大实时控制不变子谓词的存在性并给出了计算方法。最后,给出一个例子来说明有关结果。     

An Analysis of the Performance of the Oscillating Limiter Driven by FM Signals Corrupted by Noise

The behavior of the oscillating limiter (OL) driven by FM signals is surveyed, and its performance with signal corrupted by noise is investigated. For high values of the carrier-to-noise ratio (CNR), if the frequency deviation of the signal is small in comparison with the locking range of the OL, it is calculated, and experimentally verified, that a system OL discriminator is equivalent to a system bandpass limiter discriminator followed by a linear network whose frequency response has been specified. When the frequency deviation is not so small, the baseband noise power increases with it; a formula is given that allows the calculation of this power when the signal is such that the circuit operates in quasistationary fashion. For low values of the CNR, a mathematical analysis presents unsurmountable difficulties. However, heuristic argumentation leads to an interpretation of the operation of the OL in the threshold region, which is substantiated by an experimental investigation. The results of this paper enable a comparative evaluation of a system OL discriminator and a system bandpass limiter discriminator, to which the former reduces when the feedback path in the OL is open.     

前置不同诱导轮高速离心泵旋转空化特性研究

以高速诱导轮离心泵为研究对象,开展了无诱导轮、前置等螺距诱导轮、前置变螺距诱导轮及前置分流叶片诱导轮4种情况下离心泵全流道的空化数值模拟和汽蚀特性实验研究.通过外特性实验研究得到:在同一流量下,前置等螺距诱导轮离心泵的扬程最低,前置变螺距诱导轮离心泵的扬程次之,前置分流叶片诱导轮离心泵的扬程较两者稍高.通过汽蚀实验和数值模拟研究得到:在前置3种诱导轮的情况下,离心泵的汽蚀性能都得到了改善,其改善效果从低到高依次是:变螺距诱导轮、分流叶片诱导轮、等螺距诱导轮.通过对汽相体积分数分布情况的研究得到:诱导轮的吸力面除进口外缘容易发生汽蚀外,叶片出口靠近轮毂侧也较容易发生汽蚀;对比分析主叶轮和诱导轮的汽蚀情况,得到诱导轮汽蚀的严重性与离心叶轮的汽蚀严重性并非成正比的结论.     

通过预成形降低内高压成形压力的机理分析

采用力学分析和有限元模拟对空心零件圆角部位在内高压成形过程中的应力分布和变形机理进行了分析,针对多边形截面空心件内高压成形,以矩形截面为例提出采用花瓣形预成形截面降低圆角成形压力的方法,分析了该方法降低圆角成形压力的机理,提出了花瓣形预成形截面形状关键参数计算公式,并通过试验进行了验证,为采用较低压力实现空心构件圆角内高压成形提供了理论指导.     

Robust Control for Static Loading of Electro-hydraulic Load Simulator with Friction Compensation

Load simulator is a key test equipment for aircraft actuation systems in hardware-in-the-loop-simulation. Static loading is an essential function of the load simulator and widely used in the static/dynamic stiffness test of aircraft actuation systems. The tracking performance of the static loading is studied in this paper. Firstly, the nonlinear mathematical models of the hydraulic load simulator are derived, and the feedback linearization method is employed to construct a feed-forward controller to improve the force tracking performance. Considering the effect of the friction, a LuGre model based friction compensation is synthesized, in which the unmeasurable state is estimated by a dual state observer via a controlled learning mechanism to guarantee that the estimation is bounded. The modeling errors are attenuated by a well-designed robust controller with a control accuracy measured by a design parameter. Employing the dual state observer is to capture the different effects of the unmeasured state and hence can improve the friction compensation accuracy. The tracking performance is summarized by a derived theorem. Experimental results are also obtained to verify the high performance nature of the proposed control strategy.