Design optimization for asymmetrical ZVS-PWM zeta converter

In this paper, a new soft-switching Zeta converter with an asymmetrical pulsewidth modulation (PWM) control is proposed. The proposed Zeta converter has the features of constant frequency operation, zero voltage switching (ZVS), and low voltage stress on the active switches. Moreover, it can achieve high power density, high efficiency, low switching loss, and low component count, which make converter operation at low to medium power level feasible. Operational principle of the Zeta converter is presented in detail, and a specific example is designed and implemented to verify its feasibility.     

Fourier theory of jumps applied to converter harmonic analysis

The Fourier theory of jumps (FTJ) is demonstrated as an aid in deriving closed-form analytical equations for converter switching harmonics. The switching waveforms analyzed are the input current and output voltage and current of a three-phase, ac-dc, step-down, dead-band pulsewidth modulated (PWM), unity power factor converter. The input current closed-form harmonic equation is derived for two parallel-connected, interleaved-PWM converters supplying the same load and sharing a common input filter. The equations are compared with PSpice^TM simulations and practical results     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

Pulsewidth Modulator Phase Shift

Phase shift for the ramp-comparator pulsewidth modulator (PWM) between a continuous input control signal and the signal frequency component of the output is analyzed. It is shown that transport lag is not implicit to these PWM systems in general but rather depends upon the existence of explicit delays between the time at which a switching decision is made and the time at which that decision is executed.     

Full control of a PWM DC-AC converter for AC voltage regulation

The design and implement action of a DSP-based fully digital-controlled single-phase pulsewidth modulated (PWM) dc-ac converter for ac voltage regulation is described. The proposed multiloop digital controller (MDC) consists of a current controller, a voltage controller, and a feedforward controller. This MDC was realized using a single-chip digital signal processor (DSP). The PWM gating signals are determined at every sampling instant by the proposed multiloop digital control scheme using a set of detected feedback signals. A software current control; scheme has been developed to achieve fast current control of the PWM inverter and decouple the inductor of the output filter. Experimental results have been given to verify the proposed digital control scheme. The constructed DSP-based PWM dc-ac converter system can achieve fast dynamic response and with low total harmonic distortion (THD) for rectifier type of loads     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Random hysteresis PWM inverter with robust spectrum shaping

A hysteresis current-controlled pulsewidth modulation (PWM) scheme is simple and robust in switching control, but it is subject to not constant switching frequency. However, since its harmonic spectrum is not randomly distributed like those yielded by the random PWM (RPWM) scheme, the annoying harmonic effects still exist. A random switching control strategy is proposed here to let the harmonic spectrum of the hysteresis current-controlled PWM inverter be randomly distributed. First, the effect of varying band on the harmonic distribution characteristic of a hysteresis current-controlled PWM scheme is analyzed. Then a random hysteresis PWM scheme and its quantitative design procedure are proposed. Finally, a robust spectrum shaping technique is devised such that the desired harmonic distribution pattern can be achieved. In the resulting frequency spectrum, the magnitudes of lower frequency harmonics are shaped and reduced. Hence the inverter output with a better harmonic attribute is obtained. Validity of the proposed random hysteresis PWM scheme is verified by some simulated and measured results     

Alternate forms of the PWM switch models

Vorperian's pulsewidth modulation (PWM) switch model consists of a PWM transformer and a nonlinear resistor. The recognition that any of the three transformer terminals can serve as the common terminal leads to two alternate PWM transformer models and the corresponding two alternate PWM switch models. For a given PWM dc-dc converter, one of the three PWM switch models is more “natural” for graphic-oriented analysis/design, e.g., it allows the idealized converter to be analyzed by inspection. Furthermore, all three PWM transformers may be used to graphically manipulate the converter circuit to a form that can be analyzed by inspection. The alternate forms of the PWM transformers and the PWM switch models are effective as graphic-oriented teaching and learning tools for PWM converters. This is demonstrated using examples based on the boost converter and the Cuk converter     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

Implementation of nondeterministic pulsewidth modulation forinverter drives

A single-phase power factor preregulator to improve the power quality in the input side of an ac/dc/ac converter and a random pulsewidth modulation (PWM) to reduce the emitted noise energy and the mechanical vibration for an induction motor drive is proposed. The hysteresis current control (HCC) technique for a voltage source switching mode rectifier (SMR) is adopted. A control scheme is presented such that the line current is driven to follow the reference current which is derived from the dc bus voltage regulator and the output power estimator. A random pulse position technique for a three-phase voltage source inverter system to reduce the noise energy and resonant vibration from ac machine drive is described. By randomly varying the instantaneous pulse position in each switching frequency, the frequency distribution of harmonics is spread in a wide frequency range which results in reduction of torque pulsations in the ac motor drive systems. To investigate the proposed control scheme, experimental tests based on a laboratory prototype were implemented to show the nearly unity power factor at the SMR and reduce the noise energy concentrated at the specific tones     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

A new zero-voltage switching DC/DC boost converter

A pulsewidth-modulated (PWM) zero-voltage-switching quasi-resonant boost converter operating at constant switching frequency is presented. In contrast to the frequency-modulated (FM) zero-voltage-switching quasi-resonant boost converter, this converter possesses better controllability and higher operating performance, and overcomes the instability caused by the parasitic oscillation. The principle of operation and performance of the converter are presented. Its two-dimensional state trajectories and steady-state characteristic curves are derived which are useful for the converter design. Both the SPICE simulation and experimental result agree with the theoretical prediction     

并联H桥DC/DC变换器软开关技术研究

与传统的Buck电路相比,基于H桥并联的DC/DC变换器可以实现电压的双极性输出和故障时的冗余控制,非常适合用于大功率电动机正反转控制的场合。分析了并联H桥型DC/DC变换器的结构组成和双脉宽调制(PWM)模式。为了降低双脉宽调制下H桥型DC/DC变换器的开通和关断损耗,对无源软开关技术进行了分析,重点探讨了RCD缓冲电路和最小应力缓冲电路之间的性能差异,指出最小应力软开关技术可以获得更好的软开关性能,并就将其用于双脉宽调制下的并联H桥DC/DC变换器进行了仿真研究。仿真结果表明:最小应力软开关技术用于双脉宽调制下并联H桥DC/DC变换器时,可以实现开关管的零电压开通和零电流关断。     

Single-phase three-level rectifier and random PWM inverter drives

A novel ac/dc/ac converter topology with three-level pulsewidth modulated (PWM) scheme for the single-phase ac/dc rectifier and random PWM scheme for ac drives is proposed. In order to improve the power quality in the single-phase rectifier, a ROM-based (read-only memory) control scheme, based on hysteresis current comparator, region detector, and capacitor compensator, is used to achieve a sinusoidal line current with low current distortion. The control scheme of the adopted three-level rectifier is easy to implement. The blocking voltage of power switches is clamped to half of the dc bus voltage. To reduce the mechanical vibration from an induction motor, random pulse position PWM scheme is adopted to spread the harmonics in a wide frequency range which results in the reduction of torque pulsation in the ac motor drives. Simulation and experimental results based on the laboratory prototype circuit are presented to verify the proposed control scheme     

Simplified analysis of PWM converters using model of PWM switch.Continuous conduction mode

A circuit-oriented approach to the analysis of pulsewidth modulation (PWM) converters is presented. This method relies on the identification of a three-terminal nonlinear device, called the PWM switch, which consists of only the active and passive switches in a PWM converter. Once the invariant properties of the PWM switch are determined, its average equivalent circuit model can be derived. This model is versatile enough to easily account for storage-time modulation of bipolar junction transistor(s) (BJTs); the DC- and small-signal characteristics of a large class of PWM converters can then be contained by a simply replacing the PWM switch with its equivalent circuit model. The methodology is very similar to linear amplifier circuit analysis, whereby the transistor is replaced by its equivalent circuit model     

基于TMS320F2812生成移相PWM的2种办法

移相 PWM波是很多开关电源常用的驱动脉冲信号。双向全桥直流变换器(Bidirectional-Full-Bridge DCDC Converter,BDC)在双重移相控制方式下时需要 4组两两互补的移相 PWM波。文章基于 TMS320F2812型 DSP(Digital Signal Processor)分析了 2种生成移相 PWM的方法。为提高双向全桥直流变换器工作的安全性和可靠性,为移相 PWM波设置死区时间。对所提出的方法进行测试后结果良好,对于双向全桥直流变换器闭环控制系统的构建具有重要意义。     

PWM full-bridge converter with natural input power factor correction

A pulsewidth modulated (PWM) full-bridge converter that simultaneously performs input power factor correction (PFC) and DC-DC conversion is proposed. The converter is the same as the standard voltage-fed PWM full-bridge converter with a diode-bridge low-pass filter front end, but with a slight modification that results in an improvement in power factor that is sufficient to satisfy the EN61000-3-2 requirements for electrical equipment. The operation of the converter is explained and analyzed, and the results of the analysis are used to determine the converter's steady-state characteristics, which are discussed in detail. A design procedure for the selection of components is then derived and demonstrated with an example. The feasibility of the converter and its ability to satisfy EN61000-3-2 requirements on electrical equipment is shown with results obtained from an experimental prototype.     

Simplified analysis of PWM converters using model of PWM switch.II. Discontinuous conduction mode

For pt.I see ibid., vol.26, no.3, p.490-6 (1990). According to the method of state-space averaging, when a pulsewidth modulation (PWM) converter enters discontinuous conduction mode (DCM), the inductor current state is lost from the average model of the converter. It is shown that there is neither theoretical nor experimental justification for the disappearance of the inductor state as claimed by the method of state-space averaging. For example, when the model of the PWM switch in DCM is substituted in the buck, boost, or buck-boost converter while the inductor is left intact, the average model has two poles: the first pole f_p1 agrees with the single pole of state-space averaging, while the second pole f_p2 occurs in the range f_p2⩾F_s/π. It is shown that the right-half plane zeros present in the control-to-output transfer functions of the boost, buck-boost, and Cuk converters in continuous conduction mode are also present in discontinuous conduction mode     

具有功率因数校正的零电压开关谐振变换器设计

传统型PWM控制的开关电源是硬件开关，开关损耗大，不利于向小型化，轻量化发展。本提出利用零电压开关谐振技术实现功率开关管的软开关技术，从而降低开关损耗，并采用SG3525为核心的主开关控制电路，提高系统的动态响应性能，同时采用UC3854对AC／DC变换过程作了功率因数校正，以改善输入电流的波形，提高电力资源的利用率。     

Mathematical modeling of an armature assembly in pilot stage of a hydraulic servo valve based on distributed parameters

The dynamic performance of a nozzle-flapper servo valve can be affected by several factors such as the disturbance of the input signal, the motion of the armature assembly and the oscillation of the jet force. As the part of vibrating at high frequency, the armature assembly plays a vital role during the operation of the servo valve. In order to accurately predict the transient response of the armature assembly during the vibration, a mathematical model of armature assembly is established based on the distributed parameters method (DPM) and Hamilton principle. The new mathematical model is composed of three main parts, the modal eigenfunction, modal mechanical response expressions of the spring tube and the motion equation of the other armature assembly. After programing, the purpose of using the DPM to predict the dynamic response of different positions located on the armature assembly is achieved. For verifying the validity of the mathematical model, the finite element method (FEM) and classic model (CM) of armature assembly are applicated by commercial software under the same condition. The comparison results prove that the DPM can effectively predict the axial and tangential deflection of the armature assembly different positions which the CM can’t duing to its over-simplification. A certain error is generated when predicting the axial deformation at different heights by DPM, which is caused by an approximate method to simulate the torsion of the spring tube. The comparison results of the spring tube deflection at different vibration frequencies shows that the adaptability of DPM is significantly higher than the classic model, which verify the model is more adaptable for predicting the dynamic response of the armature assembly.