波音737NG飞机WXR-2100气象雷达PWS FAIL故障分析

现代机载气象雷达应用多普勒频移原理实现风切变的探测,本文分析了装载WXR-2100型机载气象雷达的波音737NG飞机PWS FAIL这一常见故障的原因,为快速排故提供了参考.     

WXR-270气象雷达典型故障分析

机载气象雷达是为了防范气象风险、保证飞行安全而研制的航空电子系统,本文以WXR-270气象雷达为研究对象,简单介绍了其工作原理及组成,重点针对4例典型故障进行故障原因分析。     

一种能量级自然云雷达图像仿真方法

针对飞行模拟训练需求,基于自然云与电磁波束相互作用的统计特性,设计了 1种自然云雷达图像仿真方案,给出了多个关键仿真模型的实现方法。通过雷达波束的子波束划分实现雷达波束充塞系数的估算,解决了波束充塞系数计算难度大的问题,并根据云的三维模型设计了雷达回波能量计算模型。通过将三维空间的计算转化到二维平面内以获取雷达波束中心与云团交点位置及参数,以此计算雷达反射率和雷达回波的距离衰减。仿真实验表明:该方法能较好地体现云对回波的衰减效应,以及波束充塞度对远距离云回波计算的影响,具有较好的实时性。     

基于相控阵雷达天线俯仰多波位相扫的设计与应用

分析研究了如何设计平面相控阵雷达天线多波位相扫的基本原理,提出了36行平面相控阵雷达天线在俯仰上实现多波位发射波束、接收波束形成与展宽方法.通过微波暗室的测试,天线技术指标完全达到了平面相控阵雷达天线多波位相扫的技术要求,实现了一维相控阵面高增益、高灵敏度、低噪声、大动态范围技术指标.     

相控阵雷达导引头波束稳定技术研究

 相控阵雷达导引头已成为新型空空导弹制导系统的首选,相控阵雷达导引头应用在空空导弹上需要首先解决导引头波束稳定的技术难题。本文基于波束指向在惯性空间不变性原理提出一种相控阵雷达导引头波束稳定算法,对影响相控阵雷达导引头隔离度性能的主要因素进行了仿真分析。仿真结果表明:该算法可以实现相控阵雷达导引头波束惯性空间指向稳定并且满足工程应用要求;通过减小速率陀螺数据周期和波束控制周期,及引入速率陀螺传输延时补偿算法可以提高导引头的隔离度性能。     

相控阵测控系统的特点和主要技术问题

在比较相控阵测控系统和相控阵雷达的基础上,归纳出相控阵测控系统的特点,根据研制相控阵多目标测控系统和TDRSS-SMA的体会,概述了它的测轨精度、波束形成、分时多波束和同时多波束、自适应时-空二维滤波、边扫描边跟踪和多目标跟踪、共形相控阵和宽角扫描以及降低造价等问题。     

ALE-9开阵天线辐射柱故障分析

针对单脉冲二次雷达所使用的ALE-9开阵天线,研究了辐射柱故障对雷达水平波束的影响。通过分析发现雷达天线各辐射柱的状态对天线水平波束的影响是不同的。通过大量的计算找出影响水平波束形状的关键柱体,从而在实际中加以重点监测和维护。     

非均匀线阵数字多波束测向算法研究

提出了一种适用于非均匀线阵的数字多波束测向方法,该方法首先通过数字配相法形成同时多波束,然后根据目标信号在相邻三波束的输出值来估计目标方向,通过给出数字阵列雷达的系统架构,建立非均匀线阵信号模型,对上述方法进行了计算机仿真分析,仿真结果证明了该方法的有效性     

机载单通道雷达实波束扫描的前视探测

针对机载单通道雷达采用合成孔径雷达(SAR)技术、多普勒波束锐化(DBS)技术等途径难以实现载机飞行路线正前方高分辨率成像问题,研究了一种利用方位实波束重叠扫描的新型机载单通道雷达前视探测方法,讨论了提高方位分辨率的可行性和适用条件。该方法根据目标回波强度受到波束扫描增益调制的特点,通过计算修正的Capon空间谱来实现方位超分辨。模拟实验表明,所提方法能够实现机载单通道雷达的前视成像,可以显著提高波束主瓣区域内强弱临近目标的分辨能力。     

一种基于雷达波束驻留模式的空间碎片轨道参数估计方法

利用窄波束的单脉冲精密跟踪雷达波束驻留模式进行碎片探测是空间碎片环境统计特征描述的一种重要途径。由于该模式观测弧段极短,且无法获取同一目标的多个弧段,因而利用常规定轨方法难以达到理想的效果。在圆轨道假设下,提出了一种利用波束驻留模式获取的单个极短弧计算碎片轨道高度和倾角的方法。首先利用碎片的距离确定其轨道高度;在此基础上,根据推导出的不同波束指向时碎片的距离变化率与轨道倾角的关系,得出其轨道倾角。该方法对于正南、正东指向的雷达波束驻留模式均适用,其中正南指向时还需利用方位角和仰角数据来区分轨道倾角与补角;但不适用于波束指向天顶的情况。仿真结果验证了方法的有效性。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.