Implementing digital terrain data in knowledge-aided space-time adaptive processing

Many practical problems arise when implementing digital terrain data in airborne knowledge-aided (KA) space-time adaptive processing (STAP). This paper addresses these issues and presents solutions with numerical implementations. In particular, using digital land classification data and digital elevation data, techniques are developed for registering these data with radar return signals, correcting for Doppler and spatial misalignments, adjusting for antenna gain, characterizing clutter patches for secondary data selection, and ensuring independent secondary data samples. These techniques are applied to select secondary data for a single-bin post-Doppler STAP algorithm using multi-channel airborne radar measurement (MCARM) program data. Results with the KA approach are compared with those obtained using the standard sliding window method for choosing secondary data. These results illustrate the benefits of using terrain information, a priori data about the radar, and the importance of statistical independence when selecting secondary data for improving STAP performance     

基于杂波子空间估计的MIMO雷达降维STAP研究

 多输入多输出(MIMO)雷达是近年来出现的一种新体制雷达,针对MIMO体制的机载雷达开展空时自适应处理（STAP）技术研究是值得进一步努力的方向。本文研究了机载MIMO雷达STAP技术的降维算法,通过对STAP技术杂波抑制原理进行分析,推导并得到一种基于杂波子空间的降维算法。结合扁长椭球波函数（PSWF）的特点,提出了一种基于杂波子空间估计的降维算法,并与若干降维算法的杂波抑制性能进行比较。结果表明,当存在阵元幅相误差时,该算法在保持杂波抑制性能的同时能够有效地降低STAP算法的运算量。     

Framework and Taxonomy for Radar Space-Time Adaptive Processing (STAP) Methods

The goal of radar space-time adaptive processing (STAP) is to detect slow moving targets from a moving platform, typically airborne or spaceborne. STAP generally requires the estimation and the inversion of an interference-plus-noise (I+N) covariance matrix. To reduce both the number of samples involved in the estimation and the computational cost inherent to the matrix inversion, many suboptimum STAP methods have been proposed. We propose a new canonical framework that encompasses all suboptimum STAP methods we are aware of. The framework allows for both covariance-matrix (CM) estimation and range-dependence compensation (RDC); it also applies to monostatic and bistatic configurations. Finally, we discuss a taxonomy for classifying the methods described by the framework.     

Sensitivity of MIMO STAP Radar with Waveform Diversity

Space-time adaptive processing (STAP) is an effective method adopted in airborne radar to suppress ground clutter. Multiple-input multiple-output (MIMO) radar is a new radar concept and has superiority over conventional radars. Recent proposals have been applying STAP in MIMO configuration to the improvement of the performance of conventional radars. As waveforms transmitted by MIMO radar can be correlated or uncorrelated with each other, this article develops a unified signal model incorporating waveforms for STAP in MIMO radar with waveform diversity. Through this framework, STAP performances are expressed as functions of the waveform covariance matrix (WCM). Then, effects of waveforms can be investigated. The sensitivity, i.e., the maximum range detectable, is shown to be proportional to the maximum eigenvalue of WCM. Both theoretical studies and numerical simulation examples illustrate the waveform effects on the sensitivity of MIMO STAP radar, based on which we can make better trade-off between waveforms to achieve optimal system performance.     

Robust space-time adaptive processing for airborne radar in nonhomogeneous clutter environments

Space-time adaptive processing (STAP) holds tremendous potential for the new generation airborne surveillance radar, in which the phased array antennas and pulse Doppler processing mode are adopted. A new STAP approach using the multiple-beam and multiple Doppler channels is presented here for airborne phased array radar. The approach with space-time multiple-beam (STMB) architecture is robust to array errors and has very low system degrees of freedom (DOFs). Hence, it has low sample support requirement and it is very suitable for the practical planar phased array radar under nonhomogeneous clutter environments. Meanwhile, a new nonhomogeneous detector (NHD) based on the correlation dimension (CD) is also proposed here, which is used as an effective method to screen tracing data prior to detection processing. It can further improve the performance of the STAP approach in the severely nonhomogeneous clutter environments. Therefore, a scheme that incorporates the correlation dimension nonhomogeneity detector (CD-NHD) with the STMB is recommended, which we term CD-NHD-STMB. The experimental simulation results indicate that: 1) the STMB processor is robust to array element error and has high performance under nonhomogeneous clutter environments; 2) the CD-NHD is also effective on the nonhomogeneous clutter. As a result, the CD-NHD-STMB scheme is robust to array element error and nonhomogeneous clutter, and therefore available for airborne phased array radar applications.     

Airborne/spacebased radar STAP using a structured covariance matrix

It is shown that partial information about the airborne/spacebased (A/S) clutter covariance matrix (CCM) can be used effectively to significantly enhance the convergence performance of a block-processed space/time adaptive processor (STAP) in a clutter and jamming environment. The partial knowledge of the CCM is based upon the simplified general clutter model (GCM) which has been developed by the airborne radar community. A priori knowledge of parameters which should be readily measurable (but not necessarily accurate) by the radar platform associated with this model is assumed. The GCM generates an assumed CCM. The assumed CCM along with exact knowledge of the thermal noise covariance matrix is used to form a maximum likelihood estimate (MLE) of the unknown interference covariance matrix which is used by the STAP. The new algorithm that employs the a priori clutter and thermal noise covariance information is evaluated using two clutter models: 1) a mismatched GCM, and 2) the high-fidelity Research Laboratory STAP clutter model. For both clutter models, the new algorithm performed significantly better (i.e., converged faster) than the sample matrix inversion (SMI) and fast maximum likelihood (FML) STAP algorithms, the latter of which uses only information about the thermal noise covariance matrix.     

Partially Adaptive STAP using the FRACTA Algorithm

A partially adaptive space-time adaptive processor (STAP) utilizing the recently developed FRACTA algorithm is presented which significantly reduces the high computational complexity and large sample support requirements of fully adaptive STAP. Multi-window post-Doppler dimensionality reduction techniques are employed to transform the data prior to application of the FRACTA algorithm. The FRACTA algorithm is a reiterative censoring (RC) and detection algorithm which has been shown to provide excellent detection performance in nonhomogeneous interference environments. Two multi-window post-Doppler dimensionality reduction techniques are considered: PRI-staggered and adjacent-bin. The partially adaptive FRACTA algorithm is applied to the KASSPER I (Knowledge-Aided Sensor Signal Processing & Expert Reasoning) challenge datacube. The pulse repetition interval (PRI)-staggered approach with D=6 filters per Doppler bin is found to provide the best detection performance, outperforming the fully adaptive case while simultaneously reducing the runtime by a factor of ten. Using this implementation, partially adaptive FRACTA detects 197 out of 268 targets with one false alarm. The clairvoyant processor (the covariance matrix for each range cell is known) detects 198 targets with one false alarm. In addition, the partially adaptive FRACTA algorithm is shown to be resilient to jamming, and performs well for reduced sample support situations. When compared with partially adaptive STAP using traditional sliding window processing (SWP), the runtime of partially adaptive FRACTA is 14 times faster, and the detection performance is significantly increased (SWP detects 46 out of 268 targets with one false alarm).     

Knowledge-based space-time adaptive processing for airborne earlywarning radar

This paper describes an innovative concept for knowledge-based control of space-time adaptive processing (STAP) for airborne early warning radar. The knowledge-based approach holds potential for significant performance improvements over classical STAP processing in nonhomogeneous environments by taking advantage of a priori knowledge. Under this approach, knowledge-based control is used to direct pre-adaptive filtering, and to carefully select STAP algorithms, parameters, and secondary data cells     

STAP with medium PRF mode for non-side-looking airborne radar

Space-time adaptive processing (STAP) has been widely discussed for airborne radar systems to improve the system performance of detecting targets. This is especially true for airborne early warning (AEW) radar, which should find long-range and small radar cross section (RCS) targets such as the stealth aircraft and missiles. However, in existing airborne radar literature, STAP is mainly considered for clutter and jamming rejection in side-looking airborne radar (SLAR) applications. There have been fewer discussions on airborne radar with non-side-ways looking array radar (non-SLAR). The STAP of non-SLAR such as forward looking array radar is also very important and can not be avoided for airborne radar to detect targets in all directions. The STAP of the non-SLAR is studied here. A scheme has been proposed, which is processed by the way of STAP combined with multiple staggered medium pulse repetition frequencies (PRFs). We further study the selection of PRFs in order to make the scheme more available for non-SLAR radar. We analyze two typical non-SLAR cases, i.e., inclined-sideways looking array and forward looking array. We examine this scheme by comparing the performances of three processing systems under the criteria of range-velocity blind zone minimization. Computer simulation results show the multiple-PRFs STAP scheme is feasible for non-SLAR and can be applied to phased-array AEW radar systems     

Space-time adaptive radar performance in heterogeneous clutter

Traditional analysis of space-time adaptive radar generally assumes the ideal condition of statistically independent and identically distributed (IID) secondary data. To the contrary, measured data suggests realistic clutter environments appear heterogeneous and so the secondary data is no longer IID. Heterogeneity leads to mismatch between actual and estimated covariance matrices, thereby magnifying the loss between the adaptive implementation and optimum condition. Concerns regarding the impact of clutter heterogeneity on space-time adaptive processing (STAP) warrant further study. To this end, we propose space-time models of amplitude and spectral clutter heterogeneity, with operational airborne radar in mind, and then characterize expected STAP performance loss under such heterogeneous scenarios. Simulation results reveal loss in signal-to-interference plus noise ratio (SINR) ranging between a few tenths of a decibel to greater than 16 dB for specific cases     

基于3DT的空时自适应单脉冲参数估计算法

空时自适应处理(STAP)是机载预警雷达抑制杂波和干扰的一项关键技术,而多普勒三通道联合自适应处理(3DT)是适合工程实现的降维(RD)STAP方法。STAP目标检测后还需进一步估计目标的角度参数,因此将自适应单脉冲(AM)技术引入3DT,提出了一种高精度联合估计目标速度与方位空间角的空时自适应单脉冲算法。理论分析与仿真实验结果表明,当目标多普勒频率偏离检测多普勒单元中心频率时,该算法能同时减少目标多普勒跨越损失和空时导引矢量失配损失,进而提高输出信杂噪比(SCNR),改善目标测角精度。     

Space-time adaptive processing and adaptive arrays: specialcollection of papers

Space-time adaptive processing (STAP) and related adaptive array techniques hold tremendous potential for improving sensor performance by exploiting signal diversity. Such methods have important application in radar, sonar, and communication systems. Recent advances in digital signal processing technology now provide the computational means to field STAP-based systems. The objective of this special collection of papers is to examine the current state-of-the art in STAP technology and explore the remaining obstacles, practical issues and novel techniques required to implement STAP-based radar, sonar or communication systems     

Importance sampling for characterizing STAP detectors

This paper describes the development of adaptive importance sampling (IS) techniques for estimating false alarm probabilities of detectors that use space-time adaptive processing (STAP) algorithms. Fast simulation using IS methods has been notably successful in the study of conventional constant false alarm rate (CFAR) radar detectors, and in several other applications. The principal objectives here are to examine the viability of using these methods for STAP detectors, develop them into powerful analysis and design algorithms and, in the long term, use them for synthesizing novel detection structures. The adaptive matched filter (AMF) detector has been analyzed successfully using fast simulation. Of two biasing methods considered, one is implemented and shown to yield good results. The important problem of detector threshold determination is also addressed, with matching outcome. As an illustration of the power of these methods, two variants of the square-law AMF detector that are thought to be robust under heterogeneous clutter conditions have also been successfully investigated. These are the envelope-law and geometric-mean STAP detectors. Their CFAR property is established and performance evaluated. It turns out the variants have detection performances better than those of the AMF detector for training data contaminated by interferers. In summary, the work reported here paves the way for development of advanced estimation techniques that can facilitate design of powerful and robust detection algorithms     

Reduced-rank STAP for high PRF radar

Due to the range ambiguity of high pulse-repetition frequency (HPRF) radars, echoes from far-range fold over near-range returns. This effect may cause low Doppler targets to compete with near-range strong clutter. Another consequence of the range ambiguity is that the sample support for estimating the array covariance matrix is reduced, leading to degraded performance. It is shown that space-time adaptive processing (STAP) techniques are required to reject the clutter in HPRF radar. Four STAP methods are studied in the context of the HPRF radar problem: low rank approximation sample matrix inversion (SMI), diagonally loaded SMI, eigencanceler, and element-space post-Doppler. These three methods are evaluated in typical HPRF radar scenarios and for various training conditions, including when the target is present in the training data     

Reiterative median cascaded canceler for robust adaptive array processing

A new robust adaptive processor based on reiterative application of the median cascaded canceler (MCC) is presented and called the reiterative median cascaded canceler (RMCC). It is shown that the RMCC processor is a robust replacement for the sample matrix inversion (SMI) adaptive processor and for its equivalent implementations. The MCC, though a robust adaptive processor, has a convergence rate that is dependent on the rank of the input interference-plus-noise covariance matrix for a given number of adaptive degrees of freedom (DOF), N. In contrast, the RMCC, using identical training data as the MCC, exhibits the highly desirable combination of: 1) convergence-robustness to outliers/targets in adaptive weight training data, like the MCC, and 2) fast convergence performance that is independent of the input interference-plus-noise covariance matrix, unlike the MCC. For a number of representative examples, the RMCC is shown to converge using ~ 2.8N samples for any interference rank value as compared with ~ 2N samples for the SMI algorithm. However, the SMI algorithm requires considerably more samples to converge in the presence of outliers/targets, whereas the RMCC does not. Both simulated data as well as measured airborne radar data from the multichannel airborne radar measurements (MCARM) space-time adaptive processing (STAP) database are used to illustrate performance improvements over SMI methods.     

Circular array STAP

Traditionally, space-time adaptive processing (STAP) for airborne early warning (AEW) radar has been applied to uniform linear arrays (ULAs). However, when considering the overall radar system, electronically scanned circular arrays have advantages: a better combination of even and continual angular and temporal coverage, and mechanical simplicity because it does not need to rotate. This paper answers the question “How well does STAP perform when applied to a circular array?” This paper shows that for the AEW mission, circular arrays are indeed STAP compatible. However, when conventional STAP algorithms are used there may be a small loss in performance when compared with a ULA. With some care in the choice and implementation of the STAP algorithm, the majority of the degradation is at close ranges, where the target returns are relatively strong. At long ranges performance is barely affected. A STAP algorithm which compensates for the circular array environment and provides better performance than existing algorithms is presented     

Adaptive cancellation method for geometry-induced nonstationary bistatic clutter environments

This paper describes and characterizes a new bistatic space-time adaptive processing (STAP) clutter mitigation method. The approach involves estimating and compensating aspects of the spatially varying bistatic clutter response in both angle and Doppler prior to adaptive clutter suppression. An important feature of the proposed method is its ability to extract requisite implementation information from the data itself, rather than rely on ancillary - and possibly erroneous or missing - system measurements. We justify the essence of the proposed method by showing its ability to align the dominant clutter subspaces of each range realization relative to a suitably chosen reference point as a means of homogenizing the space-time data set. Moreover, we numerically characterize performance using synthetic bistatic clutter data. For the examples considered herein, the proposed bistatic STAP method leads to maximum performance improvements between 17.25 dB and 20.75 dB relative to traditional STAP application, with average improvements of 6 dB to 10 dB.     

机载MIMO雷达空时自适应杂波对消器

针对机载多输入多输出(MIMO)雷达杂波分布呈现空时耦合特性,提出一种空时自适应杂波对消器.利用机载MIMO雷达的脉冲回波数据,构造杂波对消器的系数矩阵.通过空时自适应杂波对消器的预处理,可以有效地抑制杂波,并通过与常规空时处理算法的级联,最终可以有效提高动目标的检测性能.实现了由传统地基雷达杂波对消器向机载运动平台的推广.仿真结果表明,这种自适应杂波对消器不仅适用于正侧视雷达,对于非正侧视雷达也同样适用.     

NEW METHOD FOR REDUCED RANK STAP—NON CLUTTER CHANNEL METHOD

Space- time adaptive processing(STAP) is aleading technology candidate for improving detec-tion performance of advanced airborne early warn-ing radar.In practical radar systems,the optimumfully adaptive space- time processing[1] cannot al-ways be implemented because of the computationalcomplexity,so the design of suboptimum proces-sors has been one of the key topics in STAP.Sev-eral reduced- rank STAP methods have been pro-posed in recent years.For example,based on thegeneralized sidelobe…     

Comparison between monostatic and bistatic antenna configurationsfor STAP

The unique characteristics of bistatic radar operation on the performance of airborne/spaceborne moving target indicator (MTI) radars that use space-time adaptive processing (STAP) are discussed. It has been shown that monostatic STAP radar has the following properties. 1) For a horizontal flight path and a planar Earth the curves of constant clutter Doppler (isodops) are hyperbolas. 2) For a sidelooking antenna geometry the clutter Doppler is range independent. 3) Clutter trajectories in the cosφ-F plane (F=normalized Doppler) are in general ellipses (or straight lines for a sidelooking array). We demonstrate that these well-known properties are distorted by the displacement between transmitter and receiver in a bistatic configuration. It is shown that even for the sidelooking array geometry the clutter Doppler is range-dependent which requires adaptation of the STAP processor for each individual range gate. Conclusions for the design of STAP processors are drawn