具有效率优化计算的异步电动机自抗扰与滑模直接转矩控制

为了克服异步电动机直接转矩控制中转矩和电流脉动大等缺点,设计改进的自抗扰速度控制器取代传统的比例积分(PI)控制器。根据异步电动机的数学模型以及滑模变结构控制理论设计了一种基于转矩误差和磁链平方误差的新型滑模控制器。考虑电机运行过程中负载转矩未知问题,设计了一种基于Supertwisting算法的负载转矩观测器。Supertwisting定子磁链观测器的应用提高了观测精确度。通过效率优化计算得出稳态时最优定子磁链,并将其引入调速系统。仿真试验结果表明,该控制策略有效地减小了转矩和电流脉动,并且对外部扰动具有较强抑制作用,同时能够降低电机运行损耗,具有良好的动态和稳态性能。     

基于滑模观测器位置检测的水下推进器直接转矩控制研究

水下推进器是水下航行器的重要组成部分,为提高其转矩响应性能,提出了一种基于滑模观测器位置检测的水下推进器直接转矩控制方法。该方法将一种双曲正切函数引入线反电动势(EMF)滑模观测器,并将该滑模观测器应用于水下推进器直接转矩控制系统中,使得驱动控制系统通过水下推进器线反电动势观测值进行扇区判别与转矩估计,从而获得6个离散的换相信号,实现无位置检测的水下推进器直接转矩控制。仿真试验表明:所提控制方法能够很好地观测线反电动势,提高转矩动态响应,减小系统抖振幅度。     

基于改进型趋近律与负载观测器的永磁同步电机滑模速度控制器设计

为了提高三相永磁同步电机(PMSM)调速系统的动态品质,改善传统滑模速度控制器的控制性能,抑制系统抖振,提高控制精度,设计了基于新型趋近律与负载观测器的改进型滑模速度控制器。利用MATLAB/Simulink仿真软件,搭建控制系统模型并进行仿真分析。仿真验证了所设计的改进型PMSM速度控制器的有效性。该控制器可获得较好的速度跟踪精度和抗负载扰动能力,提高系统的稳定性和鲁棒性。     

电力机车PMSM自适应模糊滑模控制

为研究牵引工况下电力机车永磁同步电机(PMSM)的转速控制精度,考虑轮轨接触不平顺及车体静载荷在轮对径向产生的未知时变负载转矩,建立了机车PMSM在dq坐标系下的数学模型。针对该耦合非线性系统中存在的负载转矩,设计非线性转矩观测器对其实际值进行估计,对观测误差采用自适应模糊逻辑系统进行逼近;为考察d轴电压过零跳变对转速控制及转矩观测性能的影响,在d轴电压控制器设计中引入Nussbaum函数,并依据Lyapunov稳定性理论,构造了基于转矩观测器的自适应模糊滑模控制器。理论分析及仿真结果表明,当转矩时变或d轴电压过零时,机车PMSM闭环转速控制系统跟踪误差一致有界,转矩观测误差收敛于0。     

基于滑模变结构和扩张状态观测器的电动舵机复合控制方法

为提高电动舵机伺服系统的鲁棒性,同时解决实际工作中电动舵机不确定负载引起的跟踪精度低的问题,提出了一种采用指数趋近率的滑模变结构控制率结合扩张状态观测器对负载扰动进行实时估计的电动舵机的伺服控制方法,给出了控制器设计方法和试验验证。仿真和试验结果表明,与常规的滑模控制器相比,采用扩张状态观测器的变结构控制能有效提高电动舵机的跟踪性能。     

基于降维负载转矩观测器的永磁同步电机转矩前馈补偿策略

针对飞机电蒸发冷却系统中永磁同步电机(PMSM)在不同工况下的抗负载扰动问题,研究了负载转矩前馈的方法,提出了一种基于降维负载转矩观测器的转矩前馈控制难点。针对降维负载转矩观测器提出工程化设计方法,通过将观测到的负载转矩补偿到电机电流环输入,实现电机对负载扰动的快速响应,提高了抗负载扰动能力。仿真和试验结果验证了降维负载转矩观测器设计方法以及PMSM负载转矩前馈控制算法的正确性和有效性。     

基于混合终端滑模观测器的永磁同步电机位置和速度估计方法

传统滑模观测器受固有抖振特性影响,且有低通滤波器带来的反电动势观测幅值削弱和观测相位偏移,从而导致永磁同步电机(PMSM)控制精度降低。为解决该问题,提出了一种基于二阶混合终端滑模观测器的PMSM位置和速度估计方法。基于线性滑模与混合终端滑模的二阶滑模切换面,设计合理的滑模控制律,有效抑制传统滑模方法的固有抖振特性,并且能够避免使用低通滤波器所带来的反电动势观测幅值削弱和相位偏移问题,有效提高转子位置和转速的估计精度。在此基础上,进一步分析了该滑模观测器对于电机定子电阻和电感参数摄动的鲁棒性。试验结果证明了所提混合终端滑模观测器的有效性、实用性和优越性。     

电动汽车永磁同步电机滑模低速控制

针对采用永磁同步电机id=0矢量控制调速的电动汽车电机驱动控制系统,为了改善其抗负载扰动能力,并且当电动汽车处于低速运行时,能够输出大转矩,将滑模变结构控制中的变指数趋近律进行改进,设计了一种滑模速度控制器。为了减小滑模变结构控制的抖振问题,引入饱和函数来代替符号函数,同时考虑到滑模速度控制器中存在滞后问题,将饱和函数与经过积分环节后得到的信号相乘,在提高了响应速度的同时增强系统的抗扰动能力。经过仿真验证,不同负载工况下,滑模速度控制器具有较强的鲁棒性和抗扰动能力,满足电动汽车低速运行工况下输出大转矩的要求。     

基于非线性抗扰滑模控制的永磁同步电机直接转矩控制

针对永磁同步电机(PMSM)内部参数不确定和外部干扰未知的问题,提出了一种基于非线性光滑扩张状态观测器(ESO)的非线性控制方法。通过引入非线性光滑函数设计了ESO,实现了对PMSM内部和外部不确定因素的观测,并把观测结果实时补偿给非线性控制器,有效提高了电机的动静态性能和抗扰能力。采用基于非线性光滑函数的滑模控制器替代传统直接转矩控制中的滞环控制器,有效地削弱了转矩和磁链的抖振和脉动。仿真结果表明所提方法响应速度快、稳定性好、抗扰能力强,是一种鲁棒性强的控制方法。     

基于改进型滑模观测器的永磁同步电机分数阶微积分滑模控制

为了提高永磁同步电机调速系统的控制性能,结合滑模控制与分数阶微积分理论,设计了分数阶积分滑模转速控制器和改进型滑模观测器。针对转速控制器,采用基于反双曲正弦函数的新型趋近律削弱系统抖振,同时分数阶控制为系统提供了更多的控制余度,可以增强系统鲁棒性并进一步减小系统抖振。针对观测器,设计了采用新型趋近律fal函数的滑模观测器来获取反电动势估计值,利用分数阶锁相环技术提取反电动势中的转速和位置信息,有效提高了转子速度和位置的估计精度。通过仿真验证了所提出方法的可行性与有效性。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.