鸭式旋翼/机翼飞机悬停状态飞行动力学特性

针对鸭式旋翼/机翼(Canard Rotor/Wing,CRW)飞机独特的气动布局,常规的分析方法及经验公式很难准确地对CRW飞机进行飞行动力学研究,通过飞行辨识对CRW飞机悬停状态特性进行了研究。首先,设计了飞行试验并获得了高质量的飞行数据,基于频率响应对CRW飞机的状态空间模型进行了简化。然后,在频域内对飞机的动力学参数进行了拟合优化,获得了CRW飞机悬停状态的动力学模型,并用飞行数据对所建模型进行了验证。最后,用辨识所得参数与常规直升机悬停状态时的参数进行了对比。结果显示悬停时CRW飞机的操纵导数和阻尼导数均比常规直升机小,经分析,操纵导数的减小主要是CRW飞机独特的旋翼设计所致,阻尼导数减小的原因主要是旋翼气动影响以及鸭翼、平尾、垂尾的结构影响。动力学特性分析结果为CRW飞机旋翼模式总体设计的进一步优化提供了指引和参考,所建立的模型可用于控制系统设计。     

旋转机翼飞机旋翼模式前飞状态干扰气动特性

和传统直升机相比,旋转机翼（CRW）飞机在旋翼模式前飞时各部件之间存在更为严重的气动干扰。为了获得旋转机翼/机身/鸭翼/平尾之间的非定常气动干扰规律,基于运动嵌套网格技术,通过求解三维非定常雷诺平均Navier-Stokes（URANS）方程,建立了旋翼前飞流场数值模拟方法。首先对传统直升机旋翼/机身干扰模型进行了计算,验证了方法的可靠性,然后对某旋转机翼飞机全机在旋翼模式前飞状态下的非定常流场进行了数值模拟,并对各个气动部件上的非定常气动力和力矩的变化进行了分析。结果表明：飞机在旋翼模式前飞时,机身部件对旋转机翼的干扰较弱,在经过机身上方时拉力峰值仅略有增加;旋转机翼对鸭翼和垂尾干扰较弱,对机身和平尾干扰较强,随着前飞速度增大,旋转机翼对平尾的干扰会产生较大的升力损失和抬头力矩,需要引起重视。计算结果为该类飞行器的总体综合设计提供了参考。     

鸭式旋翼/机翼无人机飞行动力学建模与分析

针对鸭式旋翼/机翼无人机兼有直升机和固定翼机飞行特性的特点,对其飞行动力学模型进行了理论建模与分析研究。应用动量理论建立了旋翼/机翼尾迹模型,分析了旋翼/机翼尾迹对鸭翼、平尾等气动部件的干扰特性,建立了直升机和转换飞行模式受旋翼/机翼尾迹干扰影响的动力学模型以及固定翼飞行模式的动力学模型。提出了各飞行模式的配平策略,使用Matlab工具箱函数简化了平衡特性计算和模型线性化过程,并进行了不同飞行模式、典型飞行状态的纵向运动稳定性分析。结果表明所建立的模型能够反映该类鸭式旋翼/机翼无人机各飞行模式的典型特性,并可用于飞行控制系统设计。     

倾转旋翼飞行器的建模和操纵分配策略

针对倾转旋翼飞行器试飞样机建立了旋翼、机翼、短舱、机身、平尾、垂尾等部件的非线性气动模型和飞行动力学模型,研究了直升机模式、倾转过渡模式和飞机模式下的操纵特性,根据配平分析和小扰动线性化处理结果得到了不同飞行模式下的操纵效率,提出了一套适用于全飞行模式的操纵分配策略,解决了飞行控制随飞行模式变化出现的气动结构部件变化与操纵冗余的难题.利用所提出的操纵分配策略可使飞行控制器统一设计,无需按不同飞行模式设计不同控制律,有效降低了飞行控制器的设计难度.仿真验证了倾转旋翼飞行器飞行动力学模型的可信性和操纵分配策略的有效性.      

倾转旋翼飞行器飞行力学模型研究

对倾转旋翼飞行器飞行力学模型的建立进行了理论研究.其中旋翼的气动模型,使用了非定常叶素理论,而对于机翼、尾翼和机身的气动力计算则采用了成熟的升力线理论模型.对于气动干扰的问题,则主要是考虑了机翼与旋翼的气动干扰.最后对算例飞行器不同模式下的飞行状态进行了飞行特性计算,验证了所建模型的合理性.     

Aeroservoelastic modeling and analysis of a canard-configured air-breathing hypersonic vehicles

Air-breathing hypersonic vehicles (HSVs) are typically characterized by interactions of elasticity, propulsion and rigid-body flight dynamics, which may result in intractable aeroservoelastic problem. When canard is added, this problem would be even intensified by the introduction of low-frequency canard pivot mode. This paper concerns how the aeroservoelastic stability of a canard-configured HSV is affected by the pivot stiffnesses of all-moveable horizontal tail (HT) and canard. A wing/pivot system model is developed by considering the pivot torsional flexibility, fuselage vibration, and control input. The governing equations of the aeroservoelastic system are established by combining the equations of rigid-body motion, elastic fuselage model, wing/pivot system models and actuator dynamics. An unsteady aerodynamic model is developed by steady Shock-Expansion theory with an unsteady correction using local piston theory. A baseline controller is given to provide approximate inflight characteristics of rigid-body modes. The vehicle is trimmed for equilibrium state, around which the linearized equations are derived for stability analysis. A comparative study of damping ratios, closed-loop poles and responses are conducted with varying controller gains and pivot stiffnesses. Available bandwidth for control design is discussed and feasible region for pivot stiffnesses of HT and canard is given.     

倾转四旋翼飞行器垂直飞行状态气动特性

综合采用基于滑移网格技术的计算流体力学(CFD)方法与悬停状态气动干扰试验方法,对倾转四旋翼(QTR)飞行器垂直飞行状态的流场进行模拟与试验,研究飞行器垂直飞行状态气动特性以及部分参数对气动特性的影响.结果表明:倾转四旋翼飞行器在垂直飞行状态,前后旋翼之间干扰不明显,但旋翼与机翼的干扰明显;旋翼旋向对旋翼与机翼的干扰不...     

倾转旋翼飞行器旋翼对机翼向下载荷计算模型

针对倾转旋翼飞行器悬停和小速度前飞的直升机飞行模式下旋翼下洗流对机翼的气动干扰影响,建立了一个机翼向下载荷的计算模型.该模型中,最关键的是建立旋翼对机翼的气动干扰面积模型.此模型考虑了倾转旋翼飞行器几何尺寸条件、发动机短舱倾转角和飞行状态等参数.最后将此模型集成到XV-15倾转旋翼飞行器飞行动力学模型中,进行配平计算,...     

Time-varying linear control for tiltrotor aircraft

Tiltrotor aircraft have three flight modes: helicopter mode, airplane mode, and transition mode. A tiltrotor has characteristics of highly nonlinear, time-varying flight dynamics and inertial/control couplings in its transition mode. It can transit from the helicopter mode to the airplane mode by tilting its nacelles, and an effective controller is crucial to accomplish tilting transition missions. Longitudinal dynamic characteristics of the tiltrotor are described by a nonlinear Lagrange-form model, which takes into account inertial/control couplings and aerodynamic interferences. Reference commands for airspeed velocity and attitude in the transition mode are calculated dynamically by visiting a command library which is founded in advance by analyzing the flight envelope of the tiltrotor. A Time-Varying Linear (TVL) model is obtained using a Taylor-expansion based online linearization technique from the nonlinear model. Subsequently, based on an optimal control concept, an online optimization based control method with input constraints considered is proposed. To validate the proposed control method, three typical tilting transition missions are simulated using the nonlinear model of XV-15 tiltrotor aircraft. Simulation results show that the controller can be used to control the tiltrotor throughout its operating envelop which includes a transition flight, and can also deal with vertical gust disturbances.     

基于拉格朗日方程的倾转旋翼机动力学建模

针对倾转短舱与机体间的气动干扰和惯性耦合特征,基于拉格朗日原理推导出了倾转旋翼机的纵向飞行动力学方程。在此基础上,以XV-15倾转旋翼机为对象,针对几种不同的短舱倾角,计算分析了飞行器的配平特性和过渡模式动态响应特性。仿真结果表明,所建立的动力学模型是合理的。该模型可用于研究倾转旋翼机的直升机飞行模式、飞机飞行模式及过渡飞行模式下的纵向飞行特性。     

前翼对飞机纵向气动特性和机翼载荷影响研究

利用ARGON和MGAERO计算了三翼面布局飞机气动特性和机翼载荷,给出了有前翼、无前翼布局全机气动特性和机翼环量分布。研究分析了前翼对全机气动特性、机翼分布载荷的影响规律,得到了一些重要的结论,可用于飞机型号设计。     

Sliding mode control design for oblique wing aircraft in wing skewing process

When the wing of Oblique Wing Aircraft (OWA) is skewed, the center of gravity, inertia and aerodynamic characteristics of the aircraft all significantly change, causing an undesirable flight dynamic response, affecting the flying qualities, and even endangering the flight safety. In this study, the dynamic response of an OWA in the wing skewing process is simulated, showing that the three-axis movements of the OWA are highly coupled and present nonlinear characteristics during the wing skewing. As the roll control efficiency of the aileron decreases due to the shortened control arm in an oblique configuration, the all-moving horizontal tail is used for additional roll and the control allocation is performed based on minimum control energy. Given the properties of pitch-roll-yaw coupling and control input and state coupling, and the difficulty of establishing an accurate aerodynamic model in the wing skewing process due to unsteady aerodynamic force, a multi-loop sliding mode controller is formulated by the time-scale separation method. The closed-loop simulation results show that the asymmetric aerodynamics can be balanced and that the velocity and altitude of the aircraft maintain stable, which means that a smooth transition is obtained during the OWA’s wing skewing.     

Full mode flight dynamics modelling and control of stopped-rotor UAV

The Stopped-Rotor(SR) UAV combines the advantages of vertical take-off and landing of helicopter and high-speed cruise of fixed-wing aircraft. At the same time, it also has a unique aerodynamic layout, which leads to great differences in the control and aerodynamic characteristics of various flight modes, and brings great challenges to the flight dynamics modelling and control in full-mode flight. In this paper, the flight dynamics modelling and control method of SR UAV in full-mode flight is st...     

计入螺旋桨干扰的倾转机翼飞行器气动特性研究

倾转机翼飞行器不仅拥有直升机固有的垂直起降能力,还具备传统固定翼飞行器特有的高速巡航的特点,是目前军民用飞行器研究的热点之一。针对传统倾转机翼飞行器存在螺旋桨气动效率低、倾转机构复杂的问题,提出四发串列式倾转机翼垂直起降布局形式,对该布局飞行器进行总体设计,完成螺旋桨周围流场特性、螺旋桨间干扰特性、螺旋桨和机翼之间干扰特性的研究分析,并制作验证机进行验证。结果表明:该布局很好地解决了螺旋桨气动效率低、传动机构复杂的问题,具有较强的可实现性及实用性。     

共轴式直升机全差动航向操纵的动态响应分析

运用经典的垂直飞行涡流理论及共轴双旋翼全差动操纵的结构特征，推导了共轴式双旋翼直升机垂直飞行的航向动力学方程。根据有关共轴双旋翼在悬停及垂直飞行状态时气动特性的理论和实验数据，得出了共轴双旋翼直升机垂直飞行航向动力学方程的解析式。某型共轴双旋翼直升机计算实例，所得结果与该型直升机飞行特性一致。     

Investigation of Vortex Interaction in Canard-FSW Configurations Based on the Numerical Wind Tunnel Method

The vortex interference mechanism on low Reynolds number between the canard and main wing of the canard-forward sweep wing (Canard-FSW) configurations is simulated numerically by employing the numerical wind tunnel method. The variations of aerodynamic characteristics of Canard-FSW configurations with different positions of the canard are investigated, finding that the aerodynamic interference and mutual coupling effect between the canard and main wing have made great contributions to the lift and stability characteristics of the whole aircraft. Canard can radically improve the surface flow pattern of the main wing. And its own vortex can have a favorable interference on the main wing and can effectively control the airflow boundary layer separation. At small angles of attack, the aerodynamic characteristics are sensitive to the positions of the canard and the main wing, but at high angles of attack, the aerodynamic performances of the configuration are not only related to the shape of the canard (forward or backward), but also with the size of control force as well as the features of the vortices generated above the main wing and the canard. The different configurations and vortices are illustrated using the velocity vector, streamlines and pressure contours.     

折叠翼变体飞行器非定常气动特性实验研究

折叠翼变体飞行器是一种可以在飞行中改变自身气动外形的新型飞行器。研制出了一种折叠翼变体飞行器的风洞实验模型,在风洞实验中测得了模型不同变体位置下的气动力以及进行变体运动时气动力的动态变化过程,并通过PIV实验手段获得模型周围的流场在变体运动过程中的变化情况。结果表明：在机翼变形过程中,折叠翼模型有明显的非定常气动现象产生,而且折叠变形的速度越大,非定常现象越明显。出现非定常现象的主要原因是变体运动对机翼前缘涡的影响。     

鸭翼-前掠翼气动布局纵向气动特性实验研究

前掠翼布局由于其潜在的优势,在未来战斗机的研制中将占有日益重要的地位.本实验通过可变前掠翼和鸭式前翼布局的风洞测力实验,重点分析比较了平板机翼在不同掠角下的纵向气动性能以及鸭翼的影响.实验结果表明,前掠翼在大迎角时能有效提高模型的升力系数,小迎角时其升阻比也略优于后掠翼.前掠翼布局能有效推迟失速,具有良好的失速特性;前掠角较大时,升力系数曲线在失速迎角附近有一个升力系数的"平台",该布局具有"缓失速"特性.距离主机翼较远的鸭式前翼(模型M2)在主机翼前掠和后掠情况下,均可改善整体布局的失速特性,增大失速迎角,增强前掠翼布局缓失速的特点.近距耦合鸭翼(模型M3)显著提高了模型在大迎角下的升力系数.另外,主翼前掠和鸭式前翼布局飞行器具有较好的机动性.     

直升机飞行动力学数学建模问题

直升机飞行动力学数学模型是飞行控制系统设计的基础,也是直升机飞行品质设计和评估的主要手段。直升机是一个多体系统,在直升机飞行动力学建模过程中,必须考虑旋翼、机体与升力面等的运动耦合、惯性耦合、结构耦合和气动耦合以及非定常、非线性特性,给出各个运动部件的物理模型及其数学表达形式,是对不同假设、子模型进行分析和综合的一个复杂的过程。鉴于此,简要回顾了单旋翼带尾桨直升机飞行动力学数学模型的研究现状,着重描述了直升机飞行动力学数学建模中的旋翼气动力建模、直升机气动干扰建模、旋翼/发动机建模以及直升机飞行动力学模型的集成与综合的研究现状与研究进展。最后,针对直升机飞行动力学的数学建模提出了今后的研究重点。     

倾转旋翼飞行器发动机短舱 倾转角度 -速度包线分析

针对倾转旋翼飞行器过渡飞行中的变体、变速特点提出了一种确定倾转旋翼飞行器从直升机模式向固定翼飞机模式过渡的发动机短舱倾转角度-速度包线分析方法.该方法从低速段包线和高速段包线两方面开展研究,分析倾转过程中旋翼和机翼的气动力匹配关系,以机翼失速限制确定低速段的发动机短舱倾转角度-速度包线,以旋翼可用功率限制确定高速段的发动机短舱倾转角度-速度包线.最后以XV-15倾转旋翼飞行器为样机,计算分析其发动机短舱倾转角度-速度包线,并与XV-15的发动机短舱倾转角度-速度包线进行对比验证.结果表明,建立的倾转旋翼飞行器发动机短舱倾转角度-速度包线确定方法合理有效.