一种镍基单晶和定向结晶合金的疲劳寿命模型

针对镍基单晶和定向结晶合金的高温低循环疲劳/蠕变寿命预测问题,用晶向函数修正总应变范围以考虑疲劳寿命的各向异性,并综合考虑了最大应力、平均应力、应力范围以及峰值保持等载荷因素对寿命的贡献,在循环损伤累积思想的基础上发展了一种低循环疲劳/蠕变寿命预测方法.利用定向结晶合金DZ125、单晶合金DD3和DD6在不同温度、不同取样方向和不同保载形式作用下的试验结果,对方法进行了验证,预测与试验寿命相比基本落在2倍分散带内,表明该方法能更好地适应叶片材料各向异性与低循环疲劳/蠕变载荷的情况.      

含孔薄板孔边疲劳裂纹的萌生和扩展

 测试了 Ni基高温合金 GH41 69含孔薄板试件不同应力幅下的低周疲劳寿命,给出了孔边最大应力幅相同时,应力集中因子改变对试件疲劳寿命的影响。结合断口 SEM分析,探讨了应力集中条件下,疲劳短裂纹的萌生和扩展方式。试验结果表明,疲劳裂纹以滑移方式在孔壁与试样表面相交的棱上萌生;萌生期依赖于孔边应力幅的大小,与孔径无关。但疲劳裂纹扩展速率与孔边局部区域的应力分布有关。在孔边应力幅相同的情况下,孔边应力集中因子较大的试样裂纹扩展速率大,疲劳寿命分布带略低于孔边应力集中因子较小的试样。短裂纹阶段,疲劳裂纹以角裂纹的形式向内扩展;长裂纹阶段,疲劳裂纹以穿透裂纹的形式进行扩展。稳定扩展阶段疲劳裂纹以穿晶的韧性撕裂方式发展,但在靠近失稳扩展区域疲劳裂纹呈准解理断裂方式扩展。试验未观察到疲劳短裂纹群的连接与合并现象。     

抽拉速率对DD6单晶高温合金650℃低周疲劳性能的影响

采用2mm/min,4.5mm/min和7mm/min的抽拉速率制备了DD6单晶高温合金试棒。研究了抽拉速率对合金650℃低周疲劳性能的影响。利用扫描电镜(SEM)和透射电镜(TEM)分析了疲劳试样的断口形貌和微观组织。研究结果表明:随抽拉速率的增大,γ’相尺寸减小,一次枝晶间距差异不大,二次枝晶呈发达的趋势。抽拉速率4.5mm/min的合金650℃低周疲劳寿命最长。DD6合金表现为基本稳定的循环应力响应行为。疲劳裂纹主要萌生于试样亚表面,随应变量降低,裂纹扩展第一阶段断裂特征由类解理断裂面向锯齿状断面转变。疲劳裂纹沿一个或者多个{111}滑移面扩展。     

基于细观位错机理的单晶合金高温力学性能模拟

利用基于细观位错运动的蠕变筏化模型对镍基单晶合金CMSX-4在1223K下的拉伸、蠕变、循环、蠕变疲劳交互及各向异性进行模拟,结果表明:拉伸过程中应变率较高时应力略微下降的现象;蠕变条件下应力越大则蠕变第1阶段越明显,而蠕变稳定阶段越短的趋势;蠕变疲劳交互作用下的应力松弛和应变增大;以及单晶3个典型晶体取向的循环应变硬化特征。通过与试验结果对比,验证了此模型在较高温度下对单晶合金性能的综合模拟能力。     

GH3044的高温低周疲劳性能研究

研究了镍基高温合金GH3044在600℃下的低周疲劳性能,分析了合金的循环应力-应变和应变-寿命关系,利用Manson-Coffin方程、三参数幂函数方程和拉伸滞后能模型对寿命数据进行回归分析。结果表明,合金的循环应力响应行为在600℃时,呈现明显的循环硬化特征,原因在于循环变形过程中位错之间以及位错与析出相之间的相互作用;从试样的疲劳断口形貌发现,裂纹主要萌生于试样表面处,裂纹形成后垂直于加载轴方向扩展,断口呈韧窝断裂特征;在合金的低周疲劳寿命预测研究中发现,拉伸滞后能模型的寿命预测结果无论从标准差,还是分散带方面比较都比Manson-Coffin方程、三参数幂函数方程的预测精度好。     

热处理对AZ80镁合金疲劳性能的影响

通过对AZ80镁合金进行总应变幅控制下的室温低周疲劳实验,研究其在热锻、时效态(T5)、固溶时效态(T6)三种不同热处理状态下的循环应力响应、疲劳寿命和循环应力-应变行为。结果表明:在三种不同的热处理制度下,AZ80镁合金大体上都表现为循环应变硬化现象;此外,AZ80镁合金的应变疲劳寿命与塑性应变幅、弹性应变幅之间的关系分别服从Coffin-Manson和Basquin关系式。随着外加总应变幅的不断增大,其疲劳寿命减少。在0.3%的最小外加总应变幅下,AZ80热锻态的疲劳寿命最长;在0.9%的最大外加总应变幅下,AZ80-T5的疲劳寿命最长,而热锻态最短。此外,对疲劳断口形貌的观察结果表明,疲劳裂纹萌生于疲劳试样表面,并以穿晶方式扩展。     

涡轮盘用IN718合金的高温低周疲劳及其裂纹扩展特性

研究了IN718合金在360℃、550℃和650℃下的低周疲劳行为及疲劳裂纹扩展速率da/dN,包括循环应力-应变行为、Massing效应、低周疲劳寿命的能量表达以及疲劳裂纹扩展速率,并讨论了保持时间对da/dN的影响。实验结果表明,该合金在各种温度下表现出循环软化,在本文所试温度下具有Massing特性,其塑性应变能与疲劳寿命在双对数坐标中呈现出很好的线性关系,其da/dN随温度的升高而增大,在650℃下保持时间对da/dN的影响很明显,而550℃时则很轻微。     

一种修正的应变范围区分法

针对高强度、低延性材料非弹性应变范围小、难以区分的特点,提出一种修正的应变范围区分方法。该方法不区分非弹性应变中的塑性和蠕变,定义了3种基本类型的非弹性应变范围,即拉伸塑性-压缩塑性非弹性应变范围、拉伸塑性和蠕变-压缩塑性非弹性应变范围和拉伸塑性-压缩塑性和蠕变非弹性应变范围。对同时包含拉/压蠕变的循环,采用线性累积损伤法则预测其寿命。用Rene’95材料650℃下控制应变的循环松弛试验数据对修正方法进行了验证,结果表明:对Rene’95材料的蠕变疲劳寿命,修正方法的预测能力好于应变范围区分法(SRP),对基本试验的寿命预测精度基本上在2倍范围之内。      

AZ31B镁合金大应变循环变形行为研究

为了研究AZ31B镁合金在大应变幅条件下的变形机制,开展了该合金在7.嬲应变幅条件下的循环行为研究.结果表明:在拉伸阶段的最大应力值随着循环周次的增加而减小,而在压缩过程中的最大应力值随着循环周次的增加而增大,在整个循环过程中材料呈现循环应变硬化特性,拉应力是导致循环应变硬化的主要原因;随着循环周次增加,滞回曲线的不对称性基本不变.真应力-真应变滞回曲线在卸载和反向拉伸阶段出现3个拐点.在压缩过程中发生{10-12}孪生,反向拉伸过程发生去孪生行为,包申格效应对去孪生行为具有较大影响.研究表明:孪生-去孪生是大应变幅循环变形的主要变形机制;对拉伸、反向压缩过程的变形特征及机制的分析,可为低周疲劳行为的研究提供参考.     

定向凝固DZ4合金的低周疲劳行为与稳定循环应力

对定向凝固DZ4合金760℃和800℃下的低周疲劳和稳定循环应力应变行为进行了研究,并结合断口观察试验结果,对其疲劳裂纹的萌生与扩展进行了分析。结果表明,DZ4合金760℃和800℃下的低周疲劳属应力疲劳,其损伤以弹性损伤为主,弹性损伤与疲劳寿命具有很好的相关性。加载频率对DZ4合金760℃和800℃下的稳定循环应力均具有一定的影响,尤其是800℃时,各应变下的稳定循环应力均随加载频率的升高而减小。定向凝固DZ4合金高寿命低周疲劳裂纹易于萌生于试样内部或亚表面的柱状晶界,其疲劳裂纹的稳定扩展也较难形成典型的疲劳条带。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.