高速电弧喷涂FeCrAl涂层组织结构及抗高温氧化性能研究

用高速电弧喷涂技术(HVAS)制备FeCrA l涂层,测试涂层在800℃的氧化性能,研究涂层在喷涂态和氧化后的组织结构。结果表明,由于冷却速率极快,FeCrA l涂层中形成比较多的Fe-Cr非晶态相,还有少量的Cr1.3Fe0.7O3和体心立方晶格的Fe-Cr固溶体,喷涂过程中A l的氧化比较严重。FeCrA l涂层的抗高温氧化性明显高于12Cr1MoV钢,接近于T91钢,涂层具有优异的抗氧化性一方面是由于层片间形成保护性的Cr氧化膜,阻止进一步氧化,也与含有较多抗氧化性好的非晶态相有关。高温氧化后,涂层中部分非晶态相晶化,转变为Fe-Cr晶体相。     

真空预氧化处理对热障涂层静态氧化行为的影响

利用超音速火焰喷涂技术在DZ40M合金表面制备了Ni Co Cr Al Y粘结层,采用等离子喷涂技术在粘结层表面制备了陶瓷面层,并对整体热障涂层进行了真空预氧化处理。通过高温静态氧化实验研究了真空预氧化对热障涂层的氧化行为的影响。结果表明:真空预处理可在MCr Al Y粘结层和陶瓷面层的界面处形成连续、致密的α-Al2O3层;在1050℃下氧化800h后,喷涂态涂层TGO中除α-Al2O3外,还生成了大量尖晶石氧化物,而预氧化涂层TGO则以α-Al2O3为主;预氧化处理有效抑制了涂层在高温氧化过程中尖晶石氧化物的形成,从而降低了整体氧化膜的生长速率。     

激光熔覆Co—Cr—Al—Y合金显微组织及其抗氧化性能研究

本文用2KW Co_2激光器和同时送给工艺在1Cr18Ni9Ti基体上获得了Co-Cr-Al-Y激光熔覆层。涂层试件的显微组织分析表明,涂层组织主要由γ相,α相和富γ粒子组成。在950℃恒温氧化100小时后,涂层的氧化增重远低于基体试件的氧化增重。抗氧化性的改进是由于富γ质点的钉扎作用。     

TiAl合金高温循环氧化行为及其表面改性研究

研究了TiAl金属间化合物及表面涂层在空气中的高温循环氧化行为。结果表明:在800℃时TiAl合金具有较好的抗高温氧化行为,但当温度高于800℃时,TiAl合金表面未能形成单一的Al2O3保护层,而是形成外3层为疏松的TiO2层,内层为TiO2+Al2O3的混合氧化物层,因而使得TiAl合金的抗高温循环氧化性能严重蜕化。TiAl合金经过Cr改性铝化处理后,表面形成了具有立方Ll2结构的Al67Ti26Cr7层,立方Ll2结构的Al67Ti26Cr7不仅具有较高的铝含量,而且具有优良的韧性,因而使得处理后的TiAl合金具有良好的抗高温循环氧化性能。铝化物涂层尽管有很高的铝含量,但由于铝化得到的TiAl3相具有四方形结构,涂层非常脆,故该涂层抗高温循环氧化性能有待进一步提高。     

高温合金纳米晶涂层的发展

高温合金纳米晶涂层是一种新的高温合金防护涂层体系.与目前通常采用的涂层不同,其成分与基体合金基本相同,有良好的抗氧化性能,且避免了传统涂层高温使用后在涂层与基体间因互扩散形成的脆性有害相.高温合金纳米晶涂层是在研究晶粒度对合金抗氧化性能影响的基础上发展起来的.本文综述了国内外对晶粒细化影响铁基合金、金属间化合物、高温合金等氧化性能的研究概况,重点介绍了高温合金溅射纳米晶涂层的研究结果.     

两种MCrAlY涂层/DD6合金的循环氧化和互扩散行为

在DD6单晶高温合金基体上,利用电子束物理气相沉积(EB-PVD)技术制备Ni Co Cr Al Y涂层,采用低压等离子喷涂(LPPS)技术制备Ni Co Cr Al YHf Si涂层,通过扫描电镜(SEM)、X射线能谱(EDS)、X射线衍射(XRD)、电子探针显微分析(EPMA)等手段研究了在1100℃下的热循环氧化和互扩散行为。结果表明,涂层显著提高了DD6基体的抗氧化能力,经100h的循环氧化后,涂层表面氧化层主要成分仍为α-Al2O3,依然发挥着较好的抗氧化保护作用。这两种涂层与基体之间形成了互扩散区(IDZ)和二次反应区(SRZ),IDZ和SRZ的厚度均随着循环氧化时间延长而增大;SRZ中析出的棒状与颗粒状的拓扑密堆相(TCP)含有W、Re、Mo等高熔点元素,其质量分数分别高达37.51%、14.22%和10.61%,TCP含量随着氧化时间而增多。活性元素Si、Hf对涂层中富Cr相和TGO的增长速率均有一定的抑制作用。     

涡轮叶片热障涂层三维成像研究进展

热障涂层是涡轮叶片高温防护关键技术,具有典型的层状结构特征,且热障涂层服役过程中高温氧化产生热生长氧化物结构,迫切需要利用三维成像方法无损探知热障涂层内部结构.由于计算机断层成像技术能提供三维立体图像,准确再现物体内部三维结构,是热障涂层层状结构最佳分析手段之一,在热障涂层喷涂质量评价和高温氧化监测方面具有很好的前景....     

碳化铬／Ni3Al复合材料的高温抗氧化性能

对比研究碳化铬/Ni3Al复合材料和传统高温耐磨材料Stellite 12合金在1000℃时的高温氧化行为.结果表明,Stellite 12合金表面形成以Cr2O3为主的氧化膜,并发生明显剥落;而碳化铬/Ni3Al复合材料表面形成以α-Al2O3为主的致密氧化膜,其空气中的氧化速率仅为Stellite 12合金的1/2,碳化铬具有良好的抗氧化稳定性并与Ni3Al基体有较好的氧化协同性.分析认为,碳化铬在堆焊过程中发生溶解导致部分Cr固溶于Ni3Al合金基体中,促进α-Al2O3的形成,从而改善复合材料的抗氧化性.而材料表面所形成的氧化膜类型是两种材料抗氧化性差异的主要原因.     

三种热喷涂工艺制备NiCr/Cr_3C_2-BaF_2·CaF_2涂层的结构与性能

采用大气等离子喷涂、爆炸喷涂和超音速火焰喷涂三种热喷涂技术制备了NiCr／Cr3C2-BaF2·CaF2涂层,分析比较了涂层的显微组织、物相组成、孔隙率、硬度、结合强度及其摩擦学性能。结果表明,与大气等离子喷涂相比,超音速火焰喷涂和爆炸喷涂技术制备的涂层具有更高的致密度、硬度和结合强度。采用包覆法制备的粉末进行喷涂,碳化物失碳明显减少,涂层中氧化物含量低。三种NiCr／Cr3C2-BaF2·CaF2热喷涂涂层的摩擦系数都随着温度的升高而减小,爆炸喷涂和超音速火焰喷涂涂层的摩擦系数比等离子喷涂涂层的摩擦系数更低,耐磨性得到提高。高温下BaF2·CaF2润滑膜的形成均可有效降低三种涂层的摩擦系数,从而降低涂层和对磨球Si3N4的磨损率。     

工艺动态

ＣＭ2 47ＬＣ超合金的耐高温腐蚀热障涂层　　德国的Ｉ .Ｇｕｒｒａｐｐａ对燃气涡轮发动机高温零件先喷涂耐腐蚀涂层 ,再喷涂氧化锆基热障涂层 ,以改善其抗氧化性和耐腐蚀性 ,延长零件寿命。在机械加工的直径 10ｍｍ、高 10ｍｍ的ＣＭ 2 4 7ＬＣ超合金试片上 ,用大气等离子喷涂制备各种成分的ＭＣｒＡｌＹ耐腐蚀涂层 ,再在该涂层上喷涂不同厚度的热障陶瓷涂层(8%Ｙ2 Ｏ3稳定的ＺｒＯ2 )。高温腐蚀试验在 90 0℃ ,90 %Ｎａ2 ＳＯ4 + 5%ＮａＣｌ+ 5%Ｖ2 Ｏ5的环境中进行 ,以得出涂层直至破坏的寿命。结果证明 ,热障涂层恶化是由于环境中的钒…     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.