电沉积制备ZrO2／Ni纳米复合材料的超塑性

采用电沉积方法制备了平均晶粒尺寸为45 nm的ZrO2/Ni纳米复合材料,并通过拉伸试验对该材料的超塑性能进行了研究.结果表明:ZrO2/Ni纳米复合材料具有低温高应变速率超塑性,在温度为450℃、应变速率为1.67×10-3/s时,获得的最大伸长率为605%.采用SEM和TEM分析了沉积态材料及变形后的组织,并对变形机理进行了探讨.ZrO2/Ni纳米复合材料的超塑变形机制主要是晶界滑移,S元素的析出在一定程度上协调了变形.     

电沉积ZrO2/Ni纳米复合材料低温高应变速率超塑性的研究

采用电沉积方法制备了平均晶粒尺寸为45nm的ZrO2/Ni复合材料,并通过拉伸和胀形试验对该材料的超塑性能进行了研究。拉伸试验结果表明:材料在温度为420~500℃,应变速率为8.33×10-4s-1~1.67×10-2s-1时均获得了高于200%的延伸率。在温度为450℃和应变速率为1.67×10-3s-1时,得到最大延伸率605%。用扫描电镜SEM对拉伸前后试件的显微组织进行了观察,发现晶粒在温度的作用下明显长大。采用内径5 mm的凹模对ZrO2/Ni复合材料进行超塑胀形试验,在温度为420~500℃获得高径比H/d高于0.5的胀形件,说明该材料具有良好的超塑性能。     

等温锻造FGH96合金超塑性研究

对等温锻造FGH96合金的超塑性进行了研究.研究表明,FGH96合金在变形温度为1050℃和1100℃,初始应变速率ε0为1×10-2s-1～1×10-3s-1的拉伸变形条件下,均呈现出较好的超塑延性.在变形温度为1050℃,初始应变速率为1.67×10-3s-1时,合金超塑延伸率均可以达到825%.微观组织分析表明,FGH96合金超塑拉伸的断裂主要原因是空洞的长大和连接.     

低温预变形对SiC_p/MR64复合材料超塑性的影响

 用拉伸实验研究了低温预变形对碳化硅颗粒增强MR64复合材料超塑性的影响。材料在500℃,应变速率为8.33×10~(-3)s~(-1)的条件下拉伸,超塑变形延伸率达到210％,材料经过300℃低温预拉伸至35％的变形量以后,在超塑条件下拉伸延伸率达305％。通过对显微组织、孔洞的观察发现,低温预变形产生的形变组织在超塑变形初期发生了动态再结晶,晶粒尺寸得到进一步细化,孔洞面积率明显减少。低温预应变提高超塑性的主要原因在于它减少了变形过程中孔洞的数量。     

铝青铜 QAl 10—3—1.5合金超塑性变形的研究

铝青铜 QAl 10-3-1.5合金经超细化预处理工艺后,在830℃以初始应变速率(?)=1.67×10~(-3)s(-1)拉伸,得最高延伸率823%,流动应力23.67MPa。合金在拉伸变形时,其组织由α β δ三相构成;α相较硬,晶粒始终保持微细等轴状,其等轴比在1.01～1.36范围内。显微组织参数恰是微细晶粒超塑性所要求的组织条件。试样的断裂是由于在变形后期,因空洞长大连接所致。     

TC6钛合金超塑性变形

对TC6钛合金在800~900℃温度区间内,分别进行应变速率为0.0001~0.1 s-1的恒应变速率法拉伸实验和最大m值法超塑性拉伸实验,获得拉伸过程应力-应变曲线,并采用金相显微镜对拉伸后断口附近显微组织进行分析。结果表明：TC6合金表现出良好的超塑性性能,随着应变速率或温度的升高,伸长率先增大后减小,恒应变速率拉伸时,在温度850℃、应变速率0.001 s-1条件下伸长率可达到993%;在同一变形温度下最大m值法拉伸能获得比恒应变速率法更好的超塑性,850℃时伸长率达到1353%;TC6合金在超塑性变形过程中发生了明显的动态再结晶,并随着应变速率和温度的升高动态再结晶行为增强。     

喷射沉积SiCp／LY12复合材料的性能及超塑性变形

研究了喷射沉积10Vol％SiCp／LY12复合材料的组织、强度极限该复合材料经热等静压和等温热正挤压后的超塑性。结果表明：喷射沉积的铝基复合材料经过简单的预处理具有良好的超塑性性能，应变速率敏感性指数m值达0．53，极限延伸率达345％。这与良好的组织状态密切相关。在该复合材料的超塑性变表过程中，空洞的形核与长大一直存在，空洞的长大和连接对材料的断裂有重要的影响。     

冷轧态5B70合金超塑性行为研究

为了探究冷轧态5B70合金超塑性行为,利用高温拉伸试验对冷轧板材在不同参数下的变形规律进行研究。结果表明:在初始应变速率为5×10~(-4)～1×10~(-2) s~(-1)和拉伸温度为450～500℃范围内,冷轧5B70合金板材具有良好的超塑性;500℃为合金的最佳超塑性变形温度,1×10~(-3) s~(-1)为最佳初始应变速率,在最佳超塑性条件下合金的最大延伸率达到了670%,应变速率敏感性指数为0.43;在超塑性变形过程中,由于动态再结晶作用,原始纤维组织逐渐转变为等轴晶,并且晶粒明显细化;合金的超塑性变形是再结晶辅助下晶界滑移为主的变形机理,表现出了明显的晶间断裂特征。     

高应变速率超塑性研究的新进展

综述了高应变速率超塑材料及其变形机理和工业应用的最新进展.高应变速率超塑材料主要是铝基复合材料及铝合金,最近,对镁基复合材料、钛合金高应变速率超塑性能的研究也已开始.材料的高应变速率超塑性能使材料可进行超塑性锻造,使得该项技术具有诱人的工业应用前景.     

工业供应态LY12铝合金的超塑性

对工业供应态LY12铝合金棒材的超塑性进行了研究。结果表明 :该合金在温度为 75 3K、应变速率为 3.3× 10 - 4s- 1的拉伸变形条件下 ,断裂延伸率为 313% ,应变速率敏感性指数m值约为 0 .33;断裂延伸率的实验值与Ghosh Ayres公式的理论值吻合 ;超塑性变形的主导机制符合Langdon大晶粒模型     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.