A multioutput LLC-type parallel resonant converter

When an LLC-type parallel resonant converter (LLC-PRC) operates above resonant frequency, the switching transistors can be turned off at zero voltage. Further study reveals that the LLC-PRC possesses the advantage of lower converter voltage gain as compared with the conventional PRC. Based on the analytic results derived, a complete set of design curves from which a systematic design procedure is developed is obtained. Experimental results from a 150-W, 150-kHz, multioutput LLC-type PRC power supply are presented     

Parallel resonant converter with LLC-type commutation

It is shown that by using a proper transformation of state variables, the third-order system of the parallel resonant converter (PRC) with LLC-type commutation can be analyzed by means of a two-dimensional state-plane diagram. A set of characteristic curves which can be used for the converter design is derived from the analysis. It is shown from these curves that the converter possesses more desirable features than the conventional PRC     

LLC parallel resonant converter design by scaling the LC converter

An efficient and practical method for steady-state design of an LLC-type parallel resonant dc/dc converter (LLC-PRC) is presented. In general, the output characteristic curves of LLC-PRC can be obtained by multiplying the output curves of the LC-type parallel resonant converter (LC-PRC) by a ratio of the parallel and series inductances. The peak voltage and current stresses on the resonant elements also depend on the same ratio. The LLC-PRC with a filter inductor is examined for two conduction modes, continuous and discontinuous capacitor voltage conduction modes, to show the effect of the inductance ratio. A means to use the derived equations to obtain the zero current switching (ZCS) is given. Also, a design procedure, along with design examples, is given to illustrate the use of the equations and characteristic curves. An experimental LLC-PRC is built to ensure the validity of the equations and design examples     

Effect of FET output capacitance on ZVS of resonant converters

The analysis of resonant converters including the capacitance of the switches is presented. New dc characteristics are obtained for the series, parallel, and series-parallel resonant converters (SPRC). The operating regions where the converters operate with zero-voltage switching (ZVS) are determined as a function of the switch capacitance. The more pronounced effect can be seen in the series resonant converter (SRC), while the parallel resonant converter (PRC) is the most insensitive. The results of the analysis have been verified on an experimental prototype     

Analysis of series-parallel resonant converter

A frequency-domain steady-state analysis is given for a series-parallel resonant converter (SPRC) operating in the continuous conduction mode (CCM) using Fourier series techniques. Equations for performance parameters are derived under steady-state conditions to provide simple design tools. The topology of the SPRC combines the advantageous properties of both the series resonant converter (SRC) and the parallel resonant converter (PRC). The key results of the work are: a novel half-wave rectifier SPRC, conditions for obtaining high part-load efficiency; and several boundary frequencies and limiting conditions such as the capacitive/inductive load boundary and open-circuit and short-circuit cases. Experimental results measured for an 80-W converter above the resonance at different load resistances and input voltages show excellent agreement with the theoretical performance predicted by the equations     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Analysis of a PWM-resonant converter

When a parallel resonant tank is excited by a bipolar current pulse train a sinusoidal voltage develops across the tank whose amplitude depends on the duty cycle of the pulse train. An isolated secondary can be derived by applying the tank voltage to an isolation transformer whose magnetizing inductance acts as the resonant inductor of the tank circuit. A dc output voltage is obtained after rectification and filtering of the sinusoidal secondary voltage and regulation is achieved by controlling the duty cycle of the pulse train. The sinusoidal nature of the voltage across the isolation transformer alleviates some of the noise problem associated with parasitic capacitances of an isolation transformer when operated with square voltage waveform. In this work the dc and small-signal analysis of the converter is given and an equivalent small-signal circuit model is derived. Experimental results which confirm the validity of the model are presented.     

A design procedure for the phase-controlled parallel-loadedresonant inverter

High-frequency-link power conversion and distribution based on a resonant inverter has been recently proposed. The design of several topologies is reviewed and a simple approximate design procedure is developed for the phase-controlled parallel-loaded resonant inverter. This design procedure seeks to ensure the expected benefits of resonant conversion and is verified by data from a laboratory 2.5 kVA, 20-kHz converter. A simple phasor analysis is introduced as a useful approximation for design purposes. Experimental results show that under transient conditions such as load short-circuit, a reversal of the expected commutation sequence is possible. This should be accounted for in the design of the power circuit, or prevented by the design of the controller     

Analysis and design of (LC)(LC)-type series-parallel resonantconverter

A series-parallel resonant converter employing (LC)(LC)-type tank circuit operating in lagging power factor (PF) mode is presented and analyzed using complex ac circuit analysis. Design curves are obtained and the converter is optimized under certain constraints. Detailed Space Integrated Control Experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load conditions. Results obtained from an experimental converter are also presented. The results obtained from the theory, SPICE simulation, and the experimental converter are compared. The proposed converter has high efficiency from full load to very light load (<10%). Switching frequency variation required for a wide change in the load (near load open circuit to full load) is narrow compared with the series resonant converter (SRC)     

硅微谐振加速度计的研究现状及发展趋势

硅微谐振加速度计具有体积小、 功耗低、 准数字量输出和精度提升大的优点,是一种具有良好应用前景的高精度MEMS惯性仪表.总结分析了近些年国内外在硅微谐振加速度计方面的研究现状,主要在结构设计及工艺、 测控电路设计等方面阐述了各自特点.最后,结合近些年MEMS惯性仪表的发展趋势,对硅微谐振加速度计晶圆级真空封装、 测控电路数字化、仪表补偿智能化3个发展方向进行了展望.     

Multimodule parallel series-loaded resonant converters

The design and implementation of a multimodule parallel series-loaded resonant (SLR) converter system is presented. The SLR converter to be paralleled is operated in the n=2 discontinuous mode (DCM). Its dc analysis and dynamic modeling are made. In parallel operation, an average control technique is proposed to compensate the mismatch in current control characteristics of each parallel converter. Good dynamic and static current sharing characteristics are obtained. In addition, to obtain good output voltage regulating control performance, a design procedure is presented to find the parameters of feedback voltage controller according to the prescribed specifications     

Small signal analysis of the LCC-type parallel resonant converter

In this paper, the small signal analysis of the LCC-type parallel resonant converter (LCC-PRC) operating in the continuous conduction mode is given. This analysis is based on both the state-plane diagram, which has been successfully used to obtain the steady state response for resonant converters, and the Taylor series expansion. Applying perturbation directly to the steady state trajectory, a discrete small signal model for the converter can be derived in terns of the input voltage, switching frequency, and the converter state variables. Based on this analysis, closed-loop form solutions for the input-to-output and control-to-output transfer functions are derived. It is shown that the theoretical and computer simulation results are in full agreement     

A Normalized Model for the Half-Bridge Series Resonant Converter

Closed-form steady-state equations are derived for the halfbridge series resonant converter with a rectified (dc) load. Normalized curves for various currents and voltages are then plotted as a function of the circuit parameters. Experimental results based on a 10-kHz converter are presented for comparison with the calculations.     

Analysis and design of series-parallel resonant power supply

A modified series-parallel high-frequency resonant DC/DC converter configuration is proposed. A simplified steady-state analysis of the converter, including the effect of a high-frequency transformer using complex circuit analysis, is presented. Based on the analysis, a simple design procedure is given. The effect of magnetizing inductances of the high-frequency transformer on the performance of the converter is discussed. Detailed experimental results obtained from a MOSFET (metal-oxide-semiconductor field-effect-transistor)-based 1-kW converter are presented to verify the analysis. The converter presented has almost constant efficiency from full load to quarter load, and the converter has load short circuit capability     

并联H桥DC/DC变换器软开关技术研究

与传统的Buck电路相比,基于H桥并联的DC/DC变换器可以实现电压的双极性输出和故障时的冗余控制,非常适合用于大功率电动机正反转控制的场合。分析了并联H桥型DC/DC变换器的结构组成和双脉宽调制(PWM)模式。为了降低双脉宽调制下H桥型DC/DC变换器的开通和关断损耗,对无源软开关技术进行了分析,重点探讨了RCD缓冲电路和最小应力缓冲电路之间的性能差异,指出最小应力软开关技术可以获得更好的软开关性能,并就将其用于双脉宽调制下的并联H桥DC/DC变换器进行了仿真研究。仿真结果表明:最小应力软开关技术用于双脉宽调制下并联H桥DC/DC变换器时,可以实现开关管的零电压开通和零电流关断。     

State-plane analysis of zero-voltage-switching resonant DC/DCconverters

The state-plane analysis technique is established for the zero-voltage-switching resonant DC/DC power converter family of topologies, namely the buck, boost, buck-boost, Cuk, sepic, and dual-sepic converters. The state plane provides a compression of information, which allows the designer to examine the nonlinear dynamics of resonant converter operation. Utilizing the state plane, modes of resonant converter operation are examined. Expressions are derived for the switching frequencies at the boundaries between these modes and at the boundary of energy conversion     

Inherent Overload Protection for the Series Resonant Converter

The overload characteristics of the full bridge series resonant power converter are considered. This includes analyses of the two most common control methods presently in use. The first of these uses a current zero crossing detector to synchronize the control signals and is referred to as the ? controller. The second is driven by a voltage controlled oscillator and is referred to as the ? controller. It is shown that the ? controller has certain reliability advantages in that it can be designed with inherent short circuit protection. Experimental results are included for an 86 kHz converter using power metal-oxide-semiconductor field-effect transistors (MOSFETs).     

Generalized approach to the small signal modelling of DC-to-DCresonant converters

A generalized small-signal analysis approach that is based on both the Taylor's series expansion and the state-plane diagram is presented. A generalized discrete small-signal model for a double-ended DC-to-DC resonant converter operating in the continuous conduction mode is also given. Based on the model derived, the frequency responses for two transfer functions, namely, the line-to-output and the control-to-output transfer functions, are obtained. The technique is verified by applying it to the conventional series resonant converter whose small-signal analysis is known     

Robust controller design for a series resonant converter

Because of their reduced switching losses, allowing a higher operating frequency, dc-to-dc resonant converters have been used extensively in the design of smaller size and lighter weight power supplies. The steady state and dynamic behavior of both the conventional series and parallel resonant converters have been thoroughly analyzed and small-signal models around given nominal operating points have been obtained. These models have been used in the past to design controllers that attempted to keep the output voltage constant in the presence of input perturbations. However, these controllers did not take into account either load or components variations, and this could lead to instability in the face of component or load changes. Moreover, prediction of the frequency range for stability was done a posteriori, either experimentally or by a trial and error approach In this paper we use μ-synthesis to design a robust controller for a series resonant converter (SRC). In addition to robust stability the design objectives include rejection of disturbances at the converter input while keeping the control input and the settling time within values compatible with a practical implementation     

Resonant power supplies: their history and status

The various types of converter are described, and the history of resonant power supplies is briefly sketched. The differences between pulse-width-modulated (PWM) switch mode power supplies and resonant power supplies are discussed. Single-switch, multiple-switch, and series and parallel resonant converters are examined. The control of resonant converters is addressed. Hardware is briefly considered