表面深滚处理对纯镍组织性能及残余应力分布的影响

通过一种新型表面自纳米化方法———表面深滚处理,在纯镍（N4）表面制备出晶粒尺寸小于500nm 的梯度超细晶结构,并对材料次表面微观组织结构、残余应力分布及力学性能进行了研究。结果表明：N4经过表面深滚处理,表面形成织构;由于剧烈塑性变形,位错大量产生,并出现胞状组织和高密度位错墙,这些组织经过演化形成超细晶,并在表面形成具有一定厚度的残余压应力场;与原始材料相比,经过表面深滚处理后表面组织硬度提高近一倍;通过合理选择滚压参数,其细化层厚度、硬度、表面粗糙度及残余应力分布均得到不同程度改善。     

复杂异型零件小直径螺纹优质高效加工工艺研究与应用

复杂异型壳体类零件广泛应用于航空发动机控制附件,此类零件表面分布有大量小直径螺纹孔,螺纹孔加工是影响整个壳体生产加工效率和精度的核心工序。该类零件现有的加工工艺存在一致性差、加工效率低、专用夹具多、铣螺纹时易出现正锥现象等缺点。针对上述问题,提出并设计专用螺纹铣刀对小直径螺纹孔进行加工,通过宏程序编程解决刀具刃部缩短带来的编程问题,采用刃部长度为1～3个螺距的专用螺纹铣刀,同种刀具即可实现相同螺距不同规格的螺纹孔加工。通过对两个批次的零件进行实际加工验证,结果表明：工艺优化方案可使小直径螺纹孔加工质量及加工效率得到显著提升。     

Investigation on surface roughness,residual stress and fatigue property of milling in-situ TiB2/7050Al metal matrix composites

For higher efficiency and precision manufacturing, more and more attentions are focused on the surface roughness and residual stress of machined parts to obtain a good fatigue life. At present, the in-situ TiB₂/7050Al metal matrix composites are widely researched due to its attractive properties such as low density, good wear resistance and improved strength. It is of great significance to investigate the machined surface roughness, residual stress and fatigue life for higher efficiency and precision manufacturing of this new kind material. In this study, the surface roughness including two-dimensional and three-dimensional roughness, residual stress and fatigue life of milling in-situ TiB₂/7050Al metal matrix composites were analyzed. It was found from comparative investigation that the three-dimensional surface roughness would be more appropriate to represent the machined surface profile of milling particle reinforced metal matrix composites. The cutting temperature played a great role on the residual stress. However, the effect of increasing cutting force could slow down the transformation from compressive stress to tensile stress under 270 °C. An exponential relationship between three-dimensional roughness and fatigue life was established and the main fracture mechanism was brittle fracture with observation of obvious shellfish veins, river pattern veins and wave shaped veins in fracture surface.     

Investigation on surface integrity of electron beam melted Ti-6Al-4 V by precision grinding and electropolishing

Electron beam melting (EBM), as an excellent Additive Manufacturing (AM) technology, enables the printing of Ti-6Al-4 V alloy for a wide range of applications such as aerospace and biomechanical industries. It improves functionality and integrity of components and negates complexities in assembly processes. However, due to the poor surface and sub-surface integrity represented by the rough surface finish and low dimensional accuracy, achieving a favorable surface condition is quite challenging. Therefore, post processing becomes essential for these electron beam melted (EBM-ed) Ti-6Al-4 V alloys. Being the most common technique to improve such parts, milling of Ti-6Al-4 V alloy is very challenging and resulting tool wear issues, due to its unique material properties. Thus, this paper presents a comprehensive study on the surface integrity of EBM-ed Ti-6Al-4 V parts processed by precision grinding and electropolishing, aiming to qualitatively and quantitatively clarify the interrelation between process parameters and processed surface quality. The surface and subsurface characteristics such as profile accuracy, surface roughness, microstructure, defective layer and residual stress before and after post processing were compared and evaluated. The results show that by precision grinding, the profile accuracy was improved from over 300 µm PV to 7 µm PV, while surface roughness (R_a) was reduced from 30 µm to about 2 µm. The layer with partially melt particles was removed, but introduced a deformed subsurface layer with more residual stress. Then by applying electropolishing, the residual stress was released and the deformed layer was removed. In addition, R_a was further reduced to 0.65 µm. The research can serve as a reference for the integration of post machining processes with AM.     

浮动花键抗磨损强度分析与试验

为了解决航空发动机附件传动系统花键连接结构在正向设计阶段分析能力薄弱、缺少基础数据支撑,以及在复杂工作 条件下齿面磨损严重等问题,开展了浮动花键磨损强度评估方法研究,提出适用于发动机附件传动系统浮动花键的齿面接触应力 计算方法。并开展了花键磨损影响因素对比试验,测量不同材料、表面粗糙度、表面处理、润滑条件、偏斜角、齿形条件下的磨损量 和齿厚变化量。结果表明：花键表面硬度是决定抗磨损能力的主要因素,硬度大抗磨损能力强;在偏斜状态下工作的花键通过齿 形修形改善接触区位置,降低接触应力,可提高抗磨损能力;润滑油润滑可以减小摩擦磨损,减少磨屑产生,是减小花键磨损的首 要措施;正确选择齿侧间隙有利于减小磨损发生。     

磁流变弹性体砂轮抛光镍基高温合金表面完整性研究

为了改善磨削后镍基高温合金GH4169的表面完整性,本文采用磁流变弹性体砂轮对镍基高温合金GH4169进行抛光试验研究。首先,通过模压成型的方法制备了磁流变弹性体砂轮,并对其表面微观形貌及不同磁场强度下的硬度进行了表征。其次将制备出的磁流变弹性体砂轮用于对镍基高温合金GH4169的抛光工艺试验中,并讨论抛光工艺参数中磁场强度对镍基高温合金表面完整性的影响。试验结果表明：在一定的磁场强度范围内,零件抛光后的表面粗糙度和显微硬度随着磁场强度的增大而减小,同时增大磁场强度也有利于改善零件的表面形貌,减少砂轮的磨损量,降低零件磨削后的亚表面损伤层厚度。     

TB6钛合金抛光表面完整性试验

针对目前TB6钛合金类零件主要依靠手工抛光的技术问题,提出了羊毛毡轮数控抛光工艺,研究了抛光参数对表面粗糙度、表面硬度、表面残余应力的影响,进行了羊毛毡轮抛光参数优化,优选出了一组抛光参数:线速度v_s=19.63m/s,进给速度v_f=300mm/min,预压量a_p=0.5mm,加工行宽w=0.5mm。在此抛光参数下,羊毛毡轮抛光能够有效去除铣削刀纹,抛光后表面粗糙度R_a=0.15μm,并且抛光后表面残余应力为压应力。试验结果表明,该抛光方法能够有效地改善零件的表面完整性。     

光学材料磨削加工亚表面损伤层深度测量及预测方法研究

针对光学材料磨削加工引入的亚表面损伤层,综合使用磁流变抛光斑点技术和HF差动化学蚀刻速率法测量亚表面裂纹层深度和亚表面残余应力层厚度。建立了亚表面裂纹层深度与表面粗糙度间关系的理论模型,以实现亚表面裂纹层深度的准确预测,并通过分析亚表面裂纹尖端应力场,预测了亚表面裂纹尖端塑性层厚度。     

铝合金盘型件等温辗压过程中晶粒尺寸演化的数值模拟与实验验证

 为了揭示盘型件双面辗压成形过程中微观组织的演化特征,应用数值模拟方法研究了这一成形过程中所发生的动态再结晶和晶粒长大规律.所研究的盘型件材料为铝合金6061,辗压成形温度为350~500 ℃.晶粒尺寸演化规律的数值模拟结果与实验结果基本符合.与整体锻造不同,双面辗压成形没有变形死区,并且越靠近盘型件表面晶粒细化效果越好;辗压头通过对盘型件厚度方向压缩和表面环向剪切两种方式驱动盘型件变形.计算结果表明,即使压下量零增量辗压也会在沟槽附近产生显著变形和晶粒细化,这说明盘型件变形和组织演化主要源于辗压头对盘型件表面的环向剪切;多遍次辗压过程中,第1遍次辗压对晶粒细化的贡献最大,后续辗压的贡献较小;提高成形温度可能会出现动态晶粒长大区,在这种情况下,盘型件上的点将交替发生动态再结晶和动态晶粒长大,最终晶粒尺寸会有一定程度增加.     

Effects of in-situ TiB2 particles on machinability and surface integrity in milling of TiB2/2024 and TiB2/7075 Al composites

In-situ ceramics particle reinforced aluminum matrix composites are favored in the aerospace industry due to excellent properties. However, the hard ceramic particles as the reinforcement phase bring challenges to machining. To study the effect of in-situ TiB₂ particles on machinability and surface integrity of TiB₂/2024 composite and TiB₂/7075 composite, milling experiments were performed, and compared with conventional 2024 and 7075 aluminum alloys. In-situ TiB₂ particles clustered at the grain boundaries and dispersed inside the matrix alloy grains hinder the dislocation movement of the matrix alloy. Therefore, the milling force and temperature of the composites are higher than those of the aluminum alloys due to the increase of the strength and the decrease of the plasticity. In the milling of composites, abrasive wear is the main wear form of carbide tools, due to the scratching of hard nano-TiB₂ particles. The composites containing in-situ TiB₂ particles have machining defects such as smearing, micro-scratches, micro-pits and tail on the machined surface. However, in-situ TiB₂ particles impede the plastic deformation of the composites, which greatly reduces cutting edge marks on the machined surface. Therefore, under the same milling parameters, the surface roughness of TiB₂/2024 composite and TiB₂/7075 composite is much less than that of 2024 and 7075 aluminum alloy respectively. Under the milling conditions of this experiment, the machined subsurface has no metamorphic layer, and the microhardness of the machined surface is almost the same as that of the material. Besides, compared with 2024 and 7075 aluminum alloy, machined surfaces of TiB₂/2024 composite and TiB₂/7075 composite both show tensile residual stress or low magnitude of compressive residual stress.     

Dimension Accuracy and Surface Integrity of Creep Feed Ground Titanium Alloy with Monolayer Brazed CBN Shaped Wheels

Titanium alloy tenon is creep feed ground with monolayer brazed cubic boron nitride (CBN) shaped wheels. The dimension accuracy of the tenon is assessed and the results indicate that it completely meets the requirement of blade tenon of aero-engine. Residual stresses, surface roughness, microstructure and microhardness are measured on ground surfaces of the specimen, which are all compared with that ground with vitrified CBN wheels. Under all the circumstances, compressive residual stress is obtained and the depth of the machining affected zone is found to be less than 40 μm. No phase transformation is observed at depths of up to 100 μm below the surface, though plastic deformation is visible in the process of grain refinement. The residual stress and microhardness of specimens ground with brazed CBN wheels are observed to be lower than those ground with vitrified ones. The arithmetic mean roughness (R_a) values obtained are all below 0.8 μm.     

钛合金切削挤压复合攻丝研究

将切削挤压复合攻丝新方法成功地用于高强度钛合金内螺纹的加工,这种方法不仅可以减小挤压扭矩而且能够强化螺纹根部。加工的挤压螺纹表面有一层纤维沿其牙形连续分布。利用云纹干涉法测得牙根处的最大残余压应力为120MPa左右。疲劳对比试验结果表明,在相同应力水平下,经挤压强化螺纹的疲劳寿命大约是未强化螺纹的３倍,这主要归因于挤压螺纹表面高的残余压应力,高的纤维密度和低的粗糙度。     

Ironing effect on surface integrity and fatigue behavior during ultrasonic peening drilling of Ti-6Al-4V

Imposing compressive residual stress field around a fastening hole serves as a universal method to enhance the hole fatigue strength in the aircraft assembly filed. Ultrasonic Peening Drilling (UPD) is a recently proposed hybrid hole making process, which can achieve an integration of strengthening and precision-machining with a one-shot-drilling operation. Due to the ironing effect of tool flank surface, UPD introduces large compressive residual stress filed in hole subsurface. In order to reveal the strengthening mechanism of UPD, the influence of ultrasonic vibration and tool dynamic relief angle on ironing coverage rate and its corresponding effect on surface integrity in UPD were analyzed. The experiments were conducted to verify the influence of ironing effect on surface integrity and fatigue behavior of Ti-6Al-4V hole in UPD. The results indicate that the specimen features smaller surface roughness, higher micro-hardness, plastic deformation degree and circumferential compress residual stress under higher ironing coverage rate. The fatigue life increases with the raise of ironing coverage rate, and the fatigue source site in UPD shifts from surface to subsurface comparing with that without vibration assistance. The results demonstrates that a better strengthening effect can be obtained by reasonably controlling the ironing coverage rate in UPD.     

Experimental investigation of laser peening on TiAl alloy microstructure and properties

In order to study the effect of laser peening on microstructures and properties of Ti Al alloy, Ti Al alloy samples were treated by Nd:YAG laser system with the wavelength of 1064 nm,pulse-width of 18 ns, and pulse-energy of 0–10 J. Surface micro-hardness, roughness, and microstructural characteristics were tested with micro-hardness tester, roughness tester and scanning electron microscope. Residual stress and pole figures were tested with X-ray diffraction and its high-temperature stability was analyzed. The experimental results show that surface micro-hardness increases by up to 30%, roughness increases to 0.37 lm, compressive residual stress increases to 337 MPa, and local texture and typical lamellar microstructure are generated. Residual stress, micro-hardness, and(002) pole figures tests are conducted, compressive residual stress value drops from 337 MPa to 260 MPa, hardness value drops from 377 HV_(0.2) to 343 HV_(0.2), and the(002)poles shift back to the center slightly. Laser peening improves microstructure and properties of Ti Al alloy significantly.     

激光选区熔化成型316L不锈钢工艺参数研究

针对激光选区熔化成型316L不锈钢工艺参数选择问题,采用单因素条件变量分析法,在激光选区熔化过程中,分析了激光功率、扫描速度对316L不锈钢成型零件表面粗糙度、致密度、硬度和尺寸偏差的影响规律。结果表明：当激光功率降低或者扫描速度提高时,内部能量密度减小,粉末熔化量减少,试样表面球化效应增强,孔隙缺陷增多,试样致密度减小、硬度降低;当激光功率提高或者扫描速度降低时,内部能量密度增大,粉末被过度烧蚀,产生较大的尺寸偏差,所形成熔道易塌陷,导致层间结合较差,试样性能降低。当激光功率为300 W、扫描速度为1000 mm/s时,能量密度适中,形成了较好的冶金结合,抗拉强度可达753 MPa,上表面硬度HRB能达到97.22。该项研究为316L不锈钢激光选区熔化工艺参数的合理选择提供了参考。     

Grinding force and surface quality in creep feed profile grinding of turbine blade root of nickel-based superalloy with microcrystalline alumina abrasive wheels

Creep feed profile grinding of the fir-tree blade root forms of single crystal nickel-based superalloy was conducted using microcrystalline alumina abrasive wheels in the present study. The grinding force and the surface quality in terms of surface topography, subsurface microstructure, microhardness and residual stress obtained under different grinding conditions were evaluated comparatively. Experimental results indicated that the grinding force was influenced significantly by the competing predominance between the grinding parameters and the cross-sectional root workpiece profile. In addition, the root workpiece surface, including the root peak and valley regions, was produced with the large difference in surface quality due to the nonuniform grinding loads along the root workpiece profile in normal section. Detailed results showed that the surface roughness, subsurface plastic deformation and work hardening level of the root valley region were higher by up to 25%, 20% and 7% in average than those obtained in the root peak region, respectively, in the current investigation. Finally, the superior parameters were recommended in the creep feed profile grinding of the fir-tree blade root forms. This study is helpful to provide industry guidance to optimize the machining process for the high-valued parts with complicated profiles.     

弧线齿面齿轮应力过程分析

为了给弧线齿面齿轮的齿面接触强度和齿根弯曲强度设计提供理论依据,研究了弧线齿面齿轮的齿面接触应力和齿根弯曲应力随载荷和安装误差的变化规律.在齿面接触分析和承载接触分析的基础上应用弹性理论计算了弧线齿面齿轮副的齿面接触应力和应用有限元应力影响矩阵法计算了该齿轮副的齿根弯曲应力.给出了数字计算实例,计算结果表明:齿面接触强度和齿根弯曲强度在重载时的接触强度和弯曲强度由单齿啮合区的强度决定,轴向安装误差和轴夹角安装误差分别会增加齿面接触应力和齿根弯曲应力,轴夹角安装误差和轴间距安装误差对齿面接触应力影响甚小,而轴向安装误差和轴间距安装误差可以降低齿根弯曲应力,与直齿面齿轮相比,弧线齿面齿轮的接触和弯曲应力明显减小.      

A356-T6/6061-T6异种铝合金搅拌摩擦焊的工艺研究

通过对6 mm厚的A356-T6/6061-T6异种铝合金的搅拌摩擦焊工艺试验研究,采用OM、SEM、万能拉伸试验机、显微硬度仪等分析了母材位置、焊接速度对接头组织和性能的影响。研究结果表明:当旋转速度为1 000 r/min、焊接速度为100~400 mm/min时,均可获得内部无明显缺陷、外观良好的异种铝合金接头;A356-T6铝合金置于前进侧时有利于材料的迁移,焊缝区组织由典型的焊核区、热机械影响区和热影响区特征组织组成,焊核区域晶粒由表层向底层逐渐细化;接头拉伸性能随焊接速度的增加而增大;焊接速度较低时,A356合金位于前进侧有利于获得强度更高的接头,而焊接速度较高时,6061位于前进侧有利于获得高性能接头,且接头的屈服强度和延伸率均较A356位于前进侧时高;无论A356还是6061置于前进侧,接头的断裂位置均位于A356侧热影响区,与母材放置位置无关,这与焊缝硬度最小值区位置相吻合。     

A novel unified model predicting flow stress and grain size evolutions during hot working of non-uniform as-cast 42CrMo billets

The cast preformed forming process(CPFP) is increasingly considered and applied in the metal forming industries due to its short process, low cost, and environmental friendliness, especially in the aerospace field. However, how to establish a unified model of a non-uniform as-cast billet depicting the flow stress and microstructure evolution behaviors during hot working is the key to microstructure prediction and parameter optimization of the CPFP. In this work, hot compression tests are performed using a non-uniform as-cast 42 CrMo billet at 1123–1423 K and 0.01–1sà1. The effect laws of the non-uniform state of the as-cast billet with different initial grain sizes on the flow stress and microstructure are revealed deeply. Based on experimental results, a unified model of flow stress and grain size evolutions is developed by the internal variable modeling method. Verified results show that the model can well describe the responses of the flow stress and microstructure to deformation conditions and initial grain sizes. To further evaluate its reliability, the unified model is applied to FE simulation of the cast preformed ring rolling process.The predictions of the rolling force and grain size indicate that it could well describe the flow stress and microstructure evolutions during the process.     

激光增材制造钛合金构件的化学抛光工艺研究

采用HNO3-HF抛光液对激光选区熔化钛合金制件进行化学抛光,以试样表面粗糙度、减薄及失重变化为指标探究了抛光过程中不同温度和时间对钛合金增材制件抛光效果的影响。通过电化学测量、拉伸试验、残余应力测试等方法对比分析了化学抛光前后钛合金试样的电化学和力学性能。结果表明在温度30℃、反应时间10min下抛光钛合金可以取得较理想的抛光效果,试样表面粗糙度减小、耐腐蚀性能提高。化学抛光后钛合金的强度出现小幅下降,内部原有的残余应力由拉应力转变为压应力。