THE CLUSTER DATA PROCESSING SYSTEM: A DISTRIBUTED SYSTEM IN SUPPORT OF A CHALLENGING SCIENTIFIC MISSION

The Cluster mission is aimed at the study of small-scale structures that are believed to be fundamental in determining the behaviour of key interactive processes of cosmic plasma. The mission will be controlled from the European Space Operations Centre (ESOC). ESOC is also in charge of the commanding of the scientific payloads on-board the four Cluster spacecraft after negotiation with the Cluster Principal Investigators (PIs) and of collecting and distributing the mission's scientific results to the Cluster community. This paper describes the process of translating the scientific requirements of the Cluster mission into a data-processing system supporting the mission via the definition of an appropriate operational scenario. In particular, the process of negotiation between the PIs and ESOC to command the spacecraft is mediated by the Joint Science Operations Centre (JSOC) and finalised by the Cluster Mission Planning System (CMPS) while the return of the data to the Cluster community is actuated by the Cluster Data Disposition System (CDDS). The Cluster Mission Control System (CMCS) provides the interface between these two systems and the spacecraft. These elements constitute the Cluster Data-Processing System (CDPS).     

THE CLUSTER SCIENCE DATA SYSTEM (CSDS) – A NEW APPROACH TO THE DISTRIBUTION OF SCIENTIFIC DATA

Cluster is an ESA/NASA four-spacecraft mission designed to study plasma processes in three dimensions using the combined data from eleven instruments on each spacecraft. This mission requires the combination of many measured parameters, and the Cluster community have taken the unprecedented step of establishing a set of high quality data products from all instruments at spin (~ 4 s) resolution which will be produced and distributed throughout the mission lifetime. The Cluster Science Data System (CSDS) is based on a set of eight data centres which are implemented and funded through national programmes. As part of CSDS, a Joint Science Operations Centre (JSOC) has been established to facilitate the commanding of the 44 instruments. It is co-located with the UK data centre at the Rutherford Appleton Laboratory (RAL), Didcot, United Kingdom. ESA's contribution to CSDS includes the provision of the CSDS User Interface, a dedicated network (CSDSnet) to interconnect the data centres, and the co-ordination of all activities at CSDS level. A wide scientific community wishing to use Cluster data will have differing data rights, experience and means of access. Users will also include those working with data sets from other missions, e.g., Soho, Geotail, Wind, Polar, Interball, and Equator-S. The Cluster Science Data System is primarily designed to support multi-instrument and multi-spacecraft data analysis and it is distributed across six national data centres in Europe, one in the USA, and one in China. CSDSnet will be used to interconnect the European data centres, the Joint Science Operations Centre at Didcot and the spacecraft Operations Control Centre at ESOC in Darmstadt.     

CLUSTER MISSION OPERATIONS

The Cluster ground segment design and mission operations concept have been defined according to the basic mission requirements, namely, to allow the transfer of the four spacecraft from the initial geostationary transfer orbit achieved at separation from the launcher into the final highly elliptical polar orbits, such that in the areas of scientific interest along their orbits, the four spacecraft will form a tetrahedral configuration with pre-defined separation distances, to be changed every six months during the mission. The Cluster mission operations will be carried out by ESA from its European Space Operations Centre; the task of merging the Principal Investigators' requests into coordinated, regular scientific mission planning inputs to ESOC will be undertaken by the Joint Science Operations Centre. The mission products will be distributed to the scientific community regularly in form of CD-ROMs. Principal Investigators will also have access to quick-look science, housekeeping telemetry and auxiliary data via an electronic network.     

Scientific Planning and Commanding of the Rosetta Payload

ESA’s Rosetta mission was launched in March 2004 and is on its way to comet 67P/Churyumov-Gerasimenko, where it is scheduled to arrive in summer 2014. It comprises a payload of 12 scientific instruments and a Lander. All instruments are provided by Principal Investigators, which are responsible for their operations. As for most ESA science missions, the ground segment of the mission consists of a Mission Operations Centre (MOC) and a Science Operations Centre (SOC). While the MOC is responsible for all spacecraft-related aspects and the final uplink of all command timelines to the spacecraft, the scientific operations of the instruments and the collection of the data and ingestion into the Planetary Science Archive are coordinated by the SOC. This paper focuses on the tasks of the SOC and in particular on the methodology and constraints to convert the scientific goals of the Rosetta mission to operational timelines.     

The Interstellar Boundary Explorer Science Operations Center

The Interstellar Boundary Explorer (IBEX) Science Operations Center is responsible for supporting analysis of IBEX data, generating special payload command procedures, delivering the IBEX data products, and building the global heliospheric maps of energetic neutral atoms (ENAs) in collaboration with the IBEX team. We describe here the data products and flow, the sensor responses to ENA fluxes, the heliospheric transmission of ENAs (from 100 AU to 1 AU), and the process of building global maps of the heliosphere. The vast majority of IBEX Science Operations Center (ISOC) tools are complete, and the ISOC is in a remarkable state of readiness due to extensive reviews, tests, rehearsals, long hours, and support from the payload teams. The software has been designed specifically to support considerable flexibility in the process of building global flux maps. Therefore, as we discover the fundamental properties of the interstellar interaction, the ISOC will iteratively improve its pipeline software, and, subsequently, the heliospheric flux maps that will provide a keystone for our global understanding of the solar wind’s interaction with the interstellar medium. The ISOC looks forward to the next chapter of the IBEX mission, as the tools we have developed will be used in partnership with the IBEX team and the scientific community over the coming years to define our global understanding of the solar wind’s interaction with the local interstellar medium.     

The IMAGE science and mission operations center

The Imager for Magnetopause-to-Aurora Global Exploration (IMAGE) will produce forefront science by quantifying the response of the magnetosphere to the time variable solar wind. It will acquire, for the first time, a variety of three-dimensional images of magnetospheric boundaries and plasma distributions extending from the magnetopause to the inner plasmasphere. The images will be produced on time scales needed to answer important questions about the interactions of the solar wind and the magnetosphere. The IMAGE team will provide open access to all IMAGE data. Thus there will be no proprietary rights or periods. All IMAGE data products will be archived and available to the scientific research community. The IMAGE mission will operate with a near 100% duty cycle with all instruments in their baseline operational modes. A Science and Mission Operations Control Center or SMOC has been developed at the NASA Goddard Space Flight Center (GSFC) to be the main data and command processing system for IMAGE. The IMAGE Level-0 data will be processed into Level 0.5 and Level-1 data and browse products within 24 hours after their receipt of raw data in the SMOC. These data products will be transferred to the NSSDC, for long-term archiving, and posted immediately on the world-wide-web for use by the international scientific community and the public.     

The German satellite mission TerraSAR-X

TerraSAR-X is Germany's first national remote sensing satellite being implemented in a public-private partnership between the German Aerospace Centre (DLR) and EATS Astrium GmbH. TerraSAR-X was launched on June 15, 2007 and will supply high-quality radar data for purposes of scientific observation of the Earth for a period of at least five years. At the same time, it is designed to satisfy the steadily growing demand of the private sector for remote sensing data in the commercial market [1].     

ISTP science data systems and products

The International Solar-Terrestrial Physics (ISTP) program will provide simultaneous coordinated scientific measurements from most of the major areas of geospace including specific locations on the Earth's surface. This paper describes the comprehensive ISTP ground science data handling system which has been developed to promote optimal mission planning and efficient data processing, analysis and distribution. The essential components of this ground system are the ISTP Central Data Handling Facility (CDHF), the Information Processing Division's Data Distribution Facility (DDF), the ISTP/Global Geospace Science (GGS) Science Planning and Operations Facility (SPOF) and the NASA Data Archive and Distribution Service (NDADS).The ISTP CDHF is the one place in the program where measurements from this wide variety of geospace and ground-based instrumentation and theoretical studies are brought together. Subsequently, these data will be distributed, along with ancillary data, in a unified fashion to the ISTP Principal Investigator (PI) and Co-Investigator (CoI) teams for analysis on their local systems. The CDHF ingests the telemetry streams, orbit, attitude, and command history from the GEOTAIL, WIND, POLAR, SOHO, and IMP-8 Spacecraft; computes summary data sets, called Key Parameters (KPs), for each scientific instrument; ingests pre-computed KPs from other spacecraft and ground basel investigations; provides a computational platform for parameterized modeling; and provides a number of data services for the ISTP community of investigators. The DDF organizes the KPs, decommutated telemetry, and associated ancillary data into products for duistribution to the ISTP community on CD-ROMs. The SPOF is the component of the GGS program responsible for the development and coordination of ISTP science planning operations. The SPOF operates under the direction of the ISTP Project Scientist and is responsible for the development and coordination of the science plan for ISTP spacecraft. Instrument command requests for the WIND and POLAR investigations are submitted by the PIs to the SPOF where they are checked for science conflicts, forwarded to the GSFC Command Management Syntem/Payload Operations Control Center (CMS/POCC) for engineering conflict validation, and finally incorporated into the conflict-free science operations plan. Conflict resolution is accomplished through iteration between the PIs, SPOF and CMS and in consultation with the Project Scientist when necessary. The long term archival of ISTP KP and level-zero data will be undertaken by NASA's National Space Science Data Center using the NASA Data Archive and Distribution Service (NDADS). This on-line archive facility will provide rapid access to archived KPs and event data and includes security features to restrict access to the data during the time they are proprietary.     

The MESSENGER Science Operations Center

The MESSENGER Science Operations Center (SOC) is an integrated set of subsystems and personnel whose purpose is to obtain, provide, and preserve the scientific measurements and analysis that fulfill the objectives of the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) mission. The SOC has two main functional areas. The first is to facilitate science instrument planning and operational activities, including related spacecraft guidance and control operations, and to work closely with the Mission Operations Center to implement those plans. The second functional area, data management and analysis, involves the receipt of science-related telemetry, reformatting and cataloging this telemetry and related ancillary information, retaining the science data for use by the MESSENGER Science Team, and preparing data archives for delivery to the Planetary Data System; and the provision of operational assistance to the instrument and science teams in executing their algorithms and generating higher-level data products.     

Customers and actors of ATM: military users

The airspace users community encompasses a wide range of quite different interest groups involved either in Commercial Air Transport Operations, Military Operations, General Aviation & Aerial Work Operations or Test Flights & Unmanned Aerial Vehicles Operations. Military Aviation plays a special role among these airspace users because of its specific needs related to the type of ATM services requested and the priority of access to airspace.     

Rosetta Ground Segment and Mission Operations

At the European Space Operations Centre in Darmstadt (Germany) the activities for ground segment development and mission operations preparation for Rosetta started in 1997. Many of the characteristics of this mission were new to ESOC and have therefore required an early effort in identifying all the necessary facilities and functions. The ground segment required entirely new elements to be developed, such as the large deep-space antenna built in New Norcia (Western Australia). The long duration of the journey to the comet, of about 10 years, required an effort in the operations concept definition to reduce the cost of routine monitoring and control. The new approaches adopted for the Rosetta mission include full transfer of on-board software maintenance responsibility to the operations team, and the installation of a fully functioning spacecraft engineering model at ESOC, in support of testing and troubleshooting activities in flight, but also for training of the operations staff. Special measures have also been taken to minimise the ground contact with the spacecraft during cruise, to reduce cost, down to a typical frequency of one contact per week. The problem of maintaining knowledge and expertise in the long flight to comet Churyumov–Gerasimenko is also a major challenge for the Rosetta operations team, which has been tackled early in the mission preparation phase and evolved with the first years of flight experience.     

国内外深空探测器精密定轨软件研究综述及WUDOGS简介

深空探测器精密定轨软件系统的研制在深空探测活动中是一个非常重要的环节,一直受到各大航天机构的重视。针对国内外深空探测器精密定轨软件平台的研究现状,重点介绍了具有代表性的美国JPL(Jet Propulsion Laboratory,喷气推进实验室)的DPTRAJ/ODP(Double Precision TRAJectory program/Orbit Determination Program,双精度轨道程序/定轨程序)和MONTE(Mission analysis,Operations,and Navigation Toolkit Environment,任务分析、操作和导航工具箱环境),GSFC(Goddard Space Flight Center,戈达德航天飞行中心)的GEODYN-II以及法国CNES(Centre National dEtudes Spatiales,国家空间研究中心)的GINS(Géodésie par Intégrations Numériques Simultanées,同步数值积分大地测量)软件系统,对这些软件的结构与功能进行了总结。之后对武汉大学自主研制的深空探测器精密定轨软件系统WUDOGS(Wuhan University Deep space Orbit determination and Gravity recovery System,武汉大学深空探测器精密定轨与重力场解算软件系统)的主要模块与功能进行了介绍,通过与GEODYN-II的交叉对比验证,表明:对于探测器的轨道预报,WUDOGS与GEODYN-II的1个月位置差异小于0.3mm,2d位置差值小于5×10~(-3) mm;双程测距、双程测速的理论计算值和GEODYN-II的差值RMS(Root Mean Square,均方根)分别在0.06mm,0.002mm/s的水平;WUDOGS目前已初步具备了月球和火星探测器精密定轨能力。最后对WUDOGS的下一步发展方向进行了展望。     

Designing a power plant with highest efficiency:results from SFB 561

The goal of Collaborative Research Centre(SFB) 561 "thermally highly loaded,porous and cooled multi-layer systems for combined cycle power plants" is to expand the current technological and scientific knowledge on power plants in order to achieve total efficiencies of 65% in a combined cycle power plant in the year 2025.Therefore,the aero-thermomechanical,structural-mechanical,materials' scientific and production fundamentals for the development of steam and gas turbine components that are able to withstand highest thermal loads are being worked out within this SFB.This means for the gas turbine that combustion chamber outlet temperatures of 1520℃ at 1.7MPa are to be attained.In order to control these high temperatures,it is not only required to develop new materials' solutions,including thermal barrier coatings,but also to apply improved cooling techniques,as for example effusion cooling.This novel cooling concept is to be realised through open-porous structures.These structures can consist of drilled open-porous multi-layer systems or open-porous metallic foams.The development of graded multi-layer systems is also extremely important,as the grading will enable the use of coolant in dependence of the requirements.The live steam parameters in the high pressure turbine are expected to be increased up to approximately 700℃ with pressure of 30MPa.These elevated steam parameters can be encountered with Ni-base alloys,but this is a costly alternative,associated with many manufacturing difficulties.Therefore,the SFB proposes cooling the highly loaded turbines instead,as this would necessitate the application of far less Ni-base alloys.To protect the thermally highly loaded casing,a sandwich material consisting of two thin face sheets with a core of a woven wire mesh is used to cover the walls of the steam turbine casing.The current state of the research shows that by utilising innovative cooling technologies a total efficiency of 65% can be reached without exceeding the maximum allowable material temperature,thereby prolonging the life-span.      

SOHO operations and ground system

SOHO is a joint ESA/NASA mission to study the sun from its interior to, and including, the solar wind in interplanetary space. It is currently scheduled for launch in 1995. After launch SOHO with be operated from the Experiment Operations Facility (EOF) at Goddard Space Flight Center (GSFC). The EOF will consist of facilities for instrument commanding, data reception, data reduction and data analysis. In this paper the operations concepts including instrument ground commanding from the EOF and communications capabilities between the EOF and ground observatories and the public networks in general will be described.     

Aerial Mapping Planetary Bodies

Photographic mapping missions over planetary bodies present a number of interesting hardware, operational, data retrieval, and data analysis techniques. Broadly speaking, such a mapping mission can be conducted with present level state-of-the-art equipment. The space-craft and photographic equipment must perform over long periods of time unattended in the hostile space environment. Operations must support the mission and retrieve the photographic data. Maximum data are limited by photographic capacity, operations capacity, and analysis capacity. Data analysis techniques are under development and computer maps have been developed for RANGER analysis; these techniques can be especially suited to analysis of the video (analog or digital) signal transmitted back to Earth.     

Urey: Mars Organic and Oxidant Detector

One of the fundamental challenges facing the scientific community as we enter this new century of Mars research is to understand, in a rigorous manner, the biotic potential both past and present of this outermost terrestrial-like planet in our solar system. Urey: Mars Organic and Oxidant Detector has been selected for the Pasteur payload of the European Space Agency’s (ESA’s) ExoMars rover mission and is considered a fundamental instrument to achieve the mission’s scientific objectives. The instrument is named Urey in recognition of Harold Clayton Urey’s seminal contributions to cosmochemistry, geochemistry, and the study of the origin of life. The overall goal of Urey is to search for organic compounds directly in the regolith of Mars and to assess their origin. Urey will perform a groundbreaking investigation of the Martian environment that will involve searching for organic compounds indicative of life and prebiotic chemistry at a sensitivity many orders of magnitude greater than Viking or other in situ organic detection systems. Urey will perform the first in situ search for key classes of organic molecules using state-of-the-art analytical methods that provide part-per-trillion sensitivity. It will ascertain whether any of these molecules are abiotic or biotic in origin and will evaluate the survival potential of organic compounds in the environment using state-of-the-art chemoresistor oxidant sensors.     

InSight Mars Lander Robotics Instrument Deployment System

The InSight Mars Lander is equipped with an Instrument Deployment System (IDS) and science payload with accompanying auxiliary peripherals mounted on the Lander. The InSight science payload includes a seismometer (SEIS) and Wind and Thermal Shield (WTS), heat flow probe (Heat Flow and Physical Properties Package, HP³) and a precision tracking system (RISE) to measure the size and state of the core, mantle and crust of Mars. The InSight flight system is a close copy of the Mars Phoenix Lander and comprises a Lander, cruise stage, heatshield and backshell. The IDS comprises an Instrument Deployment Arm (IDA), scoop, five finger “claw” grapple, motor controller, arm-mounted Instrument Deployment Camera (IDC), lander-mounted Instrument Context Camera (ICC), and control software. IDS is responsible for the first precision robotic instrument placement and release of SEIS and HP³ on a planetary surface that will enable scientists to perform the first comprehensive surface-based geophysical investigation of Mars’ interior structure. This paper describes the design and operations of the Instrument Deployment Systems (IDS), a critical subsystem of the InSight Mars Lander necessary to achieve the primary scientific goals of the mission including robotic arm geology and physical properties (soil mechanics) investigations at the Landing site. In addition, we present test results of flight IDS Verification and Validation activities including thermal characterization and InSight 2017 Assembly, Test, and Launch Operations (ATLO), Deployment Scenario Test at Lockheed Martin, Denver, where all the flight payloads were successfully deployed with a balloon gravity offload fixture to compensate for Mars to Earth gravity.     

STEREO Ground Segment, Science Operations, and Data Archive

Vitally important to the success of any mission is the ground support system used for commanding the spacecraft, receiving the telemetry, and processing the results. We describe the ground system used for the STEREO mission, consisting of the Mission Operations Center, the individual Payload Operations Centers for each instrument, and the STEREO Science Center, together with mission support from the Flight Dynamics Facility, Deep Space Mission System, and the Space Environment Center. The mission planning process is described, as is the data flow from spacecraft telemetry to processed science data to long-term archive. We describe the online resources that researchers will be able to use to access STEREO planning resources, science data, and analysis software. The STEREO Joint Observations Program system is described, with instructions on how observers can participate. Finally, we describe the near-real-time processing of the “space weather beacon” telemetry, which is a low telemetry rate quicklook product available close to 24 hours a day, with the intended use of space weather forecasting.     

Data link communication equipment approved by USAF for civil air traffic control

Operations within civil airspace will transition from traditional ground-based air traffic control (ATC) to air traffic management (ATM), a concept that requires aircrews and ground managers to share responsibility of aircraft separation assurance. Increased levels of information exchange will be necessary for this concept to work safely; therefore, air-ground communications will transition from voice to data link communications. The nature of data link communications procurement requires that avionics suppliers not only verify their products meet contractual performance requirements, but also demonstrate that their products are compatible with civil communication networks and ATC. In addition, the USAF needs to demonstrate that their crew-training program is adequate to maintain the required level of aircrew proficiency and equipment can be maintained for the required level of system performance, integrity, and interoperability with the civil environment. This paper outlines some of the certification issues facing the USAF with respect to the "Approval for Use" of data link equipment to be used for communication with ATC. It will also suggest a methodology for the avionics supplier and USAF to obtain the approvals required to ensure the installation of data link communications equipment on military aircraft will remain interoperable with civil ATC.     

The Lunar Reconnaissance Orbiter Laser Ranging Investigation

The objective of the Lunar Reconnaissance Orbiter (LRO) Laser Ranging (LR) system is to collect precise measurements of range that allow the spacecraft to achieve its requirement for precision orbit determination. The LR will make one-way range measurements via laser pulse time-of-flight from Earth to LRO, and will determine the position of the spacecraft at a sub-meter level with respect to ground stations on Earth and the center of mass of the Moon. Ranging will occur whenever LRO is visible in the line of sight from participating Earth ground tracking stations. The LR consists of two primary components, a flight system and ground system. The flight system consists of a small receiver telescope mounted on the LRO high-gain antenna that captures the uplinked laser signal, and a fiber optic cable that routes the signal to the Lunar Orbiter Laser Altimeter (LOLA) instrument on LRO. The LOLA instrument receiver records the time of the laser signal based on an ultrastable crystal oscillator, and provides the information to the onboard LRO data system for storage and/or transmittal to the ground through the spacecraft radio frequency link. The LR ground system consists of a network of satellite laser ranging stations, a data reception and distribution facility, and the LOLA Science Operations Center. LR measurements will enable the determination of a three-dimensional geodetic grid for the Moon based on the precise seleno-location of ground spots from LOLA.