基于多目标的飞行参数规划模型研究

分析了以飞机的飞行高度和速度为参数,以飞行总时间和燃油消耗为目标的飞行参数规划模型,并解算出此规划模型的最优解和目标函数的最优值。仿真分析结果表明目标函数选取不同,会对模型的最优解和最优值产生影响。此模型可为飞行参数规划研究提供参考。     

基于灵敏度分析的飞行器稳健设计优化方法

提出了一种基于灵敏度分析的稳健设计优化方法。针对设计变量存在扰动的不确定性问题,在原有优化数学模型上,增加了准则函数和约束函数的灵敏度附加项。采用全局灵敏度方程来计算准则函数及约束函数对设计变量的灵敏度,进而得出新的优化问题数学模型,得到问题的稳健性解。将上述方法应用到轻型飞机的总体设计中,对飞机重量、气动和性能模块进行多目标优化,得出最优解,并与已有的飞机进行对比和分析。     

考虑重心位置不确定性的无尾无人机优化设计

飞机的飞行性能与重心(CG)位置密切相关,尤其是后掠式无尾飞机的重心位置对其飞行性能影响更甚,如果重心位置发生变化,升力分布随之改变,进而影响飞机航时。针对这个问题,从气动布局和设计方法两方面,设计了一种航时对重心位置不敏感的无尾无人机(UAV)。气动布局上,提出了利用螺旋桨动力配平纵向力矩的鸥翼(GW)布局,以减小重心位置变化对升阻特性的影响;设计方法上,采用稳健性优化设计(RDO)理论,分析重心位置不确定时的航时低敏感度问题。以一架小型电动无人机为研究对象,建立了无尾无人机稳健性优化设计环境,包括总体设计、代理模型构造以及稳健性优化。分析结果表明:利用螺旋桨动力配平的鸥翼布局使重心可用范围增加了5%;静安定裕度在5%~15%变化时,该布局可以有效提高航时稳健性。采用稳健性优化得到的无人机几何参数,大幅度降低了重心位置对航时的影响,显著提升了满足约束的概率。     

民用飞机重心包线研究

民用飞机重心包线是保证飞机使用安全的重要防线,是飞机飞行使用中不可逾越的一道屏障。重心包线设计的好坏不仅影响飞机的飞行性能,更直接影响飞机使用的经济性和安全性,其确定是总体、气动、操稳、性能、强度、重量等多专业分析、权衡的结果。从重心对性能的影响,重心限制边界的分析及如何设计好重心包线三个方面进行了较系统的分析研究,为...     

基于NSGA II算法分布度改进的ATREX发动机性能优化方法研究

为使飞行轨迹上膨胀式空气涡轮冲压发动机(Air Turbo Ramjet Expander, ATREX)推力满足飞行器要求,同时比冲为对应推力下的最优值,基于改进分布度的NSGA II算法建立了以推力、比冲为优化目标的ATREX多目标优化模型。本文首先提出了基于个体优化目标间直线距离的筛选函数,改善了NSGA II算法优化结果的分布度;然后基于改进的NSGA II算法建立了ATREX性能多目标优化模型,获得了地面状态发动机推力、比冲最优解。在优化结果分布度接近前提下,与基于原NSGA II算法建立的ATREX性能多目标优化模型对比,基于改进NSGA II算法建立的优化模型所需初始种群个数及迭代时间均下降30%左右。     

考虑排放影响的飞机多学科优化设计

随着民用航空运输业的发展,飞机对气候环境的影响越来越受到重视。为了满足未来飞机设计中经济性和环保性等指标,有必要在飞机概念设计阶段综合考虑成本和排放的影响。本文使用全球平均温度变化作为衡量飞机排放对气候影响的标准,分析了飞机巡航高度和速度对于排放物的影响。进一步,通过整合气动、重量、成本和排放等学科模型,建立了飞机概念设计阶段的多学科优化框架。基于该优化框架,以机翼平面形状、飞行速度和高度等参数为优化变量,分别以排放最小和成本最低为目标,进行了单目标和多目标优化设计研究。Pareto最优前沿的优化结果显示,单位排放成本的高低会影响成本相对于排放性能的变化趋势。     

旋转机翼飞机旋翼飞行动力学模型及配平

论述和建立了旋转机翼飞机在旋翼飞行模式下,低速前飞时飞机的飞行动力学模型。根据飞行特点,建立了低速前飞情形下的简化飞行动力学模型。针对旋转机翼飞机的旋翼特点,在建立模型时,考虑了旋翼旋转引起的下洗流对机体的影响;研究了旋转机翼飞机在低速前飞时的配平,提出了一种简化的计算方法,并以某样机为例,建立模型并配平,验证了模型的正确性;最后,研究了重心位置对前飞时纵向操纵和俯仰姿态的影响。     

三翼面CRW飞机纵向最优配平点研究

从飞行性能和控制效能两种优化角度,对三翼面鸭式旋转机翼(CRW)飞机的配平情况进行了研究。采用了物理意义明确的数学方法对CRW飞机进行配平计算,并用两种优化方法对配平状态进行了优化,以得到目标函数下的最优配平状态(最优配平点)。同时验证气动导数估算方法,为CRW飞机的进一步研究奠定了基础。     

先进战斗机纵向飞行特性与放宽静稳定度研究

放宽静稳定度在先进战斗机设计领域已获得广泛应用,与其相关的主动控制技术仍有进一步研究的价值,需要对放宽静稳定度对飞机纵向飞行性能的影响进行更全面的分析。以重心后移作为放宽静稳定度的方式,分析放宽静稳定度与某型战斗机俯仰力矩系数的关系,构建战斗机非线性模型并进行开环特性分析,在此基础上,分析放宽静稳定度对飞机运行平衡点的影响机理,对战斗机非线性模型进行线性化,并分析放宽静稳定度对飞机纵向线性模型阶跃响应特性和长短周期模态特性的影响。结果表明：放宽静稳定度可增大战斗机的俯仰力矩系数,提高飞机性能,但可能会使飞机本体模态特性变差,需要在设计控制率时予以考虑。     

翼身融合布局大型客机的重心分析

在翼身融合布局飞机的总体设计阶段,为评估飞机总体方案的重心范围,建立了重心分析模型.分析模型以翼身融合布局飞机的几何参数为基础,应用参数化方法快速完成客舱布置,以工程估算和代理模型两种方法完成飞机的重量估算并计算重心前后限,绘制重心云图.基于重心分析模型,在Matlab平台开发了重心分析程序.以555座级翼身融合布局飞机的总体方案为例子来验证本文开发的程序.结果表明本程序可快速实现BWB飞机的客舱布置和重心云图绘制,分析结果可为飞机的稳定性和操纵性评估提供重心数据.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.