共查询到20条相似文献,搜索用时 937 毫秒
1.
利用轴向拉伸/压缩和面内剪切载荷构建了一个相互作用函数,并将其通过幂级数展开成二次多项式,利用单轴试验测试的复合材料板屈曲载荷,基于数学原理和合理的假设,推导确定了多项式的各项待定系数,构建了轴向拉伸/压缩和剪切复合载荷下的复合材料板屈曲相关方程,从数学上理性地解决了传统屈曲相关方程不适用于复合材料板(尤其是非均衡铺层板)的问题。利用提出的相关方程预测了4种不同的非均衡铺层复合材料板在轴向拉伸/压缩和剪切载荷作用下的屈曲相关曲线,并与有限元特征值法的模拟结果进行了对比,两者具有很好的一致性,而对于传统相关方程,其铺层的非均衡性越大则预测误差越大。最后通过均衡铺层的复合材料加筋壁板的压剪复合试验进一步证明了提出的相关方程的有效性。 相似文献
2.
3.
4.
设计并制备了6种不同铺层结构的层合板,通过对其进行拉伸试验,研究了不同铺层角度及不同铺层比例对层合板拉伸性能的影响。通过试验获得了6种复合材料层合板在拉伸试验中所能承受的极限拉伸强度,损伤特征以及载荷-位移曲线。结果表明:随着偏轴角增大,复合材料层合板拉伸强度逐渐降低,当45°和90°铺层体积分数相同时,45°铺层的层合板拉伸强度高于90°铺层的层合板;[0°/45°]铺层在表面可有效减小分层面积,由于内部剪切作用[0/90°]铺层更易出现分层。验证了复合材料层合板可通过改变铺层角度设计其力学性能。 相似文献
5.
结合复合材料自动纤维铺放(AFP)技术,提出了一种交织铺层结构层合板成型方法,制备了非交织、交织正交层合板、非交织、两向交织和四向交织准各向同性层合板复合材料,并对交织铺层结构复合材料的层间结构和性能进行了分析研究。结果表明:交织正交层合板的拉伸、压缩、弯曲性能较非交织板性能均有所下降,但其层间剪切性能有明显提高,提高幅度约为16%;随着交织铺层组厚度的增加,交织层合板的拉伸性能呈下降趋势;交织层合板的开孔后拉伸、开孔后压缩和冲击后压缩强度保持率均高于非交织板,且冲击后分层损伤面积明显低于非交织板。交织铺层结构层合板相对于普通非交织层合板具有更好的损伤容限能力。 相似文献
6.
7.
通过对变刚度铺放路径进行数学建模,得到变刚度复合材料层合板的拓扑构型,对复合材料层合
板内每个离散单元的每个铺层进行纤维角度和铺层厚度的独立设计。然后将拓扑构型数据导入有限元分析软
件GENESIS 中,实现层合板铺层信息的可视化显示和拉伸性能的分析,得出层合板的弹塑性本构关系。通过
仿真数据与实验测试数据进行对比,得出在所构建的变刚度复合材料层合板模型上进行拉伸实验仿真的准确
度可达95% 。该方法不仅可以可视化地展现出铺放过程中发生重叠的位置、整个复合材料层合板的厚度分布
以及每层上铺放角的分布,还可对其在弹塑性范围内的拉伸性能进行精确仿真。 相似文献
8.
《西安航空技术高等专科学校学报》2021,(3)
为了研究不同铺层角和铺层厚度对复合材料层合板力学性能影响,通过转换复合材料刚度矩阵,得到复合材料层合板等效弹性常数,利用Matlab软件将计算复合材料层合板等效为计算等厚度各向异性板,研究不同铺层角对层合板力学性能影响;基于此等效方法,利用Fortran程序计算机翼剖面刚度,研究不同铺层厚度对层合板力学性能影响。结果表明:铺层角对复合材料层合板有较大影响,其中以45°铺层角作为最外层的层合板力学性能最佳,其次为90°和0°铺层角;随铺层厚度增加,机翼剖面的剪切刚度、弯曲刚度和扭转刚度几乎呈线性增大。研究成果为分析与设计飞机复合材料结构提供参考。 相似文献
9.
T尾是典型的民用飞机或运输机气动布局形式之一,寻求满足刚度、强度、稳定性约束条件下的结构轻重量是结构方案设计阶段的主要工作任务。利用复合材料弹性优化剪裁技术,运用Nastran软件系统,在细致建立有限元数值分析模型基础上,将梁和杆面积、板壳厚度以及复合材料铺层厚度作为优化变量,进行了结构优化,结果表明:结构各部件重量有所降低。为了考察给定的典型复合材料铺层角布置的合理性,引入复合材料的单元材料方向作为优化变量进行再次优化。优化结果表明:虽然增加材料方向作为优化变量能够使结构重量较初次优化有所降低,但是考虑到制造工艺要求,典型复合材料铺层布置也是合理的。 相似文献
10.
11.
A new analysis model for the effective stiffness of stiffened metallic panels under combined compression and shear stress 总被引:1,自引:0,他引:1
《Aerospace Science and Technology》2006,10(4):316-326
The paper deals with the analysis of the effective stiffness of stiffened metallic panels under combined compression and shear stress as used, e.g. in aircraft fuselages. An important criterion for sizing and certification of aircraft fuselages is the local and global buckling behaviour. For optimisation of stiffened metallic panels it is necessary to know the buckling and postbuckling behaviour as accurately as possible. Due to the fact that nonlinear FE analyses of a whole aircraft fuselage are too time consuming, a very fast quasi nonlinear FE analysis with a coarse mesh under consideration of semi-empirical methods for the effective skin-stiffness are used. At this point the effective stiffness method derived in this paper is used. Admittedly previous semi-empirical methods like the effective width method [J. Wiedemann, Leichtbau 1: Elemente, second ed., 1996; M.C.Y. Niu, Airframe Stress Analysis and Sizing, second ed., Commilit. Press Ltd., 1999] (only for pure compression load) or the method of Kuhn [P. Kuhn, J.P. Peterson, L.R. Levin, A summary of diagonal tension part I – methods of analysis, Technical Note 2661, NACA, 1952] (only for pure shear load) have disadvantages for the general combined compression and shear load case. This is improved in the current method.The first part of the paper deals with the realisation of the compression and shear test facility in a finite element model. The verification of the finite element model is important for subsequent parameter variations. The second part of the paper presents the approach of how to assess the effective skin-stiffness. In comparison to the paper in [M. Heitmann, P. Horst, D. Fitzsimmons, Effective stiffness of postbuckled stiffened metallic panels under combined compression and shear stress, J. Strain Anal. 38 (6) (2003) 534–555] many new parameters have been analysed. Therefore the new approach for the geometrically nonlinear analysis derived from the finite element results for combined compression and shear stress is considerably improved. At the end of the paper the great benefit of the new approach is shown. The results of very fast quasi nonlinear FE analyses under consideration of the new approach for the effective skin-stiffness on a coarse panel mesh agree well with the results of time expensive nonlinear FE analysis on a very fine panel mesh. Further studies are necessary to expand the new method to the influence of plasticity. 相似文献
12.
叶轮机械任意旋成面叶栅气动杂交命题矩函数型变分有限元解法 总被引:1,自引:1,他引:1
本文在文[1]、[2]提供的矩函数变分原理基础上建立了任意旋成面叶栅A类、B类杂交气动命题的变分有限元解法。文中用有限元法对相应的变分原理进行离散,所得非线性代数方程组迭代求解。由解出的矩函数计算流场速度、压力与密度,最后通过积分获得叶片未知边界形状。本文给出的计算结果显示了杂交命题方法的有效性和灵活性,它可以直接用于叶片改型与设计工作。 相似文献
13.
《中国航空学报》2016,(1):91-103
A theoretical nonlinear aeroelastic response analysis for a flexible high-aspect ratio wing excited by harmonic gust load is presented along with a companion wind tunnel test. A multidisci-plinary coupled numerical calculation is developed to simulate the flexible model wing undergoing gust load in the time domain via discrete nonlinear finite element structural dynamic analysis and nonplanar unsteady vortex lattice aerodynamic computation. A dynamic perturbation analysis about a nonlinear static equilibrium is also used to determine the small perturbation flutter bound-ary. A novel noncontact 3-D camera measurement analysis system is firstly used in the wind tunnel test to obtain the spatial large deformation and responses. The responses of the flexible wing under different static equilibrium states and frequency gust loads are discussed. The fair to good quanti-tative agreements between the theoretical and experimental results demonstrate that the presented analysis method is an acceptable way to predict the geometrically nonlinear gust response for flex-ible wings. 相似文献
14.
桨毂动力特性用八节点三维等参元与子空间迭代法进行数值模拟;进行了实验模态分析,从而确定了桨毂前六阶的固有频率及其对应的振型。 相似文献
15.
16.
17.
研究注塑模流动的数值模拟。用有限元-有限差分方法模拟非牛顿流体的压力场和温度场,用流体网格法(FAN)模拟熔体锋面的推进过程,这种方法具有通用性好和容易实现自动推进的优点。在486微机上对几个算例进行了模拟计算。比较了牛顿和非牛顿流体的流动特点和锋面推进自动处理的效果,得到了满意的结果。 相似文献
18.
本文把研究三波共振的弱非线性理论应用于平板边界层和平面Poiseuille流三维扰动的二次稳定性问题。其数值结果与文献[1]、[2]用Floquet形式的二次稳定性理论得出的结论是一致的。 相似文献
19.
20.
计算机翼跨声速压力分布的格林函数方法 总被引:1,自引:1,他引:1
本文给出一种用格林定理将跨声速小扰动速势方程化成积分方程式,然后进行数值求解的方法,文中对场元强度进行松弛迭代,一般只需20次左右即达收敛。算例表明,该方法结果与差分法结果一致。 相似文献