共查询到20条相似文献,搜索用时 31 毫秒
1.
一种对转压气机气动设计方法及其验证 总被引:1,自引:1,他引:1
结合附面层抽吸技术提出了一种高负荷对转压气机气动设计方法.在高负荷设计前提下,为避免在转动部件中进行附面层抽吸所带来的诸如强度等问题,利用基于动叶出口轴向速度提升的低反动度压气机气动设计原理,提升动叶出口轴向速度以确保动叶效率,附面层抽吸只在静叶中进行.利用该对转压气机气动设计方法,进行了一对转压气机气动设计验证.三维黏性数值模拟结果表明,在第一列转子与第二列转子叶尖切线速度分别为370m/s与350m/s的前提下,实现了总压比为5.85,效率为88%的两级对转压气机气动设计. 相似文献
2.
3.
轴流压气机近失速及旋转失速全通道数值模拟 总被引:1,自引:1,他引:0
为研究轴流压气机失速起始的动态过程,对某两级低速轴流压气机的第1级进行整环全通道模拟.结果表明:在近失速点流场中存在周向大尺度的速度波动,该波动与静子叶排首先出现的周向不均匀分布的叶背附面层分离密切相关,并且随着压气机进一步节流,波动幅值逐渐增大,最终诱发转子若干通道出现严重附面层分离,堵塞流道,压气机进入旋转失速.失速团完全发展后的转动频率与试验结果吻合较好. 相似文献
4.
5.
陆庆飞 《燃气涡轮试验与研究》2012,(2):12-17
采用数值模拟方法,研究了叶片吸力面开缝抽气方案对某高负荷跨声双级风扇性能和稳定工作范围的影响,分析了开缝位置及大小对抽吸气效果的影响。结果表明:通过静子叶片吸力面边界层抽气,可将边界层分离区的分离流引出,抑制或推迟边界层分离,减小因边界层分离带来的损失,从而改善风扇/压气机的气动性能,提高其稳定工作裕度;抽吸气效果与缝隙位置及大小等因素有关,风扇/压气机设计中应用抽吸气技术时须综合考虑以上各种因素的影响。 相似文献
6.
吸附式跨声速压气机叶栅流场数值模拟 总被引:5,自引:1,他引:4
使用MISES程序数值模拟了跨声速吸附式压气机叶栅流场, 重点研究了吸气量和吸气位置对跨声速压气机叶栅气动性能的影响.结果表明, 叶栅来流马赫数和方向一定时, 吸气位置和吸气量是相互关联的关键参数, 不同的吸气位置对应着不同的最佳吸气量, 且随着吸气位置向后缘远离激波, 最佳吸气量呈逐渐增大之势.从吸气对叶片吸力面边界层的影响效果分析, 理想的吸气位置应该是在靠近激波后附面层发展到一局部极大值即将进入过渡段的位置附近. 相似文献
7.
8.
在低速条件下,对不同吸气位置和吸气量的高负荷吸附压气机叶栅流场进行了实验研究,分析了吸气位置和吸气量对高负荷压气机叶栅流场的影响。结果表明,吸气位置和吸气量对高负荷吸气压气机叶栅流场影响显著,且在小吸气量下流场就有明显改善;附面层抽吸有效减小了积聚在吸力面角区的低能流体,流动分离被抑制,总损失下降明显,且抽吸对叶栅流场的影响随吸气量的增加而逐渐增大;在吸力面后部流动充分发展区域,采用附面层抽吸对抑制流动分离具有更好的效果。 相似文献
9.
10.
以某型轴流压气机为研究对象,对不同积垢程度的压气机流场进行了三维的CFD数值计算,对比分析积垢造成压气机性能损失的机理。结果表明:积垢对压气机流场的影响主要是导致叶片吸力面中部压力梯度比较大的区域附面层提前转捩,扩大尾迹区的低速回流区,增加叶栅的流动损失。 相似文献
11.
静叶吸气对某轴流压气机裕度影响的研究 总被引:1,自引:0,他引:1
运用Numeca CFD对某大弯度叶栅和某轴流压气机流动进行数值模拟,为减小由于边界层分离而带来的损失,拓宽稳定工作范围,提出叶片吸力面表面开缝抽气方案.综合研究开缝位置、开缝长度、及吸气量大小对流动分离结构和裕度的影响.结果表明通过静子叶片上边界层抽气引出分离区域的低能量气流,可以明显的改善气动性能,分离得到很好的抑制,稳定工作裕度得到了提高. 相似文献
12.
13.
单转子压气机设计状态出口叶尖通道中部、叶根吸力面角区和转子尾迹内具有较强的紊流脉动,泄漏涡是造成尖部气流掺混的主要因素。近失速状态通道内气流脉动明显增强,并沿周向和径向呈现出较大的梯度,叶尖通道中部的紊流强度分布证实了气流剧烈交混的发生,0.87 叶高和0.25 叶高吸力面附近的强紊流中心来源于叶背附面层分离形成的旋涡。在出口测量截面上紊流强度3 个分量的最大值,径向分量最大,轴向分量次之,切向分量最小。 相似文献
14.
《中国航空学报》2015,(4)
With the aim of deepening the understanding of high-speed compressor cascade flow,this paper reports an experimental study on NACA-65 K48 compressor cascade with high subsonic inlet flow.With the increase of passage pressurizing ability, endwall boundary layer behavior is deteriorated, and the transition zone is extended from suction surface to the endwall as the adverse pressure gradient increases.Cross flow from endwall to midspan, mixing of corner boundary layer and the main stream, and reversal flow on the suction surface are caused by corner separation vortex structures.Passage vortex is the main corner separation vortex.During its movement downstream, the size grows bigger while the rotating direction changes, forming a limiting circle.With higher incidence, corner separation is further deteriorated, leading to higher flow loss.Meanwhile, corner separation structure, flow mixing characteristics and flow loss distribution vary a lot with the change of incidence.Compared with low aspect-ratio model, corner separation of high aspect-ratio model moves away from the endwall and is more sufficiently developed downstream the cascade.Results obtained present details of high-speed compressor cascade flow,which is rare in the relating research fields and is beneficial to mechanism analysis, aerodynamic optimization and flow control design. 相似文献
15.
附面层抽吸对低雷诺数下压气机稳定性的影响 总被引:4,自引:0,他引:4
数值模拟了低雷诺数下附面层抽吸流动控制对跨声速压气机稳定性的影响。低雷诺数下附面层径向涡及其诱发的叶顶分离阻塞触发压气机流动失稳,通过在NASA Rotor 37跨声速轴流压气机转子叶片吸力面上设计抽吸槽,探讨了抽吸流动控制对低雷诺数下压气机性能和稳定性的影响.并对比分析了抽吸前后压气机流场特性的变化和抽吸流动控制提高低雷诺数下跨声速轴流压气机稳定性的作用机理。 相似文献
16.
Experimental investigation of a counter-rotating compressor with boundary layer suction 总被引:1,自引:0,他引:1
《中国航空学报》2015,(4)
This paper presents the aspirated modification of a dual-stage counter-rotating compressor which contains inlet guide vanes(IGVs), two counter-rotating rotors(R1, R2), and outlet guide vanes(OGVs).Uniform circular holes are circumferentially distributed over the rotors' tips on the shroud casing which are designed to remove the low-energy fluid near the shroud casing.OGVs are hollow blades with two slots designed on the suction side which can better control the flow on the suction surface through boundary layer suction.Related works about the experiments have been carried out since June 2012 and the effect of flow suction on the performance of the compressor is investigated in detail.Characteristic lines at a 70% corrected rotating speed are tested and those with higher rotating speeds will be studied in the near future.Experimental results indicate that boundary layer suction can improve the compressor characteristics and the best suction methodology varies along the operating line.At the near stall condition, suction from the R2 tip region can obviously increase the efficiency and the total pressure ratio, as well as improve the flow capacity.Isentropic efficiency can be maximally increased by 4.24% with an increase of 1.94% in massflow under a suction flow of 160 m3/h.Suction at the R1 position with a suction rate below 0.35% in a high flow situation can make the performance of the compressor better than others.Around the peak efficiency point, boundary layer suction from the slots of OGVs is the best choice in improving the efficiency, but it causes a 0.1% loss in the total pressure ratio. 相似文献
17.
弓形静子提高压气机抗旋流畸变能力研究 总被引:1,自引:1,他引:0
为降低旋流畸变对轴流压气机性能和稳定性的影响,对双级低速轴流压气机的第1级静子进行了3种不同正弯角的弓形叶片设计.采用整环三维定常计算方法,研究了对涡旋流下压气机的性能和稳定性.结果表明:静子采用合理的正弯曲设计能够提高压气机抗对涡旋流的能力.正弯曲弓形静子能够降低端壁区域的负荷,抑制各排叶片叶根区域吸力面附面层分离的形成以减小损失、提高效率和总压比.静叶弯角为10°时峰值效率增加1.5%,失速边界点流量减小6.95%.流量为18.5kg/s时,效率、总压比分别增加1.7%和0.03%.当弯角过大时,叶中区域负荷上升且摩擦损失增大,反而不利于效率和总压比的提升. 相似文献
18.
19.
超声速压气机转子叶片吸力面抽气抑制附面层分离的机理 总被引:9,自引:5,他引:4
针对压气机叶片在高负荷及非设计工况下经常出现的附面层分离状况, 采用数值方法研究了叶片吸力面不同位置、不同吸气量时附面层抽吸对压气机转子气动性能的影响.数值结果表明:抽吸位置对抽吸效果有重要的影响, 通过在分离区下游一定位置处抽吸, 能够很好的抑制附面层分离, 改善气流在大分离点处的剧烈变化, 减少流动损失, 使得级效率和压比均有显著的提高;而在分离区上游或者分离区下游的较远处开缝抽吸, 则效果不理想.吸气量对抽吸效果也有一定影响, 存在一个最佳吸气量, 吸气量过大或者过小都会对结果产生不利影响. 相似文献