迟滞非线性二元机翼颤振特性分析

 采用多项式迟滞非线性模型建立二元机翼气动弹性运动方程，并用数值积分法进行求解。通过系统响应振幅随来流速度变化的分叉图和频谱分析发现，俯仰方向由于含有非线性因素，振动中的高阶分量随速度提高不断增加，并引起高次分叉。重点研究“机翼/空气”质量比以及“沉浮/俯仰”两个自由度的自然振动频率比对非线性颤振速度边界的影响，并提出可以通过提高自然振动频率比来减小迟滞非线性因素的不利影响。     

非线性二元机翼气动弹性近似解析研究

 建立了不可压流动中多项式迟滞非线性二元机翼的气动弹性运动方程,然后利用谐波平衡法进行了求解。与数值积分结果比较分析表明,在系统发生二次分叉以前,谐波平衡法可以准确地预测极限环振荡的频率和振幅,通过频谱分析与时间响应历程讨论了谐波平衡法产生误差的原因。另外还研究了弹性轴位置对颤振特性的影响,随着弹性轴不断靠近翼弦中点,俯仰振幅不断增大,而沉浮振幅则存在一个极小值点。     

带有气动及结构非线性的二元机翼颤振分析

研究了翼型在低马赫数条件下的非定常气动特性,从翼型表面气流运动的角度对Leishman-Beddoes(L-B)模型进行了修正,并在此基础上建立了适合低马赫数颤振研究且带有气动及结构非线性的二元机翼气弹系统分析模型.对比低马赫数翼型气动载荷试验结果表明对L-B模型的修正是有效的,且机翼颤振试验结果亦验证了二元机翼气弹分析模型.研究结果表明:二元机翼气弹系统的失速颤振与初始变距角和来流速度密切相关,且耦合的三次非线性变距和浮沉刚度是造成系统呈现准周期运动的主要原因.      

不同迎角的翼型气弹特性风洞实验研究

基于可在不同迎角下作沉浮、俯仰两自由度运动的翼段振动装置,在低速风洞中分别针对普通薄翼型NA-CA0012和风力机翼型NREL S809进行气动弹性测试,得到不同实验状态的气动弹性振动时域响应。分别观察到经典颤振和失速颤振现象,并证明了迎角改变对两种翼型颤振特性的影响。     

Reliability and Sensitivity Analysis of Transonic Flutter Using Improved Line Sampling Technique

The improved line sampling (LS) technique, an effective numerical simulation method, is employed to analyze the probabilistic characteristics and reliability sensitivity of flutter with random structural parameter in transonic flow. The improved LS technique is a novel methodology for reliability and sensitivity analysis of high dimensionality and low probability problem with implicit limit state function, and it does not require any approximating surrogate of the implicit limit state equation. The improved LS is used to estimate the flutter reliability and the sensitivity of a two-dimensional wing, in which some structural properties, such as frequency, parameters of gravity center and mass ratio, are considered as random variables. Computational fluid dynamics (CFD) based unsteady aerodynamic reduced order model (ROM) method is used to construct the aerodynamic state equations. Coupling structural state equations with aerodynamic state equations, the safety margin of flutter is founded by using the critical velocity of flutter. The results show that the improved LS technique can effectively decrease the computational cost in the random uncertainty analysis of flutter. The reliability sensitivity, defined by the partial derivative of the failure probability with respect to the distribution parameter of random variable, can help to identify the important parameters and guide the structural optimization design.     

二元非线性机翼随机动力学行为

 为考查在高斯白噪声作用下二元机翼随机颤振动力学行为,采用数值仿真的方法对其进行了研究。首先把机翼简化成一个具有扭转和上下自由度的平板,其中扭转弹簧具有3次非线性刚度,同时假设空气是线性不可压的而且气动力是定常的,再对任意运动和高斯白噪声作用下的机翼进行建模。其次采用了蒙特卡罗仿真来求解随机微分方程的数值解,根据数值解结果进行统计分析,计算出最大Lyapunov指数。最后得出：在随机激励作用下机翼的动力学行为与确定性颤振相比有很大差异,同时随机颤振点提前于确定性颤振点。     

机翼颤振的区间有限元分析(英文)

The influences of uncertainties in structural parameters on the flutter speed of wing are studied. On the basis of the deterministic flutter analysis model of wing, the uncertainties in structural parameters are considered and described by interval numbers. By virtue of first-order Taylor series expansion, the lower and upper bound curves of the transient decay rate coefficient versus wind velocity are given. So the interval estimation of the flutter critical wind speed of wing can be obtained, which is more reasonable than the point esti- mation obtained by the deterministic flutter analysis and provides the basis for the further non-probabilistic interval reliability analysis of wing flutter. The flow chart for interval fmite element model of flutter analysis of wing is given. The proposed interval finite element model and the stochastic finite element model for wing flutter analysis are compared by the examples of a three degrees of freedom airfoil and fuselage and a 15° sweptback wing, and the results have shown the effectiveness and feasibility of the presented model. The prominent advantage of the proposed interval finite element model is that only the bounds of uncertain parameters are required, and the probabilistic distribution densities or other statistical characteristics are not needed.     

机翼对螺旋桨发动机旋转颤振的影响研究

为了研究机翼对螺旋桨发动机旋转颤振的影响规律,揭示其影响机理,通过片条理论计算螺旋桨气动载荷,在MSC.NASTRAN软件平台上进行二次开发,对不同结构参数的吊舱-螺旋桨系统和机翼-吊舱-螺旋桨系统进行了旋转颤振分析。研究表明,机翼结构的弹性会大幅降低发动机俯仰模态频率,而小幅降低发动机偏航模态频率,从而改变两模态频率之差,影响模态耦合的程度,进而改变旋转颤振速度。另外,当发动机的运动与机翼翼面的运动耦合紧密时,机翼翼面的气动载荷能够显著提高发动机的旋转颤振速度。     

二维机翼二自由度跨音速颤振分析

 <正> On the assumption that airfoils take small amplitude ha-rmonic oscillating and middle reduced frequency, the two-dimensional, inviscid, small-disturbance nonlinear unsteady transonic flow equation can be split into two parts. One is the nonlinear steady small-disturbance equation, the other is the time-linearized unsteady small-disturbance equation. The steady equation is solved by Carlson code. The unsteady equation is solved by integral method. The standard v-g method is used to solve the flutter eigenvalue equations. A transonic flutter analysis is performed for a NACA 64A006 airfoil with pitching and plunging degrees of freedom.The Mach numbers considered are 0.7, 0.8, and 0.85. The aerodynamic coefficients are obtained by the above method. For each Mach number, the flutter speed and the corresponding flutter reduced frequencies are achieved by varying the airfoil-airmass ratio, plunge-pitch frequency ratio. The results are compared with other computational method and good agreement has been observe     

操纵面对跨声速机翼气动弹性特性的影响

 运用基于非定常CFD的气动力辨识技术,得到跨声速非定常气动力降阶模型。耦合结构动力学方程,建立了基于状态空间的跨声速气动弹性分析模型。分析了典型三自由度二元机翼的颤振边界,分析结果与CFD/CSD直接耦合方法吻合。然后研究了操纵面结构参数（固有频率和重心位置）对跨声速气动弹性特性的影响。研究发现,一些传统的结构设计准则和颤振排除技术未必适用于跨声速状态;操纵面偏转模态常常成为诱发跨声速颤振的主要模态;经典的质量平衡技术可能会降低跨声速气动弹性系统的稳定性。     

考虑间隙非线性的控制舵非线性气动弹性分析

间隙结构的气动弹性系统非线性颤振问题是飞行器气动弹性力学工程领域的研究热点和难点,研究 考虑间隙非线性的控制舵系统的气动弹性特性具有重要意义。基于最小状态拟合方法获得时域降阶气动力模 型,并通过Lagrange方程获得系统非线性气动弹性方程;对比分析三种不同非线性控制舵系统的极限环颤振 及非线性动力学响应特性,并与等效线化法和时域仿真的结果进行一致性对比。结果表明:俯仰和扑动弹簧刚 度的变化对系统颤振边界有显著影响,当俯仰和扑动两个方向同时含有间隙非线性时,系统在线性颤振速度内 存在倍周期、混沌等复杂非线性动力学现象。     

Nonlinear aeroelastic analysis of airfoils: bifurcation and chaos

Different types of structural and aerodynamic nonlinearities commonly encountered in aeronautical engineering are discussed. The equations of motion of a two-dimensional airfoil oscillating in pitch and plunge are derived for a structural nonlinearity using subsonic aerodynamics theory. Three classical nonlinearities, namely, cubic, freeplay and hysteresis are investigated in some detail. The governing equations are reduced to a set of ordinary differential equations suitable for numerical simulations and analytical investigation of the system stability. The onset of Hopf-bifurcation, and amplitudes and frequencies of limit cycle oscillations are investigated, with examples given for a cubic hardening spring. For various geometries of the freeplay, bifurcations and chaos are discussed via the phase plane, Poincaré maps, and Lyapunov spectrum. The route to chaos is investigated from bifurcation diagrams, and for the freeplay nonlinearity it is shown that frequency doubling is the most commonly observed route. Examples of aerodynamic nonlinearities arising from transonic flow and dynamic stall are discussed, and special attention is paid to numerical simulation results for dynamic stall using a time-synthesized method for the unsteady aerodynamics. The assumption of uniform flow is usually not met in practice since perturbations in velocities are encountered in flight. Longitudinal atmospheric turbulence is introduced to show its effect on both the flutter boundary and the onset of Hopf-bifurcation for a cubic restoring force.     

非线性机翼极限环颤振的研究

在定常空气动力的作用下,对含立方非线性刚度的二元机翼颤振系统的极限环颤振进行了研究.应用中心流形理论将原四维系统降为二维,采用后继函数法对分岔点类别进行了定性的分析,从而确定平衡点的性质,并应用范式理论对分岔点处中心流形约化方程进行化简,进而研究了系统参数对极限环颤振的稳定性以及幅值的影响.     

仿生正弦前缘对翼面动态失速的影响

动态失速导致叶片气动载荷急剧变化，造成振动载荷激增，桨叶寿命大幅衰减。针对动态失速问题，从座头鲸胸鳍在动态倾转下取得良好的流动特性获得启示，据此模化出仿生正弦前缘翼面（包含3种波峰和2种波长），旨在实现动态失速控制。借助三维非定常数值模拟方法，采用运动网格技术，基于SC1095旋翼翼型，研究了仿生前缘动态失速流动控制机理及运动参数和来流速度的影响。结果表明：正弦前缘大幅度降低俯仰力矩系数峰值和阻力系数峰值；前缘波峰越大、波长越小，阻力系数峰值与俯仰力矩系数峰值的抑制效果越明显，虽然升力系数峰值减小，但其减小量远小于前两者，例如其中一种仿生翼使俯仰力矩系数峰值减小了47.7%，阻力系数峰值减小了36.4%，升力系数峰值减小14.1%；在最大迎角附近，正弦前缘能够缓和失速特性，使载荷变化更为平缓；在高平均迎角、低俯仰频率、低马赫数下，仿生翼动态失速控制效果更强，相比较而言迎角振幅的影响较小。     

不同振动形式下的翼型失速特性

通过求解雷诺平均Navier-Stokes方程,研究了翼型在强迫振动和自然结构振动下的大迎角流场特性,尤其是失速迎角附近的流场和气动特性.研究结果表明:在接近颤振临界速度情况下结构自然振动可以引起翼型大尺度的分离,导致失速分离涡提前出现;强迫性的沉浮运动和俯仰运动在一定幅度下也可以引起失速性质的大分离,而且沉浮和俯仰振动的频率和振幅都是影响翼型大尺度分离的重要因素.     

用规范型直接法研究立方非线性机翼的颤振

研究了在不可压缩流中具有立方非线性俯仰刚度的二元机翼的颤振问题。首先，对系统平衡点进行了特征值分析，得到在Hopf分岔点附近的颤振参数方程。然后，应用规范形直接法的Maple推导程序，计算得到Hopf分岔的规范形．并数值模拟验证了超、亚临界类型分岔情形下响应对初值的依赖性。最后．分析了线性和非线性刚度系数对颤振响应拓扑结构的影响。     

Optimization design of airfoils under atmospheric icing conditions for UAV

Natural ice accretion on the lifting surface of an aircraft is detrimental to its aerodynamic performance, as it changes the effective streamlined body. The main focus of this work considers the optimization design of airfoils under atmospheric icing conditions for the Unmanned Aerial Vehicle(UAV). The ice formation process is simulated by the Eulerian approach and the three-dimensional Myers model. A three-equation turbulence model is implemented to accurately predict the stall performance of t...     

某型飞机颤振试飞数据的模态参数识别

 地面模态试验表明某机型的机翼对称一阶弯曲与发动机对称俯仰频率比较接近。为了检查这两阶模态是否会在设计的飞行速度下引起颤振,在不同飞行速度下利用脉冲激励方式测量了频响函数。这组频响函数不仅在关心频段存在密集模态,而且受噪声干扰严重。采用了修正的整体正交多项式识别方法(引入额外的加权函数来降低估计的方差,分子和分母引入采用相同的正交基) , 对这组数据进行了模态分析,并利用一些先验信息和规则从拟合模态鉴别出真实模态。研究表明机翼对称一弯和发动机对称俯仰的两阶模态的频率随速度增加而趋近,两阶阻尼比均随速度增加而下降,但是在设计速度下,模态参数离颤振有较大裕量。     

间隙约束二元翼段系统分岔与多解共存现象分析

研究了分段刚度描述的间隙约束二元翼段气动弹性系统,取俯仰角最大幅值处为类Poincaré截面,数值计算得到了系统随飞行速度变化的分岔图,发现飞行速度在Ma=0.71~0.75属于跨临界颤振区,而在Ma=0.75~0.95发生极限环震荡.同时通过构造极限环震荡的四维Poincaré映射分析了极限环震荡的稳定性,结合稳定性和运动流形理论,得到极限环震荡的吸引域一般位于极限环内部并用数值方法进行了验证.且跨临界颤振速度区域中存在多种分岔形式以及多解共存现象,例如由双周期运动直接通向混沌、多周期运动与双周期运动共存现象,振动幅值也存在跳跃现象.     

非线性气动弹性模型参考自适应控制

 首先将含有前/后缘双控制面二元机翼的动态方程以状态空间形式描述,然后考虑俯仰方向的迟滞非线性模型存在参数不确定性的情况下,利用Lyapunov稳定性理论进行了结构化模型参考自适应控制律设计。仿真结果显示：所设计的控制律能够使开环不稳定的气动弹性系统快速地达到稳定状态。由于最大控制面偏转的存在,来流速度较高时闭环系统仍会发生颤振;根据控制面最大偏转的不同取值,文中给出了闭环临界颤振速度的变化曲线。