The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.     

Non-destructive Evaluation of Composite Pressure Vessel by Using FBG Sensors

In recent years, advanced composite structures are used extensively in many industries such as aerospace, aircraft, automobile, pipeline and civil engineering. Reliability and safety are crucial requirements posed by them to the advanced composite structures be- cause of their harsh working conditions. Therefore, as a very important measure, structural health monitoring (SHM) in-service is defi- nitely demanded for ensuring their safe working in-situ. In this paper, fiber Bragg grating (FBG) sensors are surface-mounted on the hoop and in the axial directions of a FRP pressure vessel to monitor the strain status during its pressurization. The experimental results show that the FBG sensors could be used to monitor the strain development and determine the ultimate failure strain of the composite pressure vessel.     

Large Amplitude Flexural Vibration of the Orthotropic Composite Plate Embedded with Shape Memory Alloy Fibers

研究了形状记忆合金(SMA)纤维混杂复合材料大挠度层合板的非线性自由与受迫振动特性。基于描述SMA力学行为的Brinson理论以及层合板材料性能预测的混合率,建立了SMA纤维混杂复合材料大挠度层合板的本构方程,基于对称层合各向异性弹性板的非线性理论,建立了以横向挠度和应力函数表示的板的横向振动方程和相容方程。采用Galerkin近似解法将振动方程化为时间变量的含有3次非线性项的Duffing型常微分方程,采用谐波平衡法(HBM)获得系统的固有频率方程和强迫振动稳态频率响应方程。数值计算表明,非线性板自由振动频率比与激励温度的关系具有与线性板相同的特征,马氏体相向奥氏体相转变阶段温度对板的振动频响特性曲线的影响最显著,同时也讨论了SMA纤维含量、板的纵横比以及自由振动幅值对板的非线性频率比的影响。     

TMR-BITE16位单片机容错系统SCFT

介绍~种以16位单片机MCS-96为基础的TMR-BITE(也称TMR-Duplex-Simplex)容错计算机系统SCFT。该系统具有故障检测、恢复和逐步降级的功能;特点是结构紧凑、体积小、可靠性高和表决时间开销小等,能广泛适用于航空航天技术,飞控系统和自动控制系统。文中详细论述了SCFT系统的工作原理、设计方法、同步技术和通讯方式,并对系统的可靠性进行了分析。     

GA-Based Model Predictive Control of Semi-Active Landing Gear

Semi-active landing gear can provide good performance of both landing impact and taxi situation, and has the ability for adapting to various ground conditions and operational conditions. A kind of Nonlinear Model Predictive Control algorithm （NMPC） for semi-active landing gears is developed in this paper. The NMPC algorithm uses Genetic Algorithm （GA） as the optimization technique and chooses damping performance of landing gear at touch down to be the optimization object. The valve＇s rate and magnitude limitations are also considered in the controller＇s design. A simulation model is built for the semi-active landing gear＇s damping process at touchdown. Drop tests are carried out on an experimental passive landing gear systerm to validate the parameters of the simulation model. The result of numerical simulation shows that the isolation of impact load at touchdown can be significantly improved compared to other control algorithms. The strongly nonlinear dynamics of semi-active landing gear coupled with control valve＇s rate and magnitude limitations are handled well with the proposed controller.     

基于亚燃的高超声速冲压发动机内流道研究

为了研究亚燃冲压发动机在高超声速条件下工作的性能,采用总体性能计算方法和流体力学仿真对基于突扩燃烧的高马赫数亚燃冲压发动机内流通道进行匹配设计研究,得到了其速度特性和调节特性。结果表明,设计出的亚燃冲压发动机在高超声速范围内性能良好,能够正常工作。在接力点处,马赫数Ma=3.5,高度H=12km,得到最大推力系数为0.649,此时比冲为13 801.2N·s/kg;在巡航点处,Ma=5.0,H=21km,发动机余气系数α=1.8时,得到推力系数为0.370,此时最大比冲为12 574.0N·s/kg。研究认为,最大飞行马赫数为5~6的高超声速冲压发动机采用亚燃是可行的。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

基于飞机油箱模型形状特征油量测量切片步长选择方法研究

 在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明：该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。     

Some features of disturbed rotational motion of a satellite with a strong onboard magnet

A disturbed rotational orbital motion of an asymmetrical satellite with a strong magnet in the geomagnetic field is considered. It is shown that operating disturbances result in appearing of non-resonant phenomena in the satellite rotation caused by resonance effects.     

晶体生长方向对亚快速凝固结晶形貌的影响

采用区域熔化定向凝固装置,对冷却速度在１３～１３０Ｋ／ｓ范围内Ｎｉ－５％Ｃｕ合金的结晶形貌研究表明：在温度梯度ＧＬ３００Ｋ／ｃｍ条件下,晶体生长速度υ为５００μｍ／ｓ时,不同结晶取向的晶粒其结晶形貌不同。以＜１００＞方向生长的晶粒为树枝晶组织;以＜１２０＞方向生长的晶粒为细胞晶组织。当υ为８００μｍ／ｓ时,不同结晶取向的细胞晶间距不同。以＜１００＞方向生长的细胞晶间距是２８μｍ;以＜２１１＞方向生长的细胞晶间距是１６. ５μｍ。相同凝固条件下,同一晶粒内不同取向的分枝,结晶形貌不同。亚快速凝固条件下,树枝晶生长的生长方向已不完全按＜１００＞方向择优取向,细胞晶生长的择优取向性被抑制。     

二维翼段颤振的μ控制

 采用超声电机作为作动器来实现含控制面的翼段颤振鲁棒抑制。针对作者设计的二维翼段颤振主动抑制系统，通过理论与实验相结合的方法，建立了考虑沉浮方向阻尼和作动器模型参数不确定性的控制系统模型，设计了μ控制器，并对控制器做了降阶处理。数值仿真和风洞试验表明，μ控制器可有效地抑制颤振的发生，将颤振临界速度提高23.4%。相对于H_∞控制器，μ控制器的控制效果和鲁棒性更好。