柔性氧化硅气凝胶隔热复合材料的制备和性能

以正硅酸乙酯为原料,高硅氧纤维为增强体,采用氨水催化一步法制备了柔性的纤维增强氧化硅气凝胶隔热复合材料。当pH=7时,气凝胶的比表面积最大;水含量增大,比表面积降低;乙醇含量增大,比表面积增大,EtOH/TEOS(摩尔比)大于10以上,比表面积增加不明显,趋于稳定。以比表面积较大的气凝胶作为基体的柔性复合材料常温热导率为0.031 W/(m.K)[纯高硅氧纤维毡为0.044 W/(m.K)]。该柔性隔热材料安装方便,特别适用于大面积、不规则形状的包覆隔热。     

基于甲基三甲氧基硅烷/正硅酸乙酯的聚碳酸酯耐磨涂层

以甲基三甲氧基硅烷(MTMS)水解聚合产物作为主要成膜物质,引入正硅酸乙酯(TEOS)水解产物硅溶胶作为无机增强物,采用溶胶凝胶法在聚碳酸酯(PC)表面形成耐磨涂层。结果表明:PC表面形成了Si—O—Si的交联网络结构。通过测试耐磨实验前后光学性能的变化研究表面涂覆涂层的聚碳酸酯的耐磨性能与涂层组分之间的关系。当涂层原料MTMS和TEOS的摩尔比为2∶1时,聚碳酸酯的耐磨性能达到最优,500次摩擦后雾度为13.22%,为纯PC的56.21%。     

热处理对纤维增强SiO2气凝胶性能的影响

采用溶胶一凝胶法制备了纤维增强SiO_2气凝胶隔热材料,对基体SiO_2气凝胶及复合材料进行不同温度的热处理.利用扫描电镜、比表面积和孔径测试仪和导热仪等手段对处理后材料的微观结构和常温隔热性能进行表征.结果表明:复合材料经低于700℃处理后,材料基体的微观结构略有变化,常温隔热性能基本保持不变;经1000℃处理的纳米结构发生了烧结、纳米孔含量减少,常温隔热性能显著降低.     

隔热瓦/SiO2气凝胶复合材料的制备与性能

以莫来石纤维和玄武岩纤维为主要成分,以硅溶胶为黏接剂制备的隔热瓦作为增强体,真空浸渍SiO_2溶胶后经过凝胶、老化和超临界干燥工艺制备隔热瓦/SiO_2气凝胶复合材料,并对材料的微观结构、热稳定性和隔热性能进行了表征。结果表明:由于玄武岩纤维具有更细的直径和含有一定量的红外辐射抑制成分,随着隔热瓦中玄武岩纤维质量分数的增加,复合材料的室温热导率从63 mW/(m·K)降至47 mW/(m·K),在热面600℃持续15 min条件下的背面温度从200℃降至117℃,有效地提高了复合材料的隔热性能;但因玄武岩纤维的使用温度显著低于莫来石纤维,复合材料的高温线收缩率增大,热稳定性有所下降。     

二氧化硅气凝胶原位填充聚酰亚胺泡沫的结构及隔热性能研究

以超轻质开孔柔性聚酰亚胺泡沫为基体,采用溶胶凝胶工艺制备了一系列二氧化硅气凝胶原位填充的聚酰亚胺复合泡沫。复合泡沫密度10~100 kg/m³可调,厚度1~ 400 mm可调,最大宏观尺寸可达1 m×1 m。对其泡孔结构、隔热性能、热性能进行了系统表征,分析了二氧化硅气凝胶原位填充聚酰亚胺泡沫的隔热机理。结果表明：二氧化硅气凝胶的引入,可有效降低复合泡沫室温热导率,提高其隔热性能;随着二氧化硅气凝胶含量的增加,聚酰亚胺复合泡沫的热导率由38.8 mW/（m·K）降低至19.6 mW/（m·K）;热端温度300 ℃时,复合泡沫热导率仅为61.1 mW/（m·K）;填充二氧化硅气凝胶后,聚酰亚胺复合泡沫热稳定性大大提高,在900 ℃下热失重残留量约为80%。     

氧化铝气凝胶复合高温隔热瓦的制备及性能

以陶瓷纤维制成的高温隔热瓦为骨架,真空浸渍氧化铝溶胶,再经过凝胶、老化和超临界干燥制备出氧化铝气凝胶复合高温隔热瓦,研究了其在不同温度处理后(最高温度1 400℃)的微观结构、隔热和力学性能。结果表明:气凝胶复合高温隔热瓦在1 400℃保温30 min后线收缩率仅为2%;随着热处理温度升高,气凝胶颗粒发生熔并、长大,气凝胶从填充纤维空隙到不断收缩,但对纤维骨架没有明显影响;隔热瓦的室温、高温热导率均显著降低;在热面1 400℃的背温测试中,复合后材料的背温从945℃降到870℃;复合后隔热瓦的力学性能略有增加;但是1 200~1 400℃的压缩强度下降较大。可见,气凝胶复合高温隔热瓦可改善其隔热性能,但在高温下力学性能下降。     

耐高温透波气凝胶复合材料性能

针对高马赫数飞行器中恶劣热环境对透波隔热材料的需求,采用溶胶-凝胶方法,以透波型石英纤维为增强体,通过超临界干燥及后处理制备透波二氧化硅气凝胶复合材料;并采用扫描电子显微镜、平板导热仪、石英灯辐射加热及万能电子试验机等手段对材料的微观形貌结构、隔热性能、耐温性及力学性能进行了表征。结果表明:二氧化硅透波气凝胶复合材料有良好的介电性能,介电常数在1.28~1.39可调、损耗角正切≤0.005;耐温性≥1 100℃、室温热导率≤0.02 W/(m·K);具有较好的力学性能,能保证飞行器在恶劣飞行环境中的通讯、遥测、制导等系统的正常工作。     

柔性SiO2 气凝胶的制备

以甲基三乙氧基硅烷为前驱体,通过溶胶-凝胶法和超临界干燥制备块状柔性SiO2气凝胶.研究了前驱体浓度对材料化学组成、微观结构及柔韧性、热稳定性的影响.结果表明,甲基的存在降低了分子网络的交联密度,赋予了材料柔韧性.随着前驱体浓度降低,微观结构中颗粒堆积紧密程度下降,材料的柔韧性增强;同时分子中硅羟基增多,热稳定性提高.     

柔性二氧化硅气凝胶综述

二氧化硅气凝胶具有低密度、高孔隙率、高比表面积、低导热性等特点,但存在强度低、韧性差等缺陷.在此基础上,柔性二氧化硅气凝胶通过改进传统二氧化硅气凝胶的制备工艺表现出了更优的力学性能与适用性.本文综述了国内外柔性二氧化硅气凝胶的最新研究进展,分析对比了不同类型气凝胶的性能参数;重点介绍了柔性二氧化硅气凝胶常用的制备方法,...     

ZrC/SiC多组元改性C/C复合材料的制备及性能研究

以炭毡作为纤维增强体,采用化学气相渗透工艺研制出低密度的C/C复合材料,进而以低密度炭/炭复合材料为预制体,采用聚碳硅烷和有机锆前驱体作为复相陶瓷前驱体,采用先驱体浸渍裂解工艺成功制备出ZrC/SiC多组元改性C/C复合材料试样。借助万能电子试验机和扫描电镜进行材料的力学性能和微观结构分析。结果表明:包含ZrC颗粒的SiC相双组元弥散分布在C/C复合材料基体中,且随着前驱体中有机锆含量的增加,力学性能出现先升后降的趋势,当有机锆前驱体质量分数为25%时,改性C/C复合材料弯曲强度和弯曲模量较优,分别为240.61MPa和17.25GPa。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.