共查询到20条相似文献,搜索用时 62 毫秒
1.
尹昌平%肖加余%曾竟成%李建伟%刘钧 《宇航材料工艺》2008,38(5)
以GA327改性芳胺为固化剂,对应用于RTM工艺的E-44环氧树脂体系的流变特性进行了研究。在黏度实验和DSC热分析实验的基础上,依据双阿累尼乌斯方程建立了与实验数据较为吻合的流变模型。结果表明:E-44/GA327体系在60~85℃内黏度低于800mPa·s,且低黏度保持时间大于20min,在75~85℃内黏度低于300mPa·s的时间可达10min。所得到的模型可揭示树脂在不同工艺条件下的黏度变化规律,定量预报树脂的低黏度平台工艺窗口,为该树脂RTM工艺窗口的确定以及RTM工艺参数优化提供科学依据。 相似文献
2.
石东%石凤%段跃新%梁志勇 《宇航材料工艺》2005,35(2):52-56
建立树脂体系的流变模型可以预测体系RTM工艺窗口。采用黏度计等试验手段与双阿累尼乌斯经验模型理论分析相结合方法,研究不同恒温温度、不同溶剂含量的酚醛树脂黏度的变化规律,建立了酚醛树脂体系的化学流变模型,得到溶剂含量与模型参数之间的变化规律。研究结果可以对体系黏度进行预报,为RTM工艺的顺利实施以及工艺参数的准确制定奠定了基础。 相似文献
3.
4.
5.
RTM专用双马来酰亚胺树脂体系流变特性及模拟分析研究 总被引:4,自引:0,他引:4
研究了 RTM专用双马来酰亚胺树脂体系的流变特性,并根据树脂不同温度下反应机理的不同,建立其分段粘度模型,粘度模拟结果与实验结果具有良好的一致性。所建立的粘度模型,可有效预测和模拟该树脂体系在不同工艺条件下的粘度行为,揭示了树脂体系的优化工艺参数和低粘度平台工艺窗口,为合理拟订RTM工艺参数和保证产品质量提供了必要的科学依据 相似文献
6.
黏度是热固性树脂基体加工成型中主要的流变学参数。采用锥板旋转黏度计分别检测树脂体系在动态和稳态下的黏度-温度曲线和黏度-时间曲线,并根据优化改进的六参数双Arrhenius方程研究基于松香酸酐的生物质树脂体系的流变特性,分别由黏度相对方程的指数形式和对数形式拟合获得反应速率常数K和指前因数A,建立两种黏度模型。由对数形式拟合获得的黏度模型与实验测试值的吻合程度要优于用指数型关系式获得的黏度模型。流变模型揭示了生物质树脂体系在不同工艺条件(T,t)下的黏度变化规律,为复合材料制造过程中工艺参数的优化提供必要的科学依据。 相似文献
7.
研究了JF-45环氧树脂/氰酸酯共聚物的流变特性,并根据双阿累尼乌斯方程建立了JF-45环氧树脂/氰酸酯共聚物的化学流变模型,并对共聚物的黏度进行了预测。结果表明:在80~160℃,共聚树脂体系的相对黏度特性符合双阿累尼乌斯黏度方程;在低于160℃时反应迟缓,初始黏度较高;随着温度升高,树脂黏度降低,随时间延长黏度增加,在170℃附近黏度急剧上升;由DSC曲线和流变模型确定了共聚树脂体系的固化工艺。 相似文献
8.
王伟%曾竟成%王成忠%郭晓东 《宇航材料工艺》2006,36(Z1):42-45
研究了一种低黏度耐高温环氧树脂体系的黏温特性及固化反应动力学,考察了该树脂体系的浇注体及其碳纤维复合材料的力学性能,通过热机械分析(DMTA)研究了树脂浇注体及其复合材料的动态热机械性能.结果表明,该树脂体系在室温下黏度为0.3 Pa·s,50℃下适用期在10 h以上,130℃下可以快速固化反应,适合于RTM等快速成型工艺,Tg达到220℃以上,其碳纤维复合材料具有优良的耐高温性能. 相似文献
9.
复合材料热压成型过程环氧树脂流变特性研究 总被引:4,自引:0,他引:4
针对复合材料热压成型过程的工艺特点,以环氧618/2E4MZ及环氧618/DDS体系为研究对象,通过测试DSC曲线、η T曲线、η γ曲线及计算不同升温速率下的流动活化能,得到温度、升温速率、剪切速率对体系黏度的影响规律。在大量实验研究基础上,利用具有可操作性的固化工艺参数(dT/dt)表征了阿累尼乌斯方程中的流动活化能、指前因子及幂律方程中的黏度系数,确定了两种树脂体系黏度平台区、下降区的黏度方程。当树脂体系一定时,所建立的黏度方程描述了树脂黏度下降区及黏度平台区的黏度变化规律,为复合材料热压成型树脂流变过程的模拟研究提供了参考依据。 相似文献
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:2,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
17.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
18.
19.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
20.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献