TerraSAR-X active radar ground calibrator system

In April 2006, the TerraSAR-X satellite was launched. This paper describes the development of a novel and highly integrated, digitally-controlled active SAR system calibrator (DARC). It consists of both an active transponder path for absolute radiometric calibration and a calibrated receiver chain for antenna pattern evaluation of the satellite antenna. A total of 16 active transponder and receiver systems and 17 receiver-only systems will be fabricated for a calibration campaign in 2006.     

利用旋转双天线载波相位双差的欺骗干扰检测技术

有效的欺骗干扰检测是防止卫星导航接收机被欺骗干扰攻击的前提。提出了一种基于旋转双天线载波相位双差的卫星导航接收机欺骗干扰检测技术,在对接收机双天线匀速旋转时输出载波相位测量值进行载波相位双差处理后,利用广义似然比检验实现了对单一发射天线输出欺骗干扰信号的检测。进一步分析了旋转半径和数据长度对检测性能的影响,并与旋转单天线和天线阵载波相位双差欺骗干扰检测方法的性能进行了对比。最后,通过蒙特卡罗方法进行了仿真验证,结果表明了该检测方法和检测性能分析的正确性。     

Spaceborne GPS receiver antenna phase center offset and variation estimation for the Shiyan 3 satellite

In determining the orbits of low Earth orbit (LEO) satellites using spaceborne GPS, the errors caused by receiver antenna phase center offset (PCO) and phase center variations (PCVs) are gradually becoming a major limiting factor for continued improvements to accuracy. Shiyan 3, a small satellite mission for space technology experimentation and climate exploration, was developed by China and launched on November 5, 2008. The dual-frequency GPS receiver payload delivers 1 Hz data and provides the basis for precise orbit determination within the range of a few centime-ters. The antenna PCO and PCV error characteristics and the principles influencing orbit determi-nation are analyzed. The feasibility of PCO and PCV estimation and compensation in different directions is demonstrated through simulation and in-flight tests. The values of receiver antenna PCO and PCVs for Gravity Recovery and Climate Experiment (GRACE) and Shiyan 3 satellites are estimated from one month of data. A large and stable antenna PCO error, reaching up to 10.34 cm in the z-direction, is found with the Shiyan 3 satellite. The PCVs on the Shiyan 3 satellite are estimated and reach up to 3.0 cm, which is slightly larger than that of GRACE satellites. Orbit validation clearly improved with independent k-band ranging (KBR) and satellite laser ranging (SLR) measurements. For GRACE satellites, the average root mean square (RMS) of KBR resid-uals improved from 1.01 cm to 0.88 cm. For the Shiyan 3 satellite, the average RMS of SLR resid-uals improved from 4.95 cm to 4.06 cm.     

Integer ambiguity resolution in GPS for spinning spacecrafts

A procedure to compute the integer ambiguity problem when a GPS receiver is used in a multiple antenna configuration attached to a rotating spacecraft is presented. The method is applied to a simulation of an experimental satellite which uses the GPS receiver for attitude determination     

柔性天线面对漂浮基星载天线扰动分析及抑制

 为了研究柔性天线面弹性变形对漂浮基星载天线的扰动,采用固定界面模态综合法和Lagrange方法,通过轴末端与天线面交界面的协调关系,推导了大范围运动的星载天线刚柔耦合动力学模型,其所建立的动力学模型计算效率高并具有足够的精度。分析了柔性天线面弹性变形对星载天线的扰动,利用PD+振动力反馈控制抑制系统振动,并基于Lyapunov方法证明了控制系统的渐近稳定性。仿真结果表明：天线工作过程激起了柔性天线面弹性振动,进而引起星载天线的抖动,严重影响了星载天线的指向精度;利用其控制策略能快速抑制系统振动。结论对天线指向精度的分析与控制具有重要的理论价值及工程实际意义。     

Array antennas for DGPS

Multipath interference limits the speed and accuracy of determining position by “differential” GPS techniques. A geodetic surveyor, for example, requires multipath interference rejection of about 36+20 log₁₀ sin ϵ dB, where ϵ is the elevation angle of the satellite being observed. Signal processing in a GPS receiver cannot satisfy this requirement. A receiving antenna is required that can sufficiently reject signals arriving from below the horizon. Available antennas have inadequate rejection, and brute-force methods of improving them, by enlarging their ground-planes, are impractical. A compact, ground-planeless, dual-band, GPS antenna with improved multipath rejection has been designed and field-tested. This antenna resembles a vertical post rather than a horizontal platter; within its 0.1-m diameter, 0.4-m tall radome is a vertical array of turnstile elements. In field tests, a three-element array antenna rejected multipath better than a 0.5-m diameter ground-plane antenna by an average of 5 dB. A five-element array antenna appears superior to a 0.9-m diameter ground-plane antenna     

基于气压高度辅助的机载自主完好性监测算法

卫星接收机自主完好性监测是指根据用户接收机的多余观测值监测用户定位结果的完好性,其目的是在导航过程中检测出发生故障的卫星,并保障导航定位精度。针对卫星接收机自主完好性监测算法可用性不足的问题,结合机载实际导航系统配置,提出了一种基于气压高度表辅助的机载自主完好性监测算法。综合利用卫星导航系统及气压高度表观测信息,建立联合系统的观测模型,推导了基于多解分离的完好性监测及保护级别计算方法。仿真结果表明,相比于传统的接收机自主完好性监测算法,该算法在可见星为5颗时仍能识别故障卫星。该算法具有更好的故障检测能力及可用性,能有效提高卫星导航系统的完好性监测性能,从而保证卫星导航系统的精度和可靠性。     

基于分布式地面站天线的空间功率合成

卫星导航系统(GNSS)地面站天线对卫星进行上行注入时,信号到达卫星时较弱,容易受到干扰,故地面站注入天线需同时具备平时多目标注入和干扰时单目标功率增强的能力。利用卫星导航系统中地面站之间能够实现精密时间同步的特点,提出了一种基于分布式卫星导航地面站抛物面天线的空间功率合成方法,使用相位预补偿实现分布式天线阵到达目标卫星信号的相位粗同步;分析了相位误差、辐射功率误差对空间功率合成效率的影响,得到了阵元初始相位标定精度与相对定位精度的约束关系;并对合成信号的抗干扰能力和信号质量进行了研究。理论和仿真结果表明,当相位精度因子小于0.2时,4个等辐射功率天线在10°仰角以上波束扫描范围内的功率合成效率均在75%以上,且可以通过控制初始相位标定精度与相对定位精度实现更高的合成效率;而在合成效率要求75%以上时,天线辐射功率误差对合成效率的影响基本可以忽略。采用分布式波束扫描天线能够对地面站上行注入进行功率增强,可实现注入波束和功率的灵活配置,有效解决制约机动式和小型化地面站功率提升的瓶颈问题。     

基于载噪比同步变化的北斗欺骗检测方法

欺骗干扰已经成为北斗卫星导航系统安全性的一个严重威胁。针对北斗系统面临的欺骗干扰问题,建立二元假设检验模型。由于施加单一天线发射的欺骗干扰后,当前观测频点下各高俯仰角可见星的载噪比值会产生相同的变化趋势,所以基于此变化规律提出了一种利用K-means聚类算法进行分析的北斗卫星信号欺骗干扰检测方法,并给出了施加欺骗载噪比变化域的定义。最后通过在外场搭建实验环境,对实采数据进行了实验验证。实验结果表明,本方法对于欺骗功率优势≥6 dBm的大功率优势欺骗信号的检测概率可以达到95%以上,为提高接收机抗干扰能力提供了有益参考。     

K-Band Tracking System for Domestic Satellite Communication System

System design and operational results of a tracking system for a K-band Earth station antenna with a diameter of 11.5 m are discussed. Monopulse tracking technique using higher order waveguide modes is utilized. An investigation was conducted to clarify the rainfall effect and the effect of oscillator phase noise on the tracking receiver. An autotrack system is to be manufactured on the basis of these studies. Experiments were performed using the medium capacity communications satellite. No cross coupling was seen in the pull-in patterns. Sufficiently good results were obtained in tracking accuracy: less than 0.005° (peak value) under normal conditions, and less than 0.01° under an average wind velocity of more than 20 m/s.     

A (design-oriented) reliability model for active phased arrays insatellite communication systems

This paper proposes a modeling approach to relate the power section reliability of satellite payloads to the on-board antenna complexity. The aim of the model is to support the development of design tools for satellite systems adopting active phased arrays. The achieved results are rendered parametric with respect to a key system requirement, the effective isotropic radiated power, due to its direct impact on transmitter configuration and technological features as well as on the critical compromise between transmitter and antenna specifications     

宽波束赋形天线星地测试技术分析与改进

为满足风云三号 G星长寿命、高可靠、业务化的工作要求,星上数传天线采用通信性能好、覆盖率高的宽波束赋形设计。但宽波束赋形天线测试技术相对复杂,对测试质量有潜在影响。文章重点阐述了风云三号 G星数传天线设计方案的必要性,建立星地链路余量分析,对星载数传天线的仿真和试验结果比对进行分析,验证了天线方向图测试结果的有效性,并对星载天线和地面系统的测试技术提出改进,提高了测试结果的准确性和完整性。相应技术的改进可以为平台方案相近的空间辐射测量基准卫星平台系统综合试验验证技术提供支撑。     

浅论无人机机载卫通天线尺寸与数字信号传输带宽关系

卫星通信是无人机中继通信的重要手段。本文对无人机卫星通信链路中飞机总体设计关注的机载卫通天线尺寸选择问题进行了较详细的计算、探讨。     

机载卫星通信天线引导概率分析

针对某机载Ka频段卫星通信天线的使用环境,论述其天线角跟踪系统在捷联航姿设备引导下,天线主波束指向卫星目标位置的概率,分析影响天线角跟踪系统引导概率的主要因素,通过消减系统中大误差源保证了天线引导概率,通过扩展主波束指向空域提高了目标落入概率。计算数据和试验验证表明,给出的分析方法可行,设计策略有效。     

Multicomponent receiver architectures for GPS interference suppression

The global positioning system (GPS) is a one-way satellite-based navigation system employing spread-spectrum techniques that is widely used for commercial and military applications. Although the very low signal-to-noise ratio (SNR) is handled by the large spreading gain, GPS is susceptible to high-power interference signals and various types of jammers. We propose multicomponent receiver architectures for GPS interference suppression. A conventional antenna system is first considered which utilizes a minimum-variance distortionless-response (MVDR) beam former and assumes that the GPS signal angle of arrival (AOA) and the antenna model are known at the receiver. However, this receiver is sensitive to AOA estimation errors and can have a high computational complexity. This sensitivity problem is eliminated by a multicomponent system based on a multistage matched filter (MF). Since this MF receiver also has a high computational complexity because the jammer AOAs must be estimated, we introduce a blind interference canceler based on the constant modulus (CM) array that is insensitive to AOA estimation errors and has a low computational complexity. Computer simulations are provided to illustrate the performance of the various systems for interference suppression in example signal scenarios.     

Bandwidth maximization for satellite laser communication

Free space optical communication between satellites networked together can make possible high speed communication between different places on Earth. The basic free space optical communication network includes at least two satellites. In order to communicate between them, the transmitter satellite must track the beacon of the receiver satellite and point the information optical beam in its direction. The pointing systems for laser satellite communication suffer during tracking from vibration due to electronic noise, background radiation from interstellar objects such as Sun, Moon, Earth, and Stars in the tracking field of view, and mechanical impact from satellite internal and external sources. Due to vibrations the receiver receives less power. This effect limits the system bandwidth for given bit error rate (BER). In this research we derive an algorithm to maximize the communication system bandwidth using the transmitter telescope gain as a free variable based on the vibration statistics model and the system parameters. Our model makes it possible to adapt the bandwidth and transmitter gain to change of vibration amplitude. We also present an example of a practical satellite network which includes a direct detection receiver with an optical amplifier. A bandwidth improvement of three orders of magnitude is achieved in this example for certain conditions, as compared with an unoptimized system     

Experiments on aeronautical satellite communications using ETS-Vsatellite

The world's first aeronautical satellite communication experiments, conducted at L-band frequencies using a commercial aircraft, are described. An airborne antenna with electronically steerable beam and communication equipment was installed in a B-747F freighter flying over transoceanic flight routes. The satellite used in these experiments is the Engineering Test Satellite-Five (ETS-V). During the test period, various experiments, such as antenna pattern measurements, transmission performances, and voice quality evaluation were conducted. As the airborne antenna is the key component for the aeronautical satellite communication system, emphasis has been placed on antenna characteristics. Its performance is found to be closely related to the fading characteristics in low-elevation areas and to transmission error performance     

基于通用无线电外设的北斗信号仿真系统

研究了基于通用软件无线电外设(USRP)的北斗信号仿真系统。给出了北斗卫星电文的生成方式,使用Matlab读取星历信息并定义编码产生北斗卫星信号,并利用USRP实现北斗卫星电文的调制发射,利用接收机对该信号进行捕获接收,并对信号附加的多普勒频移进行仿真。最后通过接收机对仿真系统产生的信号进行接收验证。通过此仿真系统可更直观地研究北斗卫星信号,对研究北斗卫星导航系统具有一定的参考意义。     

基于惯性辅助的北斗接收机完好性监测方法研究

针对传统卫星导航接收机在卫星数小于5颗及卫星星座构型不佳的情况下无法实现卫星故障识别与隔离的问题,结合卫星导航接收机在弹上的实际应用情况,利用惯导的辅助数据设计了一种基于多级Kalman滤波的北斗接收机完好性监测方案,给出了卫星导航接收机的RAIM滤波器结构与故障检测和隔离方法,并对其可用性进行了推导.该方案经过仿真分...     

Zenith Pass Problem of Inter-satellite Linkage Antenna Based on Program Guidance Method

While adopting an elevation-over-azimuth architecture by an inter-satellite linkage antenna of a user satellite, a zenith pass problem always occurs when the antenna is tracing the tracking and data relay satellite （TDRS）. This paper deals with this problem by way of, firstly, introducing movement laws of the inter-satellite linkage to predict the movement of the user satellite antenna followed by analyzing the potential pass moment and the actual one of the zenith pass in detail. A number of specific orbit altitudes for the user satellite that can remove the blindness zone are obtained. Finally, on the base of the predicted results from the movement laws of the inter-satellite linkage, the zenith pass tracing strategies for the user satellite antenna are designed under the program guidance using a trajectory preprocessor. Simulations have confirmed the reasonability and feasibility of the strategies in dealing with the zenith pass problem.