基于用户端控制中的DDoS防范模型的研究

分布式拒绝服务攻击（DDoS）在Internet中正变得日益普遍，而且造成的危害也越来越大，但目前还没有一种有效的方法来对付这种攻击。本文在分析上Internet结构和现有的安全防汇方法如“防火墙”的基础上，提出一种基于用户端控制的防范策略，通过加强“防火墙”对内控制，从而有效抑制DDoS攻击。最后，讨论了这种模型的有效性。     

网络环境中安全防御措施的研究

随着网络带宽增加和网络应用的日益丰富,网络受到频繁的攻击,这种攻击采用了结合病毒、蠕虫、后门等多种方式,本文详细分析了蠕虫病毒及木马、黑客对网络的侵入和威胁,提出了安全防御措施,并阐述了利用Windows2003提供的防火墙为网络构筑安全防线的方法,Internet连接防火墙可以有效地栏截对Windows2003服务器的非法入侵,防止非法远程主机对服务器的扫描,提高Windows2003服务器的安全性,如果在用Windows2003构造的虚拟路由器上启用此防火墙功能,能够对整个内部网络起到很好的保护作用.     

基于Bayes分类器的DoS／DDoS攻击防御技术

提出了一种基于贝叶斯分类算法的分布式拒绝服务攻击防御技术。利用贝叶斯分类算法来计算数据包的分值特征,按照分值表对数据包进行评分并映射成危险等级。然后对危险等级进行评估,根据不同危险等级对网络流量进行过滤。基于该防御技术,设计并实现了防御系统。通过实验分析,该系统在DoS／DDoS攻击发生时能有效区分正常流量与异常流量,从而实现对DoS／DDoS攻击进行实时防御。     

防火墙的安全机制研究

防火墙安全机制是Internet推广和应用关键技术之一.本文通过对防火墙实现技术的分析,论述了防火墙的安全机制,描述防火墙实现的典型结构,以及采用的安全保护实现方法,并对防火墙的安全策略和设计要求进行了深入的探索.     

基于轨迹成型的攻击角度与时间控制

假定所成型的导弹飞行轨迹由圆弧段和直线段构成,直线段经过目标点且满足导弹末端攻击角度的要求,圆弧段起始于导弹初始位置且与直线段相切于待定的点,该点由指定的导弹攻击时间通过迭代算法得到。给出了可行的攻击时间范围。在轨迹成型的基础上,提出一种新的虚拟目标轨迹跟踪控制方法：在圆弧段提出一种前馈加反馈的复合控制方案,在直线段提出一种带角度控制的比例导引方案。该方法是一种几何方法,易于工程实施。仿真结果表明,该方法可以有效地同时对攻击角度与攻击时间进行控制。     

基于虚拟领弹的攻击时间和攻击角度控制

构造一枚虚拟领弹按指定的攻击时间和攻击角度以直线飞向目标。实际导弹通过机动以"等待"虚拟领弹的到来,导弹与虚拟领弹相遇后随其一起飞向目标,从而实现导弹的攻击时间和攻击角度控制。对于这种导弹对虚拟领弹的轨迹跟踪问题,建立了控制设计模型并采用了分阶段控制设计方法。仿真结果验证了该方法的有效性。     

网络防火墙系统的实施方案

介绍一种防火墙的有效实施方案。该方案是采用C和JAVA两种程序设计语言来实现的，能够有效的对进出网络的数据进行监听和控制。     

防火墙技术剖析与启示

针对Internet面临的安全问题,阐述了设置防火墙的目的和作用,介绍了防火墙技术的基本概念和体系结构,讨论了实现防火墙的主要技术手段:数据包过滤、应用级网关和代理服务,并比较了这些技术各自的优缺点。在此基础上总结得出了关于防火墙正确配置、维护以及测试验证的几点重要启示,最后分析了传统防火墙的局限性,指出新一代防火墙应具有的特性。     

“螳螂”和“苹果酒”——BAE系统公司研制的大型长航时侦察无人机

在今年范保罗航展上BAE系统公司展出了一种名为“螳螂”的长航时情报收集、监视、侦察（ISR）及攻击无人机的全尺寸模型,引起了各国参观者的极大兴趣,这种无人机瞄准的是英国国防部计划从美国采购“捕食者”B／“收割者”无人机的替代型,它也将成为英国国防部“苹果酒”计划中ISTAR模块的一个候选者。     

基于动态时间阈值的报警聚合方法研究

针对网络入侵检测中持续性攻击引发的多个报警事件时间间隔变化的问题,引入时间间隔变异系数描述报警的时间波动特征;通过将报警数据属性分为时间约束属性和相似度约束属性,提出了一种利用动态时间阈值约束的相似报警数据聚合方法。实验结果表明,这种方法能有效减少持续性攻击触发的冗余报警。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.