进气道旋流的模拟及试飞中的测量与评价

为深入研究旋流以全面评价进气道/发动机相容性,研制了一套可调叶片转折角、叶片高度、叶片数的叶片式旋流发生器.通过数值模拟、风洞试验逐步验证了叶片式旋流发生器的有效性,分析了各种可调参数对旋流发生结果的影响.提出了飞行试验中可行的旋流评价指标以及测量方案,并应用于风洞试验以进行验证.数值及试验结果表明:①所设计的旋流发生器可产生整体涡强度达28°的旋流;②叶片数、叶片攻角对旋流发生效果的影响最为显著;③通过不同的叶片布局方式可模拟出各种典型的旋流结构.      

低速来流大攻角侧滑角状态下尖脊进气道气动特性试验研究

在低速来流状态下试验研究了大攻角(α=0°～45°)和侧滑角(β=-15°～15°)对Caret进气道气动性能的影响。给出了在各攻角下进气道性能参数随侧滑角变化的特点及典型状态下进气道出口总压恢复系数分布图谱,分析了出口总压分布图谱与进气口流动之间的关系。试验表明:在低速来流状态(Ma≈0.1)下,随着攻角的增加(α从0°增加到45°),进气道总压恢复系数下降较小,总压畸变指数几乎不变,这有利于飞机的大攻角机动飞行。      

圆锥高超声速湍流边界层转捩试验研究

主要介绍了一种用于高超声速湍流边界层表面参数测量的试验方法,利用边界层的表面热流值,作为判断边界层转捩与否的依据,开展边界层攻角效应转捩特性试验研究.试验在我院FD-20炮风洞中进行,马赫数为6,试验模型是半锥度5°的圆锥模型.开展了对于圆锥模型,头部半径对转捩位置的影响,小攻角情况下对圆锥模型转捩位置的影响,并且获得了在2°和3°攻角情况下圆锥模型的攻角效应转捩全局曲线.试验结果证实了,在小攻角下,随着攻角的增加,边界层迎风面转捩位置向后移动,背风面转捩位置向前移动.     

高速大攻角Re数效应试验与分析

采用两个尺度不同的某战斗机模型,在2.4m高速风洞中进行了大攻角Re数效应试验研究。试验攻角范围为0°~70°,基于前机身端部当量直径的ReD=0.42×106~2.27×106。试验结果表明,Re数对大攻角试验数据影响明显;表面微几何效应、M数同样对大攻角气动特性也有一定影响;模型头部贴“八”字形粗糙带可以减弱Re数的影响,却不能获得高Re数下的试验结果。     

低速条件下压气机静叶栅中弯叶片对变攻角性能影响的数值分析

使用数值计算的方法对某型压气级静叶栅的直叶片与弯叶片变攻角特性进行了对比研究,结果发现弯叶片对正攻角下的流场特性有明显的影响。由于端区扩压因子的减小和近端区吸力面一侧的密流的增加,所以弯叶片能够消除或推迟在大正攻角下近吸力面角区分离的产生。弯叶片也因此可以扩大叶栅稳定工况范围,分析结果表明在某一弯角(20°)时,达到最大,临界攻角为16°。      

大涵道比涡扇发动机TPS短舱低速气动特性分析

为了评估民机低速带动力试验时进排气效应的影响,选取大涵道比发动机涡轮动力模拟器(TPS)短舱和真实发动机短舱作为研究对象,采用数值模拟方法对其起飞、进近状态的低速气动特性进行对比分析。结果表明:由于TPS流量低于真实发动机需求,其唇口、外罩流场特征和真实发动机短舱有所不同,阻力特性也有差别;在进气道处于亚临界状态时,TPS短舱阻力系数比真实短舱大了约1.7个阻力单位,又由于唇口当地气流攻角更大,使得TPS短舱失速攻角相对降低了约1.0°;当进气道工作于超临界状态时,TPS短舱虽然也可以反映真实短舱的流动特性,但由于捕获流管收缩情况和气流驻点随攻角的变化,使得在0°~20°攻角时TPS短舱的阻力系数高于真实短舱,而在20°~30°攻角时其阻力系数略低,差量最大约为1.8个阻力单位。对于研究的大涵道比发动机,未经唇口及外罩修正的TPS短舱其低速气动特性基本可以反映真实进排气效应的影响,但在气动特性分析中可以考虑进一步修正进气效应的影响。     

静子叶栅安装角异常非定常流场数值研究

为了研究静子叶栅安装角异常对叶栅通道流场的影响,利用商业软件NUMECA对二维叶栅某个叶片安装角增加5°不同攻角进行非定常流场数值模拟,得到了因安装角异常导致叶栅通道堵塞时对叶栅通道内的流场结构及叶片载荷的影响。结果表明,安装角调节5°时,在正攻角下,随着攻角的增大叶栅通道内流动不断恶化,吸力面出现大面积的附面层分离;负攻角时,气流比较平稳,但是漩涡脱落频率高达3500Hz。分析发现,安装角异常时攻角对漩涡尺度和脱落频率影响较大,其中叶片动态气动力脉动量迅速增大,可能是导致发动机叶片疲劳破坏的原因之一。     

进气道旋流发生器的设计与数值模拟

为深入研究旋流以全面评价进气道/发动机相容性,设计了一套可调叶片转折角、叶片高度、叶片数的叶片式旋流发生器.利用CFD数值模拟技术,对旋流发生器进行了各种组合的流场计算,分析了可调参数对旋流发生结果的影响.结果表明,所设计的旋流发生器能够产生整体涡强度达8°～22°的旋流,叶片数对旋流整体涡强度的影响最为显著.     

前机身/进气道攻角特性的数值与试验研究

为研究前机身/进气道内外流场的攻角特性,对其一体化模型进行综合求解。将数值计算结果与试验数据进行对比以验证数值方法。分析了不同攻角下前机身对进气道入口气流的影响以及进气道内部流动情况,同时分析了攻角对进气道总压恢复系数和出口总压畸变指数的影响。结果表明:进气道位于机身下侧的布局能在大攻角下降低进气道入口的迎角和马赫数,有效提高飞行极限;在超声来流下,进气道在很宽泛的攻角范围内总压恢复系数都能达到0.94左右,在9°到18°攻角范围内具有较低水平的总压畸变,在此攻角范围之外,总压畸变对攻角的变化很敏感。     

覆冰导线气动力特性风洞试验研究

针对新月形和D形两种典型断面的特(超)高压大截面厚覆冰导线进行了气动力系数风洞测试,获取了0°～180°以5°攻角为间隔各攻角下的气动三分力系数,用均匀流和均匀湍流两种风场研究湍流对覆冰导线气动力特性的影响,根据Den Hartog理论分别计算了两种断面覆冰导线可能发生舞动的风攻角范围。结合以往试验结果,归纳了两类覆冰冰型气动力特征。试验结果表明:新月形覆冰导线可能发生Den Hartog舞动的攻角范围为15°～30°和175°～180°,D形覆冰导线则为65°～85°及135°～150°,湍流对导线舞动气动稳定性存在影响。与以往试验结果比较表明:本试验结果能够反映大覆冰新月形和D形覆冰导线气动力特征,小覆冰新月形导线气动力特性则与本试验存在较大差异。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.