共查询到18条相似文献,搜索用时 156 毫秒
1.
高低周复合载荷对TC11钛合金疲劳性能的影响 总被引:2,自引:3,他引:2
为了解高周振动应力对TC11钛合金疲劳性能的影响,进行了TC11的低周疲劳、高周疲劳、以及高低周复合疲劳试验.试验结果表明:高低周复合循环降低了TC11钛合金的抗疲劳性能;复合循环载荷中,高周平均应力水平 σ major和应力比 R minor对高低周复合寿命有较大的影响.采用扫描电子显微镜(SEM)比较分析了不同类型载荷下的断口宏观和微观形貌特征,高低周复合疲劳断口与高周断口有较明显的区别,高低周复合载荷中的低周循环引起的较大滑移是引起疲劳寿命降低的主要原因. 相似文献
2.
对锻造TC4钛合金电子束焊接(EBW)接头进行了应力控制的高周疲劳试验和应变控制的低周疲劳试验,利用扫描电子显微镜对疲劳断口进行观察与分析,研究了疲劳裂纹的起裂机制.研究结果表明:所有的高周疲劳试样裂纹起裂位置和最后断裂位置均发生在母材区,而低周疲劳试验试样断裂位置表现出不确定性,在焊缝区和母材区均可导致裂纹起裂.高周疲劳载荷下,裂纹起源于表面滑移;低周疲劳时,裂纹可能在接头母材区的表面起裂,也可能在接头焊缝的内部缺陷处起裂,裂纹起裂模式取决于载荷大小. 相似文献
3.
涡轮叶片复合疲劳特性曲线及其规律的试验 总被引:3,自引:4,他引:3
为了解高周振动载荷对于涡轮叶片高温疲劳性能的影响,对某型涡轮叶片进行高低周复合疲劳试验.试验结果表明,在低周载荷基础上叠加高频振动载荷,显著缩短了叶片的疲劳寿命;复合疲劳的分散性很大,且不存在疲劳极限,当叶片高周循环次数超过107时,继续试验叶片仍会发生断裂;在双对数坐标下,叶片的振动应力与其高周循环寿命成线性关系,即复合疲劳特性曲线(应力-寿命曲线、概率-应力-寿命曲线)服从双对数线性规律,进一步研究发现该规律对于高温合金材料的复合疲劳特性曲线具有普遍性. 相似文献
4.
5.
6.
TC11材料高低周疲劳裂纹萌生与扩展特性研究 总被引:2,自引:0,他引:2
通过对航空发动机叶片用TC11材料在高低周复合载荷下进行裂纹扩展试验,研究了TC11材料高低周复合疲劳裂纹扩展规律,得到了高低周载荷条件下的裂纹稳态扩展曲线及断口特征。其结果可对风扇/压气机叶片抗高低周复合载荷下的裂纹扩展能力进行分析和评估,为下一代先进航空发动机设计提供技术支撑。 相似文献
7.
8.
9.
基于整机试车的涡轮叶片高低循环复合疲劳试验技术 总被引:3,自引:3,他引:0
针对航空发动机涡轮叶片同时承受高循环载荷和低循环载荷的特征,以小推力涡喷发动机为研究对象,搭建了基于引电器的涡轮叶片动应力测量系统,利用数值模拟和试验测试结合的方法,实现了高度为30mm的涡轮叶片在40000r/min转速、950℃环境温度条件下的动应力测量,并以此为基础发展了整机高低循环复合疲劳试验方法,开展了高压涡轮叶片高低复合疲劳整机试验。研究结果表明,该型发动机转速在34920r/min时,叶片高循环振动应力达到112.7MPa,带来了涡轮叶片的高循环疲劳损伤且是引起涡轮叶片产生裂纹的主要因素,低循环疲劳载荷是导致裂纹扩展的主要因素,两者综合作用会显著影响涡轮叶片寿命。 相似文献
10.
研究了IN718合金在360℃、550℃和650℃下的低周疲劳行为及疲劳裂纹扩展速率da/dN,包括循环应力-应变行为、Massing效应、低周疲劳寿命的能量表达以及疲劳裂纹扩展速率,并讨论了保持时间对da/dN的影响。实验结果表明,该合金在各种温度下表现出循环软化,在本文所试温度下具有Massing特性,其塑性应变能与疲劳寿命在双对数坐标中呈现出很好的线性关系,其da/dN随温度的升高而增大,在650℃下保持时间对da/dN的影响很明显,而550℃时则很轻微。 相似文献
11.
试验研究了预先经历一定次数的低周疲劳(low cycle fatigue, LCF)对TA11合金高周疲劳(high cycle fatigue,HCF)强度的影响.考虑了LCF试验中循环最大应力、应力比和寿命比例等主要参数,根据步进法,利用旋转弯曲疲劳试验,研究了LCF预损伤对标准试件HCF强度的影响规律.结果表明:当循环最大应力为900MPa时,LCF载荷中靠前的循环产生的塑性应变大,因此加载较少的LCF预损伤也会降低该合金HCF强度;不同应力比的LCF预损伤都会降低HCF强度;当LCF预损伤的最大应力远小于材料的屈服强度时,LCF预损伤对HCF强度的影响较小,而当LCF预损伤的最大应力接近或大于材料的屈服强度时,则必须考虑LCF预损伤对TA11合金HCF强度的影响. 相似文献
12.
Based on experiments of low cycle fatigue for 5083-H112 aluminum alloy, two energy-based predictive models have been introduced to predict the fatigue crack growth behaviors of traditional Compact Tension (CT) and small-sized C-shaped Inside Edge-notched Tension (CIET) specimens with different thicknesses and load ratios. Different values of the effective stress ratio U are employed in the theoretical fatigue crack growth models to correct the effect of crack closure. Results indicate that the two predictive models show different capacities of predicting the fatigue crack growth behaviors of CIET and CT specimens with different thicknesses and load ratios. The accuracy of predicted results of the two models is strongly affected by the method for determination of the effective stress ratio U. Finally, the energy-based Shi&Cai model with crack closure correction by means of Newman’s method is highly recommended in prediction of fatigue crack growth of CIET specimens via low cycle fatigue properties. 相似文献
13.
A new method to predict fatigue crack growth rate of materials based on average cyclic plasticity strain damage accumulation 总被引:3,自引:3,他引:0
By introducing a fatigue blunting factor, the cyclic elasto-plastic Hutchinson-Rice-Rosengren (HRR) field near the crack tip under the cyclic loading is modified. And, an average damage per loading-cycle in the cyclic plastic deformation region is defined due to Manson-Coffin law. Then, according to the linear damage accumulation theory-Miner law, a new model for predicting the fatigue crack growth (FCG) of the opening mode crack based on the low cycle fatigue (LCF) damage is set up. The step length of crack propagation is assumed to be the size of cyclic plastic zone. It is clear that every parameter of the new model has clearly physical meaning which does not need any human debugging. Based on the LCF test data, the FCG predictions given by the new model are consistent with the FCG test results of Cr2Ni2MoV and X12CrMoWVNbN 10-1-1. What’s more, referring to the relative researches, the good predictability of the new model is also proved on six kinds of materials. 相似文献
14.
由于材料、尺寸以及载荷等的分散性,涡轮盘疲劳寿命存在较大的分散性。在充分考虑材料加卸载应力、应变及应力比对疲劳寿命影响的基础上,提出了一种适用于中低周疲劳的塑性应变能概率寿命模型。该模型在考虑材料、尺寸和载荷等导致寿命分散的因素的基础上,重点考虑了循环应力应变曲线的分散性,结合根据应力比的二次插值,获得了插值范围内任意应力比下的塑性应变能损伤参量与疲劳寿命的关系。运用所提概率寿命模型结合响应面法与蒙特卡洛法对某涡轮盘螺栓孔模拟试件进行了概率寿命分析。结果显示,模拟试件的计算结果与试验结果的中位寿命仅相差022%,寿命分散系数相差581%,说明本概率寿命模型概率寿命预估精度高。 相似文献
15.
16.
带保载平面应变塑性诱发裂纹闭合效应 总被引:1,自引:1,他引:1
用黏塑性有限元法模拟含中心裂纹试件在等幅循环拉伸加载和保载作用下的裂纹扩展规律.试件采用涡轮盘材料Udimet720 Li(low inclusion)、恒温700℃和平面应变假设,通过逐步释放裂纹尖端节点约束来模拟裂纹扩展.计算了在应力比R=0,不同最大循环载荷、不同保载时间对平面应变下无量纲裂纹张开应力强度因子的影响.平面应变情况下,无量纲裂纹张开应力强度因子随最大载荷的变化而趋于分散,并随着裂纹的扩展,会存在先上升后下降并趋于一个稳定值的趋势;载荷相同时,保载时间的增加使裂纹张开应力强度因子增加.高温保载情况下,蠕变会影响裂纹扩展速率. 相似文献
17.
A theoretical model of semi-elliptic surface crack growth based on the low cycle strain damage accumulation near the crack tip along the cracking direction and the Newman–Raju formula is developed. The crack is regarded as a sharp notch with a small curvature radius and the process zone is assumed to be the size of cyclic plastic zone. The modified Hutchinson, Rice and Rosengren(HRR) formulations are used in the presented study. Assuming that the shape of surface crack front is controlled by two critical points: the deepest point and the surface point.The theoretical model is applied to semi-elliptic surface cracked Al 7075-T6 alloy plate under cyclic loading, and five different initial crack shapes are discussed in present study. Good agreement between experimental and theoretical results is obtained. 相似文献
18.
本文论述了近几十年来国内外关于疲劳短裂纹的一些理论模型和实验现象等;重点研究了短裂纹的"V"型扩展规律及其特有的非扩展裂纹行为;通过各种不同复杂程度的理论模型,说明了短裂纹"V"型扩展规律,并给出了非扩展裂纹的计算方法;通过试验方法,分析了物件的形式、缺口塑性区、微观结构和试验环境等因素对短裂纹的"V"型扩展规律和非扩展裂纹行为的影响。 相似文献