变循环发动机总体结构和模式转换机构研究

根据1种涡扇发动机的总体结构设计方案,围绕变循环特征的适应性进行了改进设计,给出了变循环发动机的总体结构初步方案,设计了模式转换原理及其结构实现方案;以其可调面积涵道引射器的设计为例,进行了模式转换机构运动仿真及其关键件的有限元分析,从机构运动和强度分析方面确定了该方案的可行性.     

变循环与自适应循环发动机技术发展

变循环发动机具有兼顾低速、高速飞行性能的优势;自适应循环发动机是最新颖的变循环发动机构型,具有更强的循环调节能力和任务适应性,是重要发展方向。回溯变循环发动机的发展历程,总结变循环技术进化的路径,发展针对这类难度大、高风险的技术,不能跨越技术成熟的必要环节,要明确其主要技术关键,合理安排技术路线,分散难点,充分利用已有平台资源,逐步增加变循环的复杂程度,最终实现突破。     

变循环发动机过渡态性能直接模拟方法

为了实现多变量可调的变循环发动机（VCE）过渡态性能模拟和控制规律设计,在稳态逆算法和过渡态性能隐式格式计算方法的基础上开发了变循环发动机过渡态直接模拟方法。在稳态逆算法模型中加入容积效应和转子动力学方程,实现了同时给定加速率、涡轮前温度和压缩部件工作点的条件下直接模拟计算过渡态过程中变几何参数和燃油流量的调节规律,验证了方法的精度和可行性,并将该方法用于变循环发动机转模态性能模拟和控制规律设计。计算结果表明,过渡态直接模拟方法的误差在0.58%以内,超声速巡航状态下由单外涵模态转换到双外涵模态的时间约为1 s,海平面静止状态下双外涵转单外涵的时间约为3 s,且推力、转速、涡轮前温度、喘振裕度等参数过渡平稳。该方法可简化转模态控制规律设计流程,并提高设计精度。     

3 外涵变循环发动机循环参数匹配模拟

3外涵技术能使发动机涵道比调节范围更宽,使其在所有推力范围和全包线下性能最优。分析了带核心机驱动风扇级（CDFS）的3外涵变循环发动机工作机理,利用稳态性能数值仿真程序,开展了3外涵变循环发动机循环参数匹配模拟研究,得到发动机循环参数取值范围。研究结果表明：3外涵变循环发动机工作范围更广,重点是通过改变其涵道比来实现压比的变化和发动机模态的转变,最终实现3外涵变循环发动机的优越性能。     

美国自适应发动机研究的进展与启示

为借鉴和参考美国自适应循环发动机的研究与研制经验,综述了美国变循环发动机演变至自适应发动机的3个发展阶段,重点介绍了其在多用途经济可承受的先进涡轮发动机(VAATE)研究计划下的自适应通用发动机技术(ADVENT)分计划、自适应发动机技术验证(AETD)分计划、自适应发动机过渡(AETP)分计划和空中优势自适应推进技术(ADAPT)分计划的开发与验证情况。分析总结出美国自适应发动机具有以下特点:技术先进且应用前景广泛,代表未来发展方向;变循环与自适应循环技术均不成熟,还需深入验证;技术研究采用竞争策略实施。     

航空发动机组态建模技术研究

基于组态的方法设计了航空发动机部件模型库、仿真实时数据库以及前台组态系统和后台运行管理系统,构建航空发动机组态建模平台,并在此平台上实现了多种结构发动机模型的稳态仿真和瞬态仿真,其结果达到了一定精度,验证了航空发动机组态建模技术的可用性.      

基于UG和ADAMS的调节机构虚拟样机动力学仿真

在航空发动机压气机可调静叶调节机构设计中运用虚拟样机技术,可以大大丰富设计手段,提高设计效率.本文在UG环境下进行三级联调机构三维实体模型的建造并将数字模型导入到ADAMS环境下对其进行动力学仿真,验证了机构设计的正确性.     

一种伞式可折叠柔性变胞机构的设计分析研究

 柔性变胞机构是一种依靠柔性构件变形实现构态变化的机构,利用柔性机构的某些特性可以综合提高变胞机构的性能和效率。提出一种伞式可折叠柔性变胞机构,该机构综合了变胞机构和柔性机构两大特点。利用伪刚体模型理论对该机构进行拓扑学,运动学及稳态分析。最后,对该机构进行运动学仿真,结果表明伪刚体模型法适合于柔性变胞机构的分析与设计。     

变循环涡扇冲压组合发动机发展现状及关键技术分析

总结了国内外变循环涡扇冲压组合发动机的发展现状,对比分析了有/无能量传递构型的变循环涡扇冲压组合发动机的工作原理及优缺点。提炼了变循环涡扇冲压组合发动机的关键技术,包括总体性能仿真技术、高速宽工况风扇设计技术、加力/冲压燃烧室设计技术、热管理系统设计技术以及模态转换设计技术。基于国内需求和相关技术研究现状,给出了变循环涡扇冲压组合发动机后续重点研究方向的建议,包括发动机总体性能设计与仿真工具、发动机多设计点多学科耦合设计方法、发动机热管理系统设计与仿真建模以及关键部件的设计与试验。     

VSV调节机构阻滞力和调节精度的归因分析

基于ANCF方法和摩擦力的NURBS表达算法，构建了考虑装配间隙、尺寸公差、关键件柔性、热影响以及接触摩擦等因素的复杂VSV调节机构的刚柔耦合动力学模型，并依据部件空间分布关系和参数化表述开发了VSV调节机构的快速自动化建模流程，大大提升了建模效率。分别对VSV调节机构的单级模拟气动实验及热态联调实验状态进行了对比仿真，结果表明，所构建的VSV调节机构模型在阻滞力仿真方面具有较高的可信度，且气动力引起的摩擦力矩是造成机构阻滞力、角度调节迟滞和调节精度下降的主要原因，气动力矩对机构阻滞力和角度迟滞影响不明显，关键件柔性对阻滞力影响较小，但却是调节精度降低的内在因素。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.