Bayesian edge detector for SAR imagery using discontinuity-adaptive Markov random feld modeling

Synthetic aperture radar（SAR）image is severely affected by multiplicative speckle noise,which greatly complicates the edge detection.In this paper,by incorporating the discontinuityadaptive Markov random feld（DAMRF）and maximum a posteriori（MAP）estimation criterion into edge detection,a Bayesian edge detector for SAR imagery is accordingly developed.In the proposed detector,the DAMRF is used as the a priori distribution of the local mean reflectivity,and a maximum a posteriori estimation of it is thus obtained by maximizing the posteriori energy using gradient-descent method.Four normalized ratios constructed in different directions are computed,based on which two edge strength maps（ESMs）are formed.The fnal edge detection result is achieved by fusing the results of two thresholded ESMs.The experimental results with synthetic and real SAR images show that the proposed detector could effciently detect edges in SAR images,and achieve better performance than two popular detectors in terms of Pratt＇s fgure of merit and visual evaluation in most cases.     

Nonuniform Three-dimensional Configuration Distributed SAR Signal Reconstruction Clutter Suppression

This paper deals with the problem of clutter suppression in spaceborne distributed synthetic aperture radar (D-SAR) with nonuniform three-dimensional (3D) configuration geometry. In order to make a breakthrough of the configuration limitation of the traditional space time adaptive processing (STAP) based on uniform array and improve the inhomogeneous clutter suppression performance, this paper considers signal reconstruction technique using array interpolation to process the D-SAR signal. An array interpolation signal reconstruction method based on pitching-partition is derived then a signal reconstruction 3D-STAP clutter suppression method applied to nonuniform 3D configuration is proposed. In particular, the proposed method is compared with conventional methods and the performance analysis is carried out based on simulations. The improvement factor (IF) for clutter suppression is imported and reported as a benchmark on the clutter suppression effect.     

Gaussian process regression model incorporated with tool wear mechanism

Cutting tool condition directly affects machining quality and efficiency. In order to avoid severely worn tools used during machining process and fully release the remaining useful life in the meanwhile, a reliable evaluation method of remaining useful life of cutting tools is quite necessary.Due to the variation of cutting conditions, it is a challenge to predict remaining useful life of cutting tools by a unified model. In order to address this issue, this paper proposes a method for predictin...     

MATHEMATICAL MODEL AND DIGITAL SIMULATION OF TURBOJET ACCELERATION

The acceleration performance of a turbojet is one of its important characteristics. In terms of control system, the engine is a controlled object. The acceleration performance not only depends on the engine, but also on the controller; therefore both the engine and the controller must be combined in a control system to make research for this performance. This paper presents a mathematical model of the turbojet acceleration control system and digital simulation method. Because the engine acceleration is a large variation transient process, the models of the engine and the controller are described by nonlinear equations. The methods of solving nonlinear equations and iterative techniques of calculating acceleration control system are discussed in this paper. The calculated results, as compared with test results, show that the simulation for this system is satisfactory.     

Remaining useful life prediction based on the Wiener process for an aviation axial piston pump

An aviation hydraulic axial piston pump’s degradation from comprehensive wear is a typical gradual failure model. Accurate wear prediction is difficult as random and uncertain char-acteristics must be factored into the estimation. The internal wear status of the axial piston pump is characterized by the return oil flow based on fault mechanism analysis of the main frictional pairs in the pump. The performance degradation model is described by the Wiener process to predict the remaining useful life (RUL) of the pump. Maximum likelihood estimation (MLE) is performed by utilizing the expectation maximization (EM) algorithm to estimate the initial parameters of the Wiener process while recursive estimation is conducted utilizing the Kalman filter method to estimate the drift coefficient of the Wiener process. The RUL of the pump is then calculated accord-ing to the performance degradation model based on the Wiener process. Experimental results indi-cate that the return oil flow is a suitable characteristic for reflecting the internal wear status of the axial piston pump, and thus the Wiener process-based method may effectively predicate the RUL of the pump.     

An extended chirp scaling algorithm for spaceborne sliding spotlight synthetic aperture radar imaging

A system impulse response with low sidelobes is critical in synthetic aperture radar（SAR） images because sidelobes contribute to noise and interfere with nearby scatterers. However,the conventional tricks of sidelobe suppression are unable to be exactly applied to the case of spaceborne sliding spotlight SAR due to great azimuth shifts in both time and frequency domains. In this paper, an extended chirp scaling algorithm is presented for spaceborne sliding spotlight SAR data imaging. The proposed algorithm firstly uses the spectral analysis（SPECAN） technique to avoid the azimuth spectrum folding effect and then employs the chirp scaling（CS） algorithm to achieve data focusing, i.e., the so-called two-step approach. To suppress the sidelobe level, an efficient strategy for the azimuth spectral weighting which only involves matrix multiplications and short fast Fourier transformations（FFTs） is proposed, which is a post-process executed on the focused SAR image and particularly simple to be implemented. The SAR image processed by the proposed extended CS algorithm is very precise and perfectly phase-preserving. In the end, computer simulation results verify the analysis and confirm the validity of the proposed algorithm.     

Process-scheme-driven N C machining cell for automatic construction of aircraft structural parts

In order to enhance the NC programming efficiency and quality of aircraft structural parts （ASPs）, an intelligent NC programming pattern driven by process schemes is presented. In this pattern, the NC machining cell is the minimal organizational structure in the technological process, consisting of an operation machining volume cell, and the type and parameters of the machining operation. After the machining cell construction, the final NC program can be easily obtained in a CAD/CAM system by instantiating the machining operation for each machining cell. Accordingly, how to automatically establish the machining cells is a key issue in intelligent NC program- ming. On the basis of the NC machining craft of ASP, the paper aims to make an in-depth research on this issue. Firstly, some new terms about the residual volume and the machinable volume are defined, and then, the technological process is modeled with a process scheme. Secondly, the approach to building the machining cells is introduced, in which real-time complement machining is mainly considered to avoid interference and overcutting. Thirdly, the implementing algorithm is designed and applied to the Intelligent NC Programming System of ASP. Finally, the developed algorithm is validated through two case studies.     

Aerodynamic design optimization of nacelle/pylon position on an aircraft

The arbitrary space-shape free form deformation (FFD) method developed in this paper is based on non-uniform rational B-splines (NURBS) basis function and used for the integral parameterization of nacelle-pylon geometry. The multi-block structured grid deformation technique is established by Delaunay graph mapping method. The optimization objects of aerodynamic characteristics are evaluated by solving NavierStokes equations on the basis of multi-block structured grid. The advanced particle swarm optimization (PSO) is utilized as search algorithm, which com-bines the Kriging model as surrogate model during optimization. The optimization system is used for optimizing the nacelle location of DLR-F6 wing-body-pylon-nacelle. The results indicate that the aerodynamic interference between the parts is significantly reduced. The optimization design system established in this paper has extensive applications and engineering value.     

Nonlinear finite time attitude control of flexible spacecraft based on a novel output redefinition method

A finite time attitude controller is designed for a flexible spacecraft based on a novel output redefinition method, in this paper. To make the flexible appendages vibration suppression effective, the appendage tip-point is selected as the output. First, a novel output redefinition method is proposed to overcome the non-minimum phase property of the dynamic model. The proposed method not only makes the system model minimum phase but also improves the attitude control system performance. Conseque...