Moving scanning emitter tracking by a single observer using time of interception: Observability analysis and algorithm

The target motion analysis (TMA) for a moving scanning emitter with known fixed scan rate by a single observer using the time of interception (TOI) measurements only is investigated in this paper.By transforming the TOI of multiple scan cycles into the direction difference of arrival (DDOA) model,the observability analysis for the TMA problem is performed.Some necessary conditions for uniquely identifying the scanning emitter trajectory are obtained.This paper also proposes a weighted instrumental variable (WIV) estimator for the scanning emitter TMA,which does not require any initial solution guess and is closed-form and computationally attractive.More importantly,simulations show that the proposed algorithm can provide estimation mean square error close to the Cramer-Rao lower bound (CRLB) at moderate noise levels with significantly lower estimation bias than the conventional pseudo-linear least square (PLS) estimator.     

Infrared Systems: I. Accuracy of Angle Measurement

In this paper expressions are derived for the error in position measurement for the problem of estimating the position of an infrared target in a random background and the combined prob lem when white detector noise is also affecting the estimation. Space filters performing linear scanning, nutation, and rotation are considered. A linear scanning infrared system is then considered in greater detail. The noise on the error signal is calculated, taking into account both the estimation error, as discussed in the first part, and "false alarms" occurring in the scan area far from the target.     

The Effects of Defruiting on the ATCRBS

The defruiter that is employed in the Air Traffic Control Radar Beacon System (ATCRBS) to prefilter asynchronous replies has a complex impact on the detection, estimation and validation properties of the detection subsystem. Its positive and negative effects are quantitatively enumerated via a simulation of the beacon processing subsystem of the Automated Radar Terminal System (ARTS III). It is concluded that the disadvantages of using the present-day defruiter in the ARTS III digital processing channel outweigh the advantages when fruit rates are below several thousand per scan. As an alternative to the total elimination of the defruiter a more general class of preprocessors is defined and their input-output relationships are derived using a Markov Chain formulation. These are found to represent an improvement over the current defruiter in that the positive effects of defruiting are retained while some of the negative effects are reduced.     

One-step solution for the multistep out-of-sequence-measurement problem in tracking

In multisensor target tracking systems measurements from the same target can arrive out of sequence. Such "out-of-sequence" measurement (OOSM) arrivals can occur even in the absence of scan/frame communication time delays. The resulting problem - how to update the current state estimate with an "older" measurement - is a nonstandard estimation problem. It was solved first (suboptimally, then optimally) for the case where the OOSM lies between the two last measurements, i.e, its lag is less than a sampling interval - the 1-step-lag case. The real world has, however, OOSMs with arbitrary lag. Subsequently, the suboptimal algorithm was extended to the case of an arbitrary (multistep) lag, but the resulting algorithm required a significant amount of storage. The present work shows how the 1-step-lag algorithms can be generalized to handle an arbitrary (multistep) lag while preserving their main feature of solving the update problem without iterating. This leads only to a very small (a few percent) degradation of MSE performance. The incorporation of an OOSM into the data association process is also discussed. A realistic example with two GMTI radars is presented. The consistency of the proposed algorithm is also evaluated and it is found that its calculated covariances are reliable.     

KUPS: Knowledge-Based Ubiquitous and Persistent Sensor Networks for Threat Assessment

We propose a knowledge-based ubiquitous and persistent sensor network (KUPS) for threat assessment, in which "sensor" is a broad characterization. It refers to diverse data or information from ubiquitous and persistent sensor sources such as organic sensors and human intelligence sensors. Our KUPS for threat assessment consists of two major steps: situation awareness using fuzzy logic systems (FLSs) and threat parameter estimation using radar sensor networks (RSNs). Our FLSs combine the linguistic knowledge from different intelligent sensors, and our proposed maximum-likelihood (ML) estimation algorithm performs target radar cross section (RCS) parameter estimation. We also show that our ML estimator is unbiased and the variance of parameter estimation matches the Cramer-Rao lower bound (CRLB) if the radar pulses follow the Swerling II model. Simulations further validate our theoretical results.     

无人直升机视觉着陆中的运动状态估计算法

对无人直升机(UH)视觉着陆中基于视觉图像处理的运动状态估计问题进行了研究。介绍了视觉着陆原理,分析了运动估计、特征图像处理与着陆控制间的关系,推导并建立了UH相对着陆平台位姿估计算法、线速度与角速度估计算法。相邻两帧图像对应特征点像点位置为位姿估计算法提供数据,一帧图像特征点像点位置及其对应像点平移速度为线速度与角速度估计算法提供数据。利用UH着陆控制仿真数据模拟UH着陆运动过程中像点位置及其对应平移速度的视觉图像处理结果。仿真验证了运动状态估计算法,结果表明所提出的运动状态估计算法能有效地利用视觉图像处理结果数据估计出UH的位置、姿态、线速度和角速度。     

Model-based robust estimation and fault detection for MEMS-INS/GPS integrated navigation systems

In micro-electro-mechanical system based inertial navigation system（MEMS-INS）/global position system（GPS） integrated navigation systems, there exist unknown disturbances and abnormal measurements. In order to obtain high estimation accuracy and enhance detection sensitivity to faults in measurements, this paper deals with the problem of model-based robust estimation（RE） and fault detection（FD）. A filter gain matrix and a post-filter are designed to obtain a RE and FD algorithm with current measurements, which is different from most of the existing priori filters using measurements in one-step delay. With the designed filter gain matrix, the H-infinity norm of the transfer function from noise inputs to estimation error outputs is limited within a certain range; with the designed post-filter, the residual signal is robust to disturbances but sensitive to faults. Therefore, the algorithm can guarantee small estimation errors in the presence of disturbances and have high sensitivity to faults. The proposed method is evaluated in an integrated navigation system, and the simulation results show that it is more effective in position estimation and fault signal detection than priori RE and FD algorithms.     

Mini-UAV altitude estimation using an inertially stabilized payload

A novel method is introduced for autonomous attitude estimation of a mini unmanned aerial vehicle (UAV) carrying an inertially stabilized payload. The method is based on utilizing the outputs of rate gyros normally used to inertially stabilize the payload, and other data that is normally available from conventional aircraft-mounted sensors. A decentralized estimation algorithm is developed, which uses the aircraft/payload mathematical models to bound the estimation errors. Exploiting modern multiprocessor computer technology, the new estimation algorithm comprises two parallel extended Kalman filters (EKFs) and a data fusion algorithm. Real-time experimental tests, incorporating a payload model with real rate gyros mounted on a three-axis flight table, have validated the feasibility of the concept. The theoretical and experimental investigation demonstrates that the estimation algorithm is capable of estimating the attitude angles with an estimation error not exceeding 1 deg, at output rates of 13 Hz, thus constituting a viable substitute for the conventional vertical gyroscope     

Aerodynamic Modeling and Parameter Estimation from QAR Data of an Airplane Approaching a High-altitude Airport

Aerodynamic modeling and parameter estimation from quick accesses recorder (QAR) data is an important technical way to analyze the effects of highland weather conditions upon aerodynamic characteristics of airplane. It is also an essential content of flight accident analysis. The related techniques are developed in the present paper, including the geometric method for angle of attack and sideslip angle estimation, the extended Kalman filter associated with modified Bryson-Frazier smoother (EKF-MBF) method for aerodynamic coefficient identification, the radial basis function (RBF) neural network method for aerodynamic modeling, and the Delta method for stability/control derivative estimation. As an application example, the QAR data of a civil airplane approaching a high-altitude airport are processed and the aerodynamic coefficient and derivative estimates are obtained. The estimation results are reasonable, which shows that the developed techniques are feasible. The causes for the distribution of aerodynamic derivative estimates are analyzed. Accordingly, several measures to improve estimation accuracy are put forward.     

边界扫描技术在电子控制器测试中的应用研究

航空发动机电子控制器向更高性能和更高集成度的方向发展,使得传统测试方法难以满足需要。本文提出了通过边界扫描技术来解决电子控制器核心电路的测试问题。为了论证这一方案的可行性,设计了边界扫描测试技术验证平台,主要包括边界扫描测试适配器和被测电路。对被测电路开展了基于边界扫描的测试试验,完成了主要指令的测试。同时通过扫描链实现了对被测电路的故障注入,通过这种方法注入故障可对航空发动机电子控制器的机内测试（BIT）能力进行验证。本文探索了边界扫描测试技术在航空发动机电子控制器中的应用     

Markov随机跳变系统的传感器系统误差估计

 针对Markov随机跳变系统的系统误差估计问题,提出一种基于马尔可夫链蒙特卡罗(MCMC)和最大似然估计相结合的在线系统误差估计方法。利用最大似然估计给出系统误差等效后验概率分布函数,采用Metropolis-Hastings抽样方法从该概率分布函数中进行抽样;利用系统误差估计和状态估计互为因果的关系,采用期望极大化(EM)方法迭代估计出最优的系统误差;分别对时变和时不变系统误差场景进行仿真分析,结果表明,在考虑系统误差统计特性的同时,所提方法对解决目标运动模型难以建立情况下的系统误差估计问题具有可行性和有效性。     

A fast pulse phase estimation method for X-ray pulsar signals based on epoch folding

X-ray pulsar-based navigation (XPNAV) is an attractive method for autonomous deep-space navigation in the future. The pulse phase estimation is a key task in XPNAV and its accuracy directly determines the navigation accuracy. State-of-the-art pulse phase estimation techniques either suffer from poor estimation accuracy, or involve the maximization of generally non-convex object function, thus resulting in a large computational cost. In this paper, a fast pulse phase estimation method based on epoch folding is presented. The statistical properties of the observed profile obtained through epoch folding are developed. Based on this, we recognize the joint prob-ability distribution of the observed profile as the likelihood function and utilize a fast Fourier transform-based procedure to estimate the pulse phase. Computational complexity of the proposed estimator is analyzed as well. Experimental results show that the proposed estimator significantly outperforms the currently used cross-correlation (CC) and nonlinear least squares (NLS) estima-tors, while significantly reduces the computational complexity compared with NLS and maximum likelihood (ML) estimators.     

Real-Time Motion Desmearing of Airborne Imagery

This paper considers the real-time ?desmearing? of motion- ?smeared? imagery telemetered from an airborne platform. The specific configuration considered is the direct raster scan readout of a satellite-mounted vidicon. Three types of smearing are considered: 1) linear uniform smearing, 2) linear nonuniform smearing, and 3) nonlinear smearing. The simplest type of smearing, linear uniform, has as its desmearing or inverse filter a circulating delay line (CDL) cascaded with a differentiator. An error analysis of this filter is presented along with an experimental simulation. Linear, non-uniform smearing characterized by the operator begin{equation*}int^{t}_{t-delta(t)}I(tau){ }{dtau}end{equation*} is considered next. Two possible realizations for the inverse filter are discussed as to accuracy and practicality. Finally, an error analysis is performed for the nonlinear smearing that results from a skewing of the raster scan.     

基于相似变换的涡扇发动机智能动态推力估计方法

智能推力估计面临飞行包线大、工作状态多变带来的数据采集和处理问题,获得的训练数据难以覆盖整个飞行包线的各种过渡工作状态,为此本文提出一种基于相似变换的推力估计数据处理方法。通过机理分析选择推力估计器输入,以相似变换对推力估计的输入和输出数据进行处理,并设计了基于输入延迟的深层动态神经网络来实现动态推力估计。非训练数据区域的动态仿真结果表明,相似变换后,深层动态神经网络的最大推力估计误差降低了62.20%,平均误差降低了43.50%;未进行相似变换时,相比深层静态神经网络,深层动态神经网络的最大推力估计误差降低了43.42%,平均误差降低了2.35%,仿真结果表明了本文所提出的数据处理方法和动态推力估计结构有效性。     

Pursuer identification and time-to-go estimation using passive measurements from an evader

We present an algorithm for identifying the parameters of a proportional navigation guidance missile (pursuer) pursuing an airborne target (evader) using angle-only measurements from the latter. This is done for the purpose of classifying the missile so that appropriate counter-measures can be taken. Mathematical models are constructed for a pursuer with a changing velocity, i.e., a direction change and a speed change. Assuming the pursuer is launched from the ground with fixed thrust, its motion can be described by a four-dimensional parameter vector consisting of its proportional navigation constant and three parameters related to thrusting. Consequently, the problem can be solved as a parameter estimation problem, rather than state estimation and we provide an estimator based on maximum likelihood (ML) to solve it. The parameter estimates obtained can be mapped into the time-to-go until intercept estimation results are presented for different scenarios together with the Cramer-Rao lower bound (CRLB), which quantifies the best achievable estimation accuracy. The accuracy of the time-to-go estimate is also obtained. Simulation results demonstrate that the proposed estimator is efficient by meeting the CRLB.     

Multiple scan joint probabilistic data association

This paper presents a multiple scan or n-scan-back joint probabilistic data association (JPDA) algorithm which addresses the problem of measurement-to-track data association in a multiple target and clutter environment. The standard single scan JPDA algorithm updates a track with weighted sum of the measurements which could have reasonably originated from the target in track. The only information the standard JPDA algorithm uses is the measurements on the present scan and the state vectors and covariance matrices of the present targets. The n-scan-back algorithm presented here uses multiple scans of measurements along with the present target information to produce better weights for data association. The standard JPDA algorithm can utilize a formidable amount of processing power and the n-scan-back version only worsens the problem. Therefore, along with the algorithm presentation, implementations which make this algorithm practical are discussed and referenced. An example is also shown for a few n-scan-back window lengths     

DOA estimation for attitude determination on communication satellites

In order to determine an appropriate attitude of three-axis stabilized communication satellites, this paper describes a novel attitude determination method using direction of arrival （DOA） estimation of a ground signal source. It differs from optical measurement, magnetic field measurement, inertial measurement, and global positioning system （GPS） attitude determination. The proposed method is characterized by taking the ground signal source as the attitude reference and acquiring attitude information from DOA estimation. Firstly, an attitude measurement equation with DOA estimation is derived in detail. Then, the error of the measurement equation is analyzed. Finally, an attitude determination algorithm is presented using a dynamic model, the attitude measurement equation, and measurement errors. A developing low Earth orbit （LEO） satellite which tests mobile communication technology with smart antennas can be stabilized in three axes by corporately using a magnetometer, reaction wheels, and three-axis magnetorquer rods. Based on the communication satellite, simulation results demonstrate the effectiveness of the method. The method could be a backup of attitude determination to prevent a system failure on the satellite. Its precision depends on the number of snapshots and the input signal-to-noise ratio （SNR） with DOA estimation.     

基于共轭循环平稳特性的二维波达方向估计方法

 提出了一种具有阵列孔径扩展能力的共轭循环平稳二维波达方向（DOA）估计方法。该方法通过引入伪采样,充分利用了阵元输出之间共轭循环互相关函数的时间维信息,扩展了阵列有效孔径,提高了算法DOA估计精度,具有较好的低信噪比适应能力。该方法避免了最优时延选择问题,无需谱峰搜索,且其二维角度参数能够自动配对,具有较低的计算量。计算机仿真结果验证了该方法的有效性。     

非线性热传导逆问题的表面热流辨识方法

当材料的热物性参数随温度变化时,其内部的热传导方程是一非线性偏微分方程,对应的热传导逆问题称为非线性热传导逆问题。本文建立了非线性热传导逆问题的两种表面热流辨识方法:顺序函数法和共轭梯度法,介绍了这两种辨识方法的基本思想和具体算法推导,并针对典型算例进行了仿真辨识,结果表明:两种辨识方法虽然在算法构造、计算效率方面存在一定的差异,但都能给出较好的辨识结果,并且算法受测量噪声的影响较小,具有较好的鲁棒性。     

HRR Detector for Slow-Moving Targets in Sea Clutter

The radar detection of targets in the presence of sea clutter has historically relied upon the radial velocity of targets with respect to the radar platform either by exploiting the relative target Dopplers (for targets with sufficient radial velocity) or by discerning the paths targets traverse from scan to scan. For targets with little to no radial velocity component, though, it can become quite difficult to differentiate targets from the surrounding sea clutter. This paper addresses the detection of slow-moving targets in sea clutter using a high resolution radar (HRR) such that the target has perceptible extent in range. Under the assumption of completely random sea clutter spikes based on an epsiv-contaminated mixture model with the signal and clutter powers known, optimal detection performance results from using the likelihood ratio test (LRT). However, for realistic sea clutter, the clutter spikes tend to be a localized phenomenon. Based upon observations from real radar data measurements, a heuristic approach exploiting a salient aspect of the idealized LRT is developed which is shown to perform well when applied to real measured sea clutter.