Auto-normalization algorithm for robotic precision drilling system in aircraft component assembly

A novel approach is proposed to detect the normal vector to product surface in real time for the robotic precision drilling system in aircraft component assembly, and the auto-normalization algorithm is presented based on the detection system. Firstly, the deviation between the normal vector and the spindle axis is measured by the four laser displacement sensors installed at the head of the multi-function end effector. Then, the robot target attitude is inversely solved according to the auto-normalization algorithm. Finally, adjust the robot to the target attitude via pitch and yaw rotations about the tool center point and the spindle axis is corrected in line with the normal vector simultaneously. To test and verify the auto-normalization algorithm, an experimental platform is established in which the laser tracker is introduced for accurate measurement. The results show that the deviations between the corrected spindle axis and the normal vector are all reduced to less than 0.5°, with the mean value 0.32°. It is demonstrated the detection method and the auto-normalization algorithm are feasible and reliable.     

三轴稳定卫星无陀螺姿态确定算法研究

针对三轴稳定卫星进行了正常飞行模式下无陀螺姿态确定算法研究，采用磁强计、地球敏感器和太阳敏感器组合获得姿态数据，利用四元数法和高斯－马尔可夫过程建立了姿态确定估计器算法模型。通过数学仿真证明，此姿态确定算法能够对星体姿态进行较精确的估计或校正，满足卫星控制精度要求。     

大型壁板数控钻铆的三点快速调平算法

 针对传统机翼壁板铆接过程中托架调平所存在的问题，提出一种基于有限曲面加工区域的三点调平算法。利用机翼表面上待钻铆点附近三点的坐标来表征该铆接区域的空间姿态，通过钻铆系统的几何结构模型所确定的坐标变化矩阵，逆解出调平所需的各运动副位移增量。在钻铆系统结构模型和机翼曲面方程的基础上建立三点选取的优化模型，并利用外点罚函数法确定其优化解。西安飞机工业(集团)责任有限公司ARJ21新支线飞机的机翼壁板试验件数控钻铆结果表明，该算法能够实现较高的加工精度和调平效率。     

三自由度GMA油膜轴承可视化实验装置

给出了一种三自由度超磁致伸缩驱动器（GMA）油膜轴承可视化实验装置,介绍了它的组成、工作原理及调整方法。该实验装置利用涡轮蜗杆-丝杠传动机构调整实验主轴竖直高度,采用十字滑台、GMA、模具弹簧调整实验轴承在水平面的位置,方便改变实验轴承偏心率,并可利用GMA控制轴承座,减少转子系统振动。在实验台上,进行了椭圆轴承油膜的温度和压力测量以及轴心静平衡位置调整实验。结果表明:通过控制椭圆轴承短轴油膜来调整所支撑转子系统轴心静平衡位置的效果更明显。该实验台可以采集旋转速度在0~10 000 r/min之间的转子轴心轨迹、控制转子工频振动、观察油膜和气穴的形成与破裂实验,为GMA油膜轴承动态性能实验研究打下了一定基础。      

阶梯钻钻削钛合金实验

采用自主磨制的阶梯钻对钛合金进行钻削实验,并与普通麻花钻进行对比。分析了不同加工参数下的钻削力、切屑形态、孔径、孔壁表面粗糙度以及孔出入口毛刺。实验结果表明:钻削力随着主轴转速的增大而减小,随着进给量的增大而增大。相比普通麻花钻,阶梯钻产生的钻削力更小,切屑尺寸更小,排出顺畅,孔径值接近于钻头直径,孔壁表面粗糙度值更小,孔出入口毛刺少。     

运载火箭铝合金叠层壁板自动化制孔工艺对钻孔毛刺影响的研究

为满足运载火箭大型舱段壁板的自动钻铆对制孔质量的要求,本文对典型铝合金叠层进行了自动化制孔试验,采用正交试验分析了主轴转速、进给量和刀具锋角三种制孔参数对出孔毛刺高度的影响,同时进行了不同压紧力作用下制孔试验,研究了压紧力对叠层层间毛刺高度的影响规律。试验表明,在适当的钻削参数下可实现运载火箭铝合金叠层壁板的高质量制孔,叠层制孔层间毛刺可控制在0.045mm左右,出口毛刺高度﹤0.127mm。     

某钛合金深盲孔零件加工工艺研究

利用内冷钻削方法,保证切削液通过主轴和刀具直接喷射到切削表面进行冷却并排出铁削,有效地解决了薄壁深盲孔零件的加工问题,提升了零件的加工质量及加工效率.     

KFRP复合材料螺旋铣削工艺制孔质量

文摘凯夫拉纤维增强复合材料(KFRP)在钻削过程中会产生严重的分层、起毛等缺陷,难以满足装配工序的要求。本文将螺旋铣削工艺运用于KFRP复合材料制孔,进行了偏心距、主轴转速和刀具类型的单因素试验,以分层因子、起毛面积和孔径偏差表征KFRP复合材料螺旋铣削的制孔质量,深入研究不同工况下的缺陷抑制机理和制孔质量。结果表明,偏心距、主轴转速和刀具结构对制孔质量均有显著影响,采用波形四刃铣刀在偏心距0.5 mm和主轴转速4 000 r/min工况下的制孔质量最好,分层因子和孔径偏差分别为1.27和1.2%,起毛面积比二刃铣刀下降了13.7%。     

基于磁场定向控制理论的无刷直流电机控制

磁场定向控制(FOC)理论是永磁同步电机(PMSM)最常用的控制方法之一。该方法需要电机转子瞬时精确位置,因此限制了其在使用霍尔位置传感器的无刷直流电机(BLDCM)上的应用。为了能够在BLDCM上应用FOC理论,又不增加电机成本,在现有霍尔位置传感器的基础上,提出了一种根据霍尔传感器的输出信号,通过计算前一个扇区平均转速的方法估计转子精确位置。使用MATLAB/Simulink软件对该估算方法进行了仿真,并搭建了以TI 的TMS320F28069 DSP为核心的试验系统,通过自动代码生成技术完成算法的编程,可以较好地应用于BLDCM的控制,在一些应用场合可以代替PMSM从而降低使用成本。     

大型复合材料构件连接装配二次损伤及抑制策略

在分析复合材料构件成型和制孔过程中产生缺陷的基础上,从构件成型质量、连接孔加工质量和连接孔配合质量3个方面研究了影响装配应力分布的主要因素及其影响规律。研究发现,装配间隙为1.0mm时,连接区最大应力可达537MPa;垂直度误差为1°时,连接区最大应力超过300MPa;连接孔同轴度误差为0.03mm时,连接区最大应力可达443MPa。装配应力过大引起材料内部成型缺陷和制孔损伤的进一步扩展,形成二次损伤,严重影响装配质量。通过合理设计结构和铺层、优化成型工艺和制孔参数,可以减少初始损伤;采用自动化装配技术、优化工装结构、合理安排装配工序和应用填隙补偿工艺降低装配应力,进而有效抑制二次损伤的诱发与扩展,为实现大型复合材料承力构件的高质量精准连接装配提供理论方法和技术支持。     

Analysis of Chang’e-5 lunar core drilling process

Chang’e-5 explorer successfully acquired lunar regolith core samples from depths of greater than 1 m of lunar surface. This study analyzed the lunar core drilling process based on the telemetry data, image information, and returned samples to optimize the sampling device design and enhance the understanding of the lunar regolith. In particular, a prediction method for the projected drilling path and local terrain fitting of drilling dip angle was proposed based on the flight events recorded during the core drilling process and the image information acquired before, during, and after sampling. The results revealed that the drilling dip angle of Chang’e-5 was approximately 2.3°, and the deviation of the drilling length and depth was less than 2 mm. For continuous drilling, a fusion method based on telemetry data and image information was applied to determine the demarcation point of drilling with and without the lunar soil. The position of the demarcation point implied that the drilling point remained at approximately 6 mm loose soil, thereby lagging the action of the force response. Additionally, a characteristic parameter comparison method was proposed for the lunar and ground drilling to analyze the status of the lunar soil. Furthermore, the analysis results revealed that the majority of the Chang’e-5 drilling samples were derived from 0–73.8 cm below the lunar surface and few samples were extracted below 73.8 cm, as the drilling encountered several rocky regions. Moreover, the drilling point exhibited two prominent stratification variations at ～28.7 cm and ～70 cm below the lunar surface. Ultimately, the preliminary relationship between sample dissected position in soft tube and drilling displacement was analyzed. The segmented estimation results can support research on subsurface lunar soil.     

高分影像辅助下的航空高光谱严密几何检校方法

 惯性测量单元(IMU)与传感器视准轴的偏心角和偏心矢量是造成航空线阵列高光谱数据几何校正误差的主要原因之一。在分析偏心角与偏心矢量误差来源之后提出该误差由IMU主轴与传感器主轴的角度偏差、测区固定偏差、GPS中心与传感器投影中心相对偏差组成,在此基础上建立了较为严密的检校模型。针对模型解算时需要大量高精度控制点的问题,提出了一种高分影像辅助下的亚像元精度控制点自动提取方法。通过多地区、多传感器高光谱航测实验表明,亚像元精度控制点能有效提高模型解算精度。新检校模型可获得亚像元校正精度,推扫式传感器——应用型机载成像光谱仪(AISA)建模中误差约为0.39个像元,摆扫式传感器——实用型模块化成像光谱仪(OMIS)建模中误差约为0.23个像元,校正后的影像可直接进行拼接。     

双自由度侧杆操纵力测量系统设计与实现

在侧杆操纵的民机中,侧杆的操纵力需要满足飞行品质以及适航规章的要求,因此必须对侧杆的操纵力进行准确测量。针对侧杆具有的双自由度运动及侧杆表面形态复杂的特性,设计了一套操纵力测量系统。该系统能够精确控制侧杆的运动方向,使侧杆在一个平面内运动,并通过特殊的机制使力传感器与侧杆运动轴线垂直,保证测试的精度。基于LabView 设计了测试软件,能够实时地显示力、位移以及滞环曲线。     

树脂基纤维复合材料钻削研究进展

主要介绍了树脂基纤维复合材料钻削过程中的钻削力、钻削温度、加工表面质量等钻削性能及材料去除机理、缺陷形成机理、刀具磨损机理等钻削机理方面的研究现状;阐述了树脂基纤维复合材料钻削工艺及钻头改进方面的最新研究进展,并对树脂基纤维复合材料钻削加工技术的下一步研究重点进行了展望。     

Defect suppression mechanism of ultrasonic vibration-assisted drilling carbon fiber/bismaleimide composite

Ultrasonic vibration-assisted drilling (UVAD) has recently been successfully applied in the drilling of carbon fiber reinforced polymer/plastic (CFRP) due to its high reliability. Multiple defects have been observed in the CFRP drilling process which negatively affects the quality of the hole. The carbon fiber/bismaleimide (BMI) composites is an advanced kind of CFRPs with greater strength and heat resistance, having been rapidly applied in lightweight and high temperature resistant structures in the aerospace field. To suppress the defect during the drilling of carbon fiber/BMI composites, it is necessary to comprehensively understand the defect formation and suppression mechanism at different positions. In this study, the defects formation in both conventional drilling (CD) and UVAD were observed and analyzed. The variation trend in the defect factor and thrust force with the spindle speed and feed rate were acquired. The results revealed that the UVAD could significantly enhance the hole’s quality with no delamination and burr. Meanwhile, the defect suppression mechanism and thrust force in UVAD were analyzed and verified, where the method of rod chip removal affected the exit defect formation. In summary, UVAD can be considered a promising and competitive technique for drilling carbon fiber/BMI composites.     

CFRP在钻削加工中的声发射特性

文摘根据CFRP钻削过程中缺陷的产生机理,用声发射传感器采集钻削过程中的声发射信号有效值电压(RMS)。分析了在不同钻削参数下的RMS,对孔的入口处撕裂与出口处撕裂对应的RMS进行识别。结果表明:在钻削过程中,入口处和出口处撕裂会引起RMS的突变,能够有效的进行识别;主轴转速一定时,RMS随着进给量的增大而增大;进给量一定时,RMS随着主轴转速的增大而增大。     

Modeling and experiment of grinding wheel axial profiles based on gear hobs

Hobbing is one of the crucial gear manufacturing processes with high precision and high efficiency. In order to improve the accuracy of hobbing and hob relief grinding, more precise grinding wheels are demanded for relief grinding in the production of gear hobs. In this paper, a new and accurate mathematical method for calculating the axial profile of grinding wheel based on the corresponding gear hob to be ground is proposed. Considering that most researches have been conducted to focus on the optimization of hob geometric feature and only can be applied to a specific type of hand of helix and rake angle of gear hobs. The method in this paper can be served as a general algorithm for generating axial profile of grinding wheels on the basis of the spatial envelope theory, the principle of coordinate system transformation, and studies on normal profile of single-tooth. The accuracy of grinding hobs is based on applying the approach in practical manufacturing. Taking two typical different kinds of pre-grinding gear hobs as examples for calculation and experiment, the results of tooth profile errors strengthen the position that the validity and feasibility of this method, it can be employed for gear hob design and grinding processing.     

高低频复合振动钻削CFRP/钛合金叠层结构试验

针对碳纤维增强复合材料（CFRP）和钛合金叠层结构在传统钻削过程中切削温度高、加工质量差等问题,基于低频振动钻削和高频（超声）振动钻削的优势,提出了高低频复合振动钻削的加工方法。采用自主研制的高低频复合振动钻削装置,对CFRP/钛合金叠层结构进行了制孔试验,对比研究了普通钻削、超声钻削、低频振动钻削和高低频复合振动钻削4种方式下的切削力、钛合金切屑形貌、切削温度和CFRP孔加工质量。结果表明：4种加工方式中,高低频复合振动钻削的轴向力波动相对较大,切削温度显著降低,产生的钛合金切屑呈不连续扇形且整体尺寸最小,CFRP孔出入口及孔壁的损伤程度最低,显著提高了加工质量,为复合材料叠层结构一体化制孔加工提供了指导意义。     

传感器参数误差下的运动目标TDOA/FDOA无源定位算法

在运动目标无源定位系统中，许多算法的前提是精确已知传感器的位置以及速度，但实际情况下可利用的传感器的参数均会存在一些噪声扰动。针对这一问题，提出一种改进的两步加权最小二乘（TSWLS）时差（TDOA）与频差（FDOA）定位算法。该算法是一种闭式算法并且分为2步。第1步与经典的两步加权最小二乘算法相同，第2步进一步研究了额外变量与目标参数之间的关系并且建立了新的矩阵方程。随后，利用加权最小二乘技术给出了最终解。理论分析证明了在测量噪声较小时该算法能够达到克拉美罗界（CRLB）。所提算法具有计算复杂度低，实时性高的优点；另外，经过适当的维度调整，该算法同样适用于对多非相交源进行定位求解。计算机仿真进一步证明了理论分析的正确性。     

面向航天器微低重力仿真的大型超平支撑平台精密装配技术研究

大型超平支撑平台作为航天器微低重力仿真的大型精密试验设备,具备大尺寸、高承载刚度、全自动精密调节等特点。通过对大型超平支撑平台装配要求及难点分析,构建装配系统组成,制定装配工艺流程,设计调节机构及调节工艺流程,并针对虚拟轮廓构建、精密测量、装配路径规划、调控策略等数字化自动装配关键技术进行研究,最终实现大型超平支撑平台的快速、精密测量与调节,高效率、高质量地完成200块平台的精确装配。