Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

Modeling of a new ZVS bi-directional dc-dc converter

A dual half-bridge (DHB) bidirectional dc-dc converter is a new proposed topology that has the advantages of decreased number of devices, soft-switching implementation, low cost, and high efficiency. Typical applications of this converter are the auxiliary power supply in fuel cell vehicles and battery charging and discharging systems where the power density, cost, weight, and reliability are critical factors. A switching-frequency-dependent state-space averaged model of the converter is developed here for either direction of power flow. This averaged model can be used to derive the steady-state characteristics and small signal dynamics of the proposed topology. It also provides a fast simulation tool to investigate the transient response of the converter. The simulated waveforms of the mathematical model are compared with the detailed circuit simulation to verify the accuracy of the modeling.     

Battery charger design for the Columbus MTFF power system

A novel pulsewidth-modulated (PWM) dc-dc converter topology is proposed for the battery charge regulator (BCR) of the Columbus Man-Tended Free-Flyer (MTFF) power system. The system is a regulated bus system. Bus voltage control is implemented at the input of the BCR. The use of a conventional buck topology with PWM conductance control at the input results in a second-order behavior. A study of new PWM dc-dc converter topologies has been made to attain a suitable topology. The proposed converter topology is designed and a breadboard including the control loop has been built and tested. The experimental results show that the converter operates according to the design constraints.     

Analysis and design of (LC)(LC)-type series-parallel resonantconverter

A series-parallel resonant converter employing (LC)(LC)-type tank circuit operating in lagging power factor (PF) mode is presented and analyzed using complex ac circuit analysis. Design curves are obtained and the converter is optimized under certain constraints. Detailed Space Integrated Control Experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load conditions. Results obtained from an experimental converter are also presented. The results obtained from the theory, SPICE simulation, and the experimental converter are compared. The proposed converter has high efficiency from full load to very light load (<10%). Switching frequency variation required for a wide change in the load (near load open circuit to full load) is narrow compared with the series resonant converter (SRC)     

Single-phase power-factor-correction AC/DC converters with threePWM control schemes

Three pulse-width modulation (PWM) control schemes for a single-phase power-factor-correction (PFC) AC/DC converter are presented to improve the power quality. A diode bridge with two power switches is employed as a PFC circuit to achieve a high power factor and low line current harmonic distortion. The control schemes are based on look-up tables with hysteresis current controller (HCC) to generate two-level or three-level PWM on the DC side of diode rectifier. Based on the proposed three control schemes, the line current is driven to follow the sinusoidal current command which is in phase with the supply voltage, and two capacitor voltages on the DC bus are controlled to be balanced. The simulation and experimental results of a 1 kW converter with load as well as line voltage variation and shown to verify the proposed control schemes. It is shown that unity PFC is achieved using a simple control circuit and the measured line current harmonics satisfy the IEC 1000-3-2 requirements     

一种新型电解电源设计及其实验研究

从电解电源的高频高效化、绿色化、数字化及智能化的发展方向出发,利用电流增强原理,设计了一种开关管带并联辅助网络的零电压全桥软开关电路拓扑,具有节能增效、可靠性高的优点.采用TMS320LF 2407A为核心控制芯片.得到了全桥移相PWM输出波形,并设计了反馈信号调理电路与后端驱动电路,电路形式简单紧凑,实现了软开关电解电源的全数字化控制.     

PWM full-bridge converter with natural input power factor correction

A pulsewidth modulated (PWM) full-bridge converter that simultaneously performs input power factor correction (PFC) and DC-DC conversion is proposed. The converter is the same as the standard voltage-fed PWM full-bridge converter with a diode-bridge low-pass filter front end, but with a slight modification that results in an improvement in power factor that is sufficient to satisfy the EN61000-3-2 requirements for electrical equipment. The operation of the converter is explained and analyzed, and the results of the analysis are used to determine the converter's steady-state characteristics, which are discussed in detail. A design procedure for the selection of components is then derived and demonstrated with an example. The feasibility of the converter and its ability to satisfy EN61000-3-2 requirements on electrical equipment is shown with results obtained from an experimental prototype.     

Full bridge ZCS PWM converter for high-voltage high-powerapplications

This paper presents a comprehensive study of a full bridge (FB) zero-current switched (ZCS) PWM converter which is suitable for high-voltage and high-power DC application that achieves ZCS for all active switches, and zero-voltage-switched (ZVS) operation for all diodes on the high voltage side. The given converter utilizes component parasitic parameters, particularly for the high-voltage transformer, and employs fixed-frequency phase-shift control to implement soft-switching commutations. Detailed steady state analysis of the converter power stage is presented for the first time and the major features of the converter's power stage are discussed. Small-signal characteristics are also presented and accompanied by a discussion of the controller design and implementation. A design example is also presented based on the steady state analysis and is validated by simulation. Theoretical and simulated results are in good agreement     

Alternate forms of the PWM switch models

Vorperian's pulsewidth modulation (PWM) switch model consists of a PWM transformer and a nonlinear resistor. The recognition that any of the three transformer terminals can serve as the common terminal leads to two alternate PWM transformer models and the corresponding two alternate PWM switch models. For a given PWM dc-dc converter, one of the three PWM switch models is more “natural” for graphic-oriented analysis/design, e.g., it allows the idealized converter to be analyzed by inspection. Furthermore, all three PWM transformers may be used to graphically manipulate the converter circuit to a form that can be analyzed by inspection. The alternate forms of the PWM transformers and the PWM switch models are effective as graphic-oriented teaching and learning tools for PWM converters. This is demonstrated using examples based on the boost converter and the Cuk converter     

A fixed frequency LCL-Type series resonant converter

A fixed frequency LCL-type series resonant converter (SRC) which uses an inductive output filter is proposed. Steady-state analysis of the converter is presented using complex ac circuit analysis. Based on the analysis, a simple design procedure is given. Detailed space integrated control experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load and supply voltage conditions. Also, detailed experimental results obtained from a metal-oxide-semiconductor field-effect transistor (MOSFET) based 500 W converter are presented to verify the analysis and SPICE simulation results. The results obtained from the analysis, SPICE simulation and the experimental converter are compared. The proposed converter requires a narrow variation in pulsewidth while maintaining lagging power factor mode of operation for a very wide variation in the load as well as supply voltage     

Single-Stage Single-Switch Switched-Capacitor Buck/Buck-Boost-Type Converter

A new dc-dc converter featuring a steep step-down of the input voltage is presented. It answers a typical need for on-board aeronautics modern power architectures: power supplies with a large conversion ratio able to deliver an output voltage of 1–1.2 V. The proposed structure is derived from a switched-capacitor circuit integrated with a buck converter; they share the same active switch. The proposed solution removes the electromagnetic interference (EMI) emission due to the large di/dt in the input current of the switched-capacitor power supplies. Compared with a quadratic buck converter, it presents a similar complexity, a smaller reduction in the line voltage at full load (but less conduction losses due to smaller input inductor current and capacitor voltage), lower voltage stresses on the transistor and diodes, lower current stresses in the diodes, and smaller size inductors. A similar structure using a buck-boost converter as the second stage is also presented. The experimental results confirm the theoretical developments.     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

A New Resonant Mode Amplifier Produces Clean AC Power

A new resonant mode power amplifier design is described which has a number of advantages over the power amplifiers available today. In particular, it has low or no EMI because of the nature of its operation. The new amplifier design is based upon a resonant mode dc-dc converter used in a push-pull configuration. All the advantages of the resonant mode power converters, such as high efficiency, small size and weight, excellent dynamic performance, low or no EMI (compared to PWM switch mode power converter), etc., are present in this new design.     

Design optimization for asymmetrical ZVS-PWM zeta converter

In this paper, a new soft-switching Zeta converter with an asymmetrical pulsewidth modulation (PWM) control is proposed. The proposed Zeta converter has the features of constant frequency operation, zero voltage switching (ZVS), and low voltage stress on the active switches. Moreover, it can achieve high power density, high efficiency, low switching loss, and low component count, which make converter operation at low to medium power level feasible. Operational principle of the Zeta converter is presented in detail, and a specific example is designed and implemented to verify its feasibility.     

基于TMS320F2812生成移相PWM的2种办法

移相 PWM波是很多开关电源常用的驱动脉冲信号。双向全桥直流变换器(Bidirectional-Full-Bridge DCDC Converter,BDC)在双重移相控制方式下时需要 4组两两互补的移相 PWM波。文章基于 TMS320F2812型 DSP(Digital Signal Processor)分析了 2种生成移相 PWM的方法。为提高双向全桥直流变换器工作的安全性和可靠性,为移相 PWM波设置死区时间。对所提出的方法进行测试后结果良好,对于双向全桥直流变换器闭环控制系统的构建具有重要意义。     

Current Injected Equivalent Circuit Approach to Modeling Switching DC-DC Converters

A new current injected equivalent circuit approach (CIECA) to modeling switching dc-dc converter power stages is developed, which starts with the current injected approach and results in either a set of equations which completely describe input and out-put properties or an equivalent linear circuit model valid at small signal, low frequency levels. This approach to modeling switching dc-dc converter power stages has the merits but not the demerits of both the electronic equivalent circuit state space average approach and the current injected control type approach, namely, 1) the modeling is very clear and is simple whether the converter operates in continuous or discontinuous inductor conduction modes, 2) the modeling results in an equivalent circuit which is very close to the actual converter, and 3) the equivalent circuit can be used directly in the computer for theoretical predictions like SPICE, etc.     

Control technique for high power factor multilevel rectifier

Three control techniques for a high power factor multilevel pulsewidth modulation (PWM) rectifier are proposed. The proposed rectifier is based on series connection of full-bridge cell to achieve a high power factor, low current distortion, low voltage stress of power semiconductors and two balanced output voltages. The look-up table is used in the proposed control schemes to reduce the hardware circuit. A capacitor voltage compensator is used to balance two dc capacitor voltages in order to obtain high quality PWM voltage pattern. Based on the proposed control schemes, two-level or three-level PWM pattern can be generated on the ac side of the adopted rectifier. The proposed techniques for a high power factor multilevel rectifier illustrate its validity and effectiveness through the respective simulations and experiments. According to the measured results, the current harmonics drawn from the mains meet the International Electrotechnical Commission (IEC) 1000-3-2 limits     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

General rules for signal flow graph modeling and analysis of dc-dc converters

Signal flow graph (SFG) nonlinear modeling approach is well known for modeling dc-dc converters. However, all possible SFGs of a given dc-dc converter system will not yield the generalized graph. A systematic procedure and guidelines for developing unified flow graph models of the dc-dc boost converters, from which complete behavior can be determined is presented. Usefulness of the proposed method is demonstrated through examples. As an illustration a 2-cell cascade boost and interleaved boost converter systems are taken as examples. Derivation of large, small-signal and steady-state models from generalized flow graph is also demonstrated. Large-signal model is developed and programmed in TUTSIM simulator. Large-signal, responses against supply and load disturbances are obtained. Experimental observations are provided to validate the proposed algorithm.     

Improved ZCS-PWM commutation cell for IGBTs application

An improved zero-current-switching pulsewidth-modulated (ZCS-PWM) commutation cell is presented, which is suitable for high-power applications using insulated gate bipolar transistors (IGBTs) as the power switches. It provides ZCS operation for active switches and zero-voltage-switching (ZVS) operation for passive switches. Besides operating at constant frequency and reducing commutation losses, the proposed ZCS-PWM switch cell has no additional current stress and conduction loss in the main switch. To demonstrate the feasibility of the proposed ZCS-PWM commutation cell, it was applied to a boost converter. Operating principle, theoretical analysis, design guidelines, and a design example are described and verified by experiment results obtained from a prototype rated 1 kW and operating at 40 kHz. The PWM switch model and state-space averaging approach is also used to estimate and examine the steady-state and dynamic character of ZCS-PWM boost converter system. Finally, the application of the proposed soft-switching technique in the dc-dc nonisolated converters is presented.