Cosmic radiation exposure of biological test systems during the EXPOSE-E mission

In the frame of the EXPOSE-E mission on the Columbus external payload facility EuTEF on board the International Space Station, passive thermoluminescence dosimeters were applied to measure the radiation exposure of biological samples. The detectors were located either as stacks next to biological specimens to determine the depth dose distribution or beneath the sample carriers to determine the dose levels for maximum shielding. The maximum mission dose measured in the upper layer of the depth dose part of the experiment amounted to 238±10 mGy, which relates to an average dose rate of 408±16 μGy/d. In these stacks of about 8?mm height, the dose decreased by 5-12% with depth. The maximum dose measured beneath the sample carriers was 215±16 mGy, which amounts to an average dose rate of 368±27 μGy/d. These values are close to those assessed for the interior of the Columbus module and demonstrate the high shielding of the biological experiments within the EXPOSE-E facility. Besides the shielding by the EXPOSE-E hardware itself, additional shielding was experienced by the external structures adjacent to EXPOSE-E, such as EuTEF and Columbus. This led to a dose gradient over the entire exposure area, from 215±16 mGy for the lowest to 121±6 mGy for maximum shielding. Hence, the doses perceived by the biological samples inside EXPOSE-E varied by 70% (from lowest to highest dose). As a consequence of the high shielding, the biological samples were predominantly exposed to galactic cosmic heavy ions, while electrons and a significant fraction of protons of the radiation belts and solar wind did not reach the samples.     

Ground based ISS payload microgravity disturbance assessments

In order to verify that the International Space Station (ISS) payload facility racks do not disturb the microgravity environment of neighboring facility racks and that the facility science operations are not compromised, a testing and analytical verification process must be followed. Currently no facility racks have taken this process from start to finish. The authors are participants in implementing this process for the NASA Glenn Research Center (GRC) Fluids and Combustion Facility (FCF). To address the testing part of the verification process, the Microgravity Emissions Laboratory (MEL) was developed at GRC. The MEL is a 6 degree of freedom inertial measurement system capable of characterizing inertial response forces (emissions) of components, sub-rack payloads, or rack-level payloads down to 10(-7) g's. The inertial force output data, generated from the steady state or transient operations of the test articles, are utilized in analytical simulations to predict the on-orbit vibratory environment at specific science or rack interface locations. Once the facility payload rack and disturbers are properly modeled an assessment can be made as to whether required microgravity levels are achieved. The modeling is utilized to develop microgravity predictions which lead to the development of microgravity sensitive ISS experiment operations once on-orbit. The on-orbit measurements will be verified by use of the NASA GRC Space Acceleration Measurement System (SAMS). The major topics to be addressed in this paper are: (1) Microgravity Requirements, (2) Microgravity Disturbers, (3) MEL Testing, (4) Disturbance Control, (5) Microgravity Control Process, and (6) On-Orbit Predictions and Verification.     

Looking ahead: Science requirements for the U.S./International Space Station

During the next eight years the United States, European countries within the European Space Agency, Canada, and Japan will engage in the design and construction of facilities included in the current conceptual design of the U.S./International Space Station. The object will be to build a manned space facility capable of supporting scientific research, technological development, and commercial operations. This paper is directed towards an overview of the essential requirements for successful scientific use of the Space Station. Because specific supporting technologies will change so drastically before heavy use can begin, it is important to discuss the most fundamental aspects of user requirements; namely, (1) What are the characteristics of a remote, manned space facility that can promote first rate scientific use? (2) What does it take to achieve such a facility, and (3) What guidelines can be given such that once the facility is in operation it attracts the best possible scientific talent?     

空间站有效载荷真空支持系统方案评述

有效载荷真空支持系统是空间有效载荷支持系统的重要组成部分,为空间有效载荷实验的顺利进行提供真空环境支持和保证。文章详细分析了国际空间站包括美国“命运号”实验舱（USL）、欧空局哥伦布轨道舱（APM）及日本实验舱（JEM）内的有效载荷真空支持系统方案及使用情况;对美国实验舱内的一号微重力材料科学机柜及微重力燃烧科学机柜内部专用的真空支持系统作了主要介绍;最后提出了我国空间站有效载荷真空支持系统的初步方案设想,即合理安排有效载荷实验进行次序,将废气排放子系统及真空资源子系统合二为一,以节约资源,提高可靠性。     

Multiobjective optimization applied to structural sizing of low cost university-class microsatellite projects

In recent years, there has been continuing interest in the participation of university research groups in space technology studies by means of their own microsatellites. The involvement in such projects has some inherent challenges, such as limited budget and facilities. Also, due to the fact that the main objective of these projects is for educational purposes, usually there are uncertainties regarding their in orbit mission and scientific payloads at the early phases of the project. On the other hand, there are predetermined limitations for their mass and volume budgets owing to the fact that most of them are launched as an auxiliary payload in which the launch cost is reduced considerably. The satellite structure subsystem is the one which is most affected by the launcher constraints. This can affect different aspects, including dimensions, strength and frequency requirements. In this paper, the main focus is on developing a structural design sizing tool containing not only the primary structures properties as variables but also the system level variables such as payload mass budget and satellite total mass and dimensions. This approach enables the design team to obtain better insight into the design in an extended design envelope. The structural design sizing tool is based on analytical structural design formulas and appropriate assumptions including both static and dynamic models of the satellite. Finally, a Genetic Algorithm (GA) multiobjective optimization is applied to the design space. The result is a Pareto-optimal based on two objectives, minimum satellite total mass and maximum payload mass budget, which gives a useful insight to the design team at the early phases of the design.     

Research priorities and plans for the International Space Station-results of the 'REMAP' Task Force

Recent events in the International Space Station (ISS) Program have resulted in the necessity to re-examine the research priorities and research plans for future years. Due to both technical and fiscal resource constraints expected on the International Space Station, it is imperative that research priorities be carefully reviewed and clearly articulated. In consultation with OSTP and the Office of Management and budget (OMB), NASA's Office of Biological and Physical Research (OBPR) assembled an ad-hoc external advisory committee, the Biological and Physical Research Maximization and Prioritization (REMAP) Task Force. This paper describes the outcome of the Task Force and how it is being used to define a roadmap for near and long-term Biological and Physical Research objectives that supports NASA's Vision and Mission. Additionally, the paper discusses further prioritizations that were necessitated by budget and ISS resource constraints in order to maximize utilization of the International Space Station. Finally, a process has been developed to integrate the requirements for this prioritized research with other agency requirements to develop an integrated ISS assembly and utilization plan that maximizes scientific output.     

The development of the hardware for studying biological clock systems under microgravity conditions,using scorpions as animal models

The study of internal clock systems of scorpions in weightless conditions is the goal of the SCORPI experiment. SCORPI was selected for flight on the International Space Station (ISS) and will be mounted in the European facility BIOLAB, the European Space Agency (ESA) laboratory designed to support biological experiments on micro-organisms, cells, tissue, cultures, small plants and small invertebrates. This paper outlines the main features of a breadboard designed and developed in order to allow the analysis of critical aspects of the experiment. It is a complete tool to simulate the experiment mission on ground and it can be customised, adapted and tuned to the scientific requirements. The paper introduces the SCORPI-T experiment which represents an important precursor for the success of the SCORPI on BIOLAB. The capabilities of the hardware developed show its potential use for future similar experiments in space.     

Problems of control arised during the implementation of scientific research program onboard the multipurpose orbital stations

This paper considers the problems of control arised in the process of implementation of experiments and research program performed onboard the multipurpose orbital stations (OS). The features of scientific program are analysed when using permanent OS main of which are the flexibility of the research program, the possibility of experiments rational planning and etc. Taking into account the experience gained during the long-term Salyut-6 and 7 stations operation ways and methods are proposed to increase the effectiveness of investigations based on the requirements definition for technical chracteristics of the research instruments and OS systems, development of operational requirements for erbital stations as well as methods for real time research program planning to be optimized.The development methods allow to receive maximum of useful information from the planned program when the resources are limited or to minimize the required resources at the set useful information. These problems solution is based on the methods of minimum/maximum theory as well as linear programming. The main complication of their solution is connected with a great number of the research program feasibility constraints. When experiments are carried out on scientific modules which are the part of the Mir station this problem comes more complicated due to additional constraints caused by gyropower stabilizers (GS) used in the control system. So far in this case while performing scientific observation the OS orientation should provide “favourable” GS operation mode as well as the required power balance.     

Species and temperature exchange in the atmosphere of “BION-M” spacecraft

On going flights of Foton satellites allow to carry out research in the following domains: effect of space flight and outer space factors such as microgravity, artificial gravity and space radiation on physical processes and biological organisms. Experts from many Russian and foreign scientific institutions participated in the research. Over a period of time from 1973 to 1997 there were launched 11 BION satellites designed by the Central Specialized Design Bureau for carrying out fundamental and applied research in the field of space biology, medicine, radio physics and radiobiology with participation of specialists from the foreign countries.The goal of the present investigation was in developing a numerical simulator aimed at determining gas concentration and temperature fields established inside the scientific module of the spacecraft “Bion-M” and to perform optimization studies, which could meet strong requirements for air quality and temperature range allowable for operation of different biological experiments.     

NASA's in-space technology experiments program: Status and plans

Experience with the Shuttle and free-flying satellites as technology test beds has shown the feasibility and desirability of using space assets as facilities for technology development. Thus, by the time the space station era arrives, technologists will be ready for an accessible engineering facility in space. Along with the scientific and commercial space development communities, the technology development community has been participating in defining requirements for this in-space facility. As the 21st century is approached, it is expected that many flights to the Space Station Freedom will carry one or more RT&E experiments. The experiments are likely to utilize both the pressurized volume, and the external payload attachment facilities. Based on the success of instrumenting the Shuttle itself to obtain ascent and descent aerothermodynamic data a unique, but extremely important, class of experiments will use the space station itself as an experimental vehicle.     

The cost benefits of the Spacelab system to scientific investigations and space applications

In the past, one of the major problems in performing scientific investigations in space has been the high cost of developing, integrating, and transporting scientific experiments into space. The limited resources of unmanned spacecraft, coupled with the requirements for completely automated operations, was another factor contributing to the high costs of scientific research in space. In previous space missions after developing, integrating and transporting costly experiments into space and obtaining successful data, the experiment facility and spacecraft have been lost forever, because they could not be returned to earth. The objective of this paper is to present how the utilization of the Spacelab System will result in cost benefits to the scientific community, and significantly reduce the cost of space operations from previous space programs.The following approach was used to quantify the cost benefits of using the Spacelab System to greatly reduce the operational costs of scientific research in space. An analysis was made of the series of activities required to combine individual scientific experiments into an integrated payload that is compatible with the Space Transportation System (STS). These activities, including Shuttle and Spacelab integration, communications and data processing, launch support requirements, and flight operations were analyzed to indicate how this new space system, when compared with previous space systems, will reduce the cost of space research. It will be shown that utilization of the Spacelab modular design, standard payload interfaces, optional Mission Dependent Equipment (MDE), and standard services, such as the Experiment Computer Operating System (ECOS), allow the user many more services than previous programs, at significantly lower costs. In addition, the missions will also be analyzed to relate their cost benefit contributions to space scientific research.The analytical tools that are being developed at MSFC in the form of computer programs that can rapidly analyze experiment to Spacelab interfaces will be discussed to show how these tools allow the Spacelab integrator to economically establish the payload compatibility of a Spacelab mission.The information used in this paper has been assimilated from the actual experience gained in integrating over 50 highly complex, scientific experiments that will fly on the Spacelab first and second missions. In addition, this paper described the work being done at the Marshall Space Flight Center (MSFC) to define the analytical integration tools and techniques required to economically and efficiently integrate a wide variety of Spacelab payloads and missions. The conclusions reached in this study are based on the actual experience gained at MSFC in its roles of Spacelab integration and mission managers for the first three Spacelab missions. The results of this paper will clearly show that the cost benefits of the Spacelab system will greatly reduce the costs and increase the opportunities for scientific investigation from space.     

Greenhouse design integration benefits for extended spaceflight

It has been demonstrated that plants can be grown in microgravity, and almost every space programme has included experimental greenhouses to investigate technical and biological feasibility, as well as the habitability-related benefits of plant growth activities in space.Aside from nutritional and life support system applications, these benefits include sensory and spatial enhancement of the spacecraft environment, both through the plants as such and the design of their growth chambers, as well as by providing meaningful occupation through individual interaction. In view of long duration missions, plant growth facilities should not be regarded as a desirable add-on, but as an essential component of the habitat.Following a review of existing greenhouse designs and plants grown on past missions, the paper summarizes the benefits of greenhouses and outlines potential forms of architectural integration within the spacecraft interior.     

Space Station atmospheric monitoring systems.

A technology assessment study on atmospheric monitoring systems was performed by Battelle Columbus Division for the National Aeronautics and Space Administration's John F. Kennedy Space Center under Contract No. NAS 10-11033. In this assessment, the objective was to identify, analyze, and recommend systems to sample and measure Space Station atmospheric contaminants and identify where additional research and technology advancements were required. To achieve this objective, it was necessary to define atmospheric monitoring requirements and to assess the state of the art and advanced technology and systems for technical and operational compatibility with monitoring goals. Three technical tasks were defined to support these needs: Definition of Monitoring Requirements, Assessment of Sampling and Analytical Technology, and Technology Screening and Recommendations. Based on the analysis, the principal candidates recommended for development at the Space Station's initial operational capability were: (1) long-path Fourier transform infrared for rapid detection of high-risk contamination incidences, and (2) gas chromatography/mass spectrometry utilizing mass selective detection (or ion-trap) technologies for detailed monitoring of extended crew exposure to low level (ppbv) contamination. The development of a gas chromatography/mass spectrometry/matrix isolation-Fourier transform infrared system was recommended as part of the long range program of upgrading Space Station trace-contaminant monitoring needs.     

EXPOSE-E: an ESA astrobiology mission 1.5 years in space

The multi-user facility EXPOSE-E was designed by the European Space Agency to enable astrobiology research in space (low-Earth orbit). On 7 February 2008, EXPOSE-E was carried to the International Space Station (ISS) on the European Technology Exposure Facility (EuTEF) platform in the cargo bay of Space Shuttle STS-122 Atlantis. The facility was installed at the starboard cone of the Columbus module by extravehicular activity, where it remained in space for 1.5 years. EXPOSE-E was returned to Earth with STS-128 Discovery on 12 September 2009 for subsequent sample analysis. EXPOSE-E provided accommodation in three exposure trays for a variety of astrobiological test samples that were exposed to selected space conditions: either to space vacuum, solar electromagnetic radiation at >110?nm and cosmic radiation (trays 1 and 3) or to simulated martian surface conditions (tray 2). Data on UV radiation, cosmic radiation, and temperature were measured every 10?s and downlinked by telemetry. A parallel mission ground reference (MGR) experiment was performed on ground with a parallel set of hardware and samples under simulated space conditions. EXPOSE-E performed a successful 1.5-year mission in space.     

Enhanced operations efficiency by using the unified synoptic system

The unified synoptic system (USS) was developed by ESA for replacing the existing Columbus display solutions and to unify the display system used on-board and on-ground. USS provides enhanced flight operations efficiency and reduced effort for product preparation, qualification and maintenance for synoptic displays. Additional to its use for Columbus it is installed at JAXA and NASA to support requirements definition and review of NASA generated ISS displays. Due to its advanced capabilities, which go beyond existing known solutions, it has been made available to be reused for future spacecraft EGSEs and control centres (e.g. exploration missions, satellites) as well. Use of synoptic display is mostly guided by operational procedures which are in electronic format. However, till now the full operational benefit has not yet been realized. Procedure viewers and synoptic display systems are completely separate entities. Direct interaction of procedure viewers with synoptic display systems or underlying system control software is not supported at all. Therefore astronauts, flight controllers and operators still have to carry out a lot of mundane activities when executing operational procedures. The USS based procedural display viewer provides the user with a coherent, task oriented user interface for using synoptic displays and executing procedures in an efficient manner.     

Utilisation of the European Retrieval Carrier Eureca for life science research.

Eureca, the European Retrieval Carrier, is a reusable free-flying platform, which will be launched to 500 km altitude and retrieved by the Shuttle. up to 6 months later at 300 km. The first mission of Eureca is dedicated to research in the fields of life sciences and material sciences. The experimental hardware of the first mission will consist of a variety of processing chambers for crystal growth and equipment for biological investigations viz plant growth and protein crystallization, and there is the possibility to perform experiments in the field of exobiology. The Eureca mission offers the opportunity for long time exposure of material and of terrestrial origin to the unique environment of space or to selected factors of it, such as the radiation environment, the space vacuum, extreme temperatures and microgravity conditions.     

时间代价启发式多月基装备协同任务规划方法

针对月球科研站构建中优化整体任务用时的需求,提出时间代价启发式多月基装备协同任务规划方法。面向月球科研站构建过程中的原位和路径任务,构建双类型任务关系图,并提出多位置转移时间代价启发式策略引导此图的搜索方向,使规划器沿局部最短耗时任务路径逐个处理任务,降低装备路径转移的时间代价;提出时间代价启发式装备选择策略,从而均衡月基装备任务负载,缩短装备工作时长。最后,以包含资源开采、物料运输、设施建设等任务的月球科研站构建场景为例,对规划算法进行仿真验证。结果表明,此算法能够生成满足复杂约束的多装备协同规划序列。与传统规划方法相比,本文方法得到的月基装备任务序列冗余路径少、任务用时短,可实现多装备在多任务中的高效分时复用。     

EDEN: a payload dedicated to neurovestibular research for Neurolab

The European Space Agency contributes to the Neurolab mission through the delivery of the ESA Developed Elements for Neurolab (EDEN). Those elements include one set supporting the Autonomic Nervous System experiment and one set supporting the Neurovestibular (so-called ATLAS) experiment. This second set is called the Visual and Vestibular Investigation System (VVIS). This paper describes the main characteristics of the VVIS and its various subsystems. The scientific objectives and operational constraints of the ATLAS experiment to be carried out with this equipment during Neurolab are presented to underline the correspondence between the VVIS design and the scientific requirements. Further scientific and technical perspectives for the VVIS, particularly within the scope of the International Space station, are also proposed.     

An energy balance concept for habitability

Habitability can be formulated as a balance between the biological demand for energy and the corresponding potential for meeting that demand by transduction of energy from the environment into biological process. The biological demand for energy is manifest in two requirements, analogous to the voltage and power requirements of an electrical device, which must both be met if life is to be supported. These requirements exhibit discrete (non-zero) minima whose magnitude is set by the biochemistry in question, and they are increased in quantifiable fashion by (i) deviations from biochemically optimal physical and chemical conditions and (ii) energy-expending solutions to problems of resource limitation. The possible rate of energy transduction is constrained by (i) the availability of usable free energy sources in the environment, (ii) limitations on transport of those sources into the cell, (iii) upper limits on the rate at which energy can be stored, transported, and subsequently liberated by biochemical mechanisms (e.g., enzyme saturation effects), and (iv) upper limits imposed by an inability to use "power" and "voltage" at levels that cause material breakdown. A system is habitable when the realized rate of energy transduction equals or exceeds the biological demand for energy. For systems in which water availability is considered a key aspect of habitability (e.g., Mars), the energy balance construct imposes additional, quantitative constraints that may help to prioritize targets in search-for-life missions. Because the biological need for energy is universal, the energy balance construct also helps to constrain habitability in systems (e.g., those envisioned to use solvents other than water) for which little constraint currently exists.     

Europe's next move

Some time before the end of the first quarter of 1991 the Ministerial Council of the European Space Agency will be taking decisions about the development phases of the Columbus and Hermes programmes. The prospects for completing either programme within the originally approved costs are not bright, and operational costs will be three times the amount the ESA spends on its scientific programme. Are they good value for money? The author argues that Europe is in danger of yielding to others the lead in the next generation of space flight.