电帘除尘技术的研究现状

微尘作为影响探月工程和火星计划成败的一个因素,已经越来越多地引起人们的重视。而电帘除尘技术作为月球和火星探测有效的除尘技术之一,也得到广泛的关注。文章在调研相关文献的基础上,阐述了目前国外电帘除尘技术的研究现状,提出了开展研究工作的建议,对发展我国电帘除尘技术具有一定的参考意义。     

Systems of Gyrodynes with an Additional Degree of Freedom

The systems of gyrodynes installed on a spacecraft body on the one-axis controlled platform are considered. An algorithm to determine the special states and the special surfaces corresponding to them in the region of variation of the total angular momentum is obtained, as well as an algorithm to study the permeability of special surfaces. The results of calculation of the special surfaces for two types of gyro systems are presented.     

Did mineral surface chemistry and toxicity contribute to evolution of microbial extracellular polymeric substances?

Abstract Modern ecological niches are teeming with an astonishing diversity of microbial life in biofilms closely associated with mineral surfaces, which highlights the remarkable success of microorganisms in conquering the challenges and capitalizing on the benefits presented by the mineral-water interface. Biofilm formation capability likely evolved on early Earth because biofilms provide crucial cell survival functions. The potential toxicity of mineral surfaces toward cells and the complexities of the mineral-water-cell interface in determining the toxicity mechanisms, however, have not been fully appreciated. Here, we report a previously unrecognized role for extracellular polymeric substances (EPS), which form biofilms in shielding cells against the toxicity of mineral surfaces. Using colony plating and LIVE/DEAD staining methods in oxide suspensions versus oxide-free controls, we found greater viability of wild-type, EPS-producing strains of Pseudomonas aeruginosa PAO1 compared to their isogenic knockout mutant with defective biofilm-producing capacity. Oxide toxicity was specific to its surface charge and particle size. High resolution transmission electron microscopy (HRTEM) images and assays for highly reactive oxygen species (hROS) on mineral surfaces suggested that EPS shield via both physical and chemical mechanisms. Intriguingly, qualitative as well as quantitative measures of EPS production showed that toxic minerals induced EPS production in bacteria. By determining the specific toxicity mechanisms, we provide insight into the potential impact of mineral surfaces in promoting increased complexity of cell surfaces, including EPS and biofilm formation, on early Earth. Key Words: Mineral toxicity-Bacteria-EPS evolution-Biofilms-Cytotoxicity-Silica-Anatase-Alumina. Astrobiology 12, 785-798.     

空间站诱发污染环境评估与光学表面污染分析技术综述

文章在调研NASA、ESA和俄罗斯相关研究组织的研究结果的基础上,对空间站自身运行引起的外部诱发污染环境对空间站功能表面、敏感载荷和科学试验载荷的影响以及国外在此领域的技术发展水平进行了全面的评述,阐明了深入开展空间站外部诱发污染环境分布规律和空间站表面污染分析技术研究的必要性。     

月球坑内空间环境热流的分布研究

文章推导获得了月面阳光矢量和月球坑内探测器表面关系的表达式,采用蒙特卡罗法数值计算探测器各表面的辐射热流,分析了月球坑内环境辐射热流的分布特征。讨论了月面纬度、月球坑尺寸、月面发射率等参数对探测器表面热流的影响。计算表明:月面纬度增加及月球坑坑口半径的减小均会导致某些时刻阳光无法照射到坑底,从而与其他工况有较大的计算差别,两参数对探测器各面热流的影响规律不同;月面发射率对探测器表面热流的影响作用较大,增加月面发射率能明显降低探测器某些表面的辐射热流。     

一种从混合表面的明暗变化恢复形状的新算法

针对传统的混合表面形状恢复算法存在较大误差的问题,提出了一种基于透视投影的从混合表面的明暗变化恢复形状的新算法.首先,建立了一种改进的Ward反射模型来描述混合表面的反射特性,其次,采用更接近摄像机实际拍摄的透视投影方式,并且假定光源位于摄像机的光心处,构造了新模型下的图像辐照度方程,然后将该方程转化为包含物体表面深度信息的Hamilton-Jacobi偏微分方程,使用Fixed-point Iterative Sweeping方法和2D Central Hamiltonian函数逼近该微分方程的黏性解,进而得到物体表面的三维形状.与同类算法相比,新算法恢复的结果更加准确有效.合成花瓶图像的实验结果表明,与基于正交投影的算法相比,新算法恢复三维形状高度的平均误差和均方根误差均有较大幅度减少.     

Critical conditions of condensation of metal working medium of electric propulsion on spacecraft surfaces

An experimental method for determination of critical conditions of condensation of metal propellants of electric jet engines (EJEs) on the surfaces of materials of spacecraft thermoregulating covers is presented. When the critical conditions are reached, the irreversible process of condensation and formation of thin metal films begins on spacecraft surfaces. A rather high accuracy and universality of the method for metal working media and for various surface materials are based on measurements of the intensity of a light beam generated by a stabilized source and reflected from the surface. The working capacity of the method is demonstrated for measurements carried out for four different materials of the surfaces of thermoregulating covers and cesium vapors.     

Situation studies of aes orbits for solar-Earth space experiments

The questions on the orbit selection for studying various areas of the Earth magnetosphere are discussed. The method of the orbit selection is based on the use of orbital tori and on the construction of areas of orbit set intersection with model surfaces, forming specific areas in the near Earth space: bow shock (BSh), magnetopause (MP) neutral sheet in the magnetosphere tail, cusp etc. Intersections of the “Prognoz” 1–8 orbit set with model surfaces BSh and MP are shown.     

发动机和羽流对地球同步卫星底部辐射加热的计算研究

地球同步卫星工作过程中法兰底座所受的辐射加热对法兰上的控制开关等零件的安全有重要影响。为此,建立了节点网络法计算发动机和隔热屏对卫星法兰底座及控制开关的辐射加热,比较了发动机、隔热屏和羽流3种辐射源的作用大小,还研究了发动机位置的平移对底部法兰及控制开关辐射加热的影响。研究表明:羽流对法兰和控制开关的辐射热流最小,发动机对法兰和控制开关的辐射热流最大;法兰和控制开关上不同侧面受到的辐射加热很不均匀,面向发动机正面的侧面辐射加热最强,面向发动机头部的侧面辐射最小;发动机向后平移可以显著降低法兰和控制开关上辐射热流的最大值。     

Rock surfaces as life indicators: new ways to demonstrate life and traces of former life

Life and its former traces can only be detected from space when they are abundant and exposed to the planetary atmosphere at the moment of investigation by orbiters. Exposed rock surfaces present a multifractal labyrinth of niches for microbial life. Based upon our studies of highly stress-resistant microcolonial fungi of stone monument and desert rock surfaces, we propose that microbial biofilms that develop and become preserved on rock surfaces can be identified remotely by the following characteristics: (1) the existence of spectroscopically identifiable compounds that display unique adsorption, diffraction, and reflection patterns characteristic of biogenerated organic compounds (e.g., chlorophylls, carotenes, melanins, and possibly mycosporines), (2) demonstrably biogenic geomorphological features (e.g., biopitting, biochipping, and bioexfoliation), and (3) biominerals produced in association with biofilms that occupy rock surfaces (e.g., oxalates, forsterite, and special types of carbonates, sulfides, and silicates). Such traces or biosignatures of former life could provide macroscopically visible morphotypes and chemically identifiable products uniquely indicative of life.     

某飞翼布局无人机控制系统重构方法研究

通常是在欧拉坐标系中描述飞机的运动方程,但是当飞机做大幅度的姿态运动时,运动方程的解会出现奇异性.根据某飞翼布局无人机的特点,本文首先建立了基于四元数法的六自由度飞行力学模型.在操纵面的气动数据插值方面,本文用非均匀有理B样条插值法,将插值后的数据进行拟合,得到操纵面气动力系数与舵偏角的关系表达式.在上述基础上,用序列...     

基于数字近景摄影测量的天线变形测量

文章介绍了基于数字近景摄影测量原理的天线变形测量方法。该方法利用2台CCD相机交会摄影来获取被测面图像,并对被测面上特殊标志点进行中心坐标提取,然后利用光束法平差解算标志点中心坐标。测量精度可达到1:50000,可用于卫星天线研制过程中空间环境模拟试验的检验,为卫星天线在轨正常工作提供可靠性保证。     

发射特性对线性各向异性散射介质内瞬态温度分布的影响

考虑各向异性散射介质内的辐射传递方向，本文考察了辐射能的重新分配过程。利用射线踪迹法结合Hottel和Sarofim区域法推导了辐射传递系数(RTCs)。考虑一维各向异性参与性半透明灰介质。两边界表面为镜反射，一个表面半透明，另一个表面不透明。辐射传递系数用于计算辐射热源项。瞬态能量方程由全隐式控制容积法求解。外界辐射加热与对流冷却同时作用于边界表面。考虑四个线性散射相函数。以各向同性散射情况比较，研究不透明边界两侧发射特性和线性散射相函数对瞬态温度分布的影响。结果表明，各向异性散射与各向同性散射介质间的相对温度差异与散射不对称参数近似成正比。     

反折式二元超声速进气道研究

X-51A采用带两级压缩楔面的反折式进气道设计方案,这是一体化权衡设计的结果,要求进气道设计综合各方面因素进行多目标优化。从发动机设计角度出发对类似于X-51A的反折式二元进气道进行了研究,合理选择了进气道的设计变量并运用多目标粒子群优化算法（MOPSO）对带两级压缩楔面的反折式二元进气道按总压恢复系数、流量系数及出口马赫数三个目标函数进行了多目标优化设计,计算中性能指标参数评估基于Euler方程求解得到。通过优化计算得到了带两级压缩楔面的反折式进气道相关性能指标参数最优变化关系及结构方案,可为后续进气道与飞行器一体化权衡提供设计参考。     

机械冲击载荷下固体推进剂热点微观模型探讨

分析了推进剂内部初始裂纹在机械冲击载荷作用下的扩展以及与反应气体产物相互作用。利用Ⅰ、Ⅱ型裂纹扩展、推进剂分解化学动力学模型,建立微观热点模型,研究了裂纹面摩擦、推进剂分解以及裂纹内部气相反应等微观过程。进行数值模拟计算,得出了推进剂产生高温热点或导致冲击点燃的外部条件。认为裂纹间摩擦和气相产物在高速冲击下压缩可导致推进荆热点产生。     

月尘对热控系统的退化影响

月尘对热控系统的退化影响直接威胁到探测器在月面的生存,是探测器热控系统设计时所必须考虑的技术重点和难点之一。随着我国探月工程的深入,急需开展月尘对热控系统影响程度的研究,文章在调研的基础上,阐述了目前国内外在月尘的特性、危害性和防护方面的研究现状,并探讨了针对月面探测器设计上的一些可行的防尘措施。     

航天器表面环境散射返回流污染数值模拟和影响因素分析

针对航天器表面出气分子形成的环境散射返回流污染问题,利用试验粒子Monte Carlo方法对圆球和圆柱体简化航天器表面环境散射返回流进行数值模拟。其中,圆球出气表面的计算结果与已有的DSMC(Direct Simulation Monte Carlo)方法计算结果一致,验证了该方法的正确性。此外,对不同长径比的圆柱表面环境散射进行了计算和分析,结果表明:来流方向垂直于圆柱对称轴时,返回分子主要分布在圆柱体侧面的迎风部位;返回通量比随来流与出气分子质量之比的增加逐渐减小,随来流与出气表面温度之比、来流分子速度比和数密度的增加而增大;不同长径比条件下返回通量比相对于上述4个参数的变化具有相似性和递变性,短粗体的返回通量比最小,长细体的最大,正常圆柱体的则居中;返回通量比相对来流攻角的变化在不同长径比条件下不再具有相似性,而是取决于有效迎风面积。     

Experimental hypervelocity impacts: Implication for the analysis of material retrieved after exposure to space environment: Part I. Impacts on aluminium targets

During the last three decades a wide variety of surfaces have been brought back to Earth after being exposed to space environment. The impact features found on these surfaces are used to evaluate the damages caused to spacecraft and can give clues to the characteristics of the orbital debris and meteoroids that created them. In order to derive more precisely the particle parameters and to improve the analysis of projectile remnants, we have performed an extensive analysis of craters caused by the impact of high velocity particles on thick ductile targets, using a micro-particle accelerator. We show that from the geometry of the craters and from the analysis of the remnants it is possible to derive the main characteristics of the projectiles. In particular, using up-to-date instrumentation, scanning electron microscope (SEM) and Energy Dispersive X-ray (EDX) spectrometer, we found that even small residues inside craters can be identified. However, this study shows that a velocity resolution better than 1 km/s would be appropriate to obtain a fair calibration of the impact processes on a ductile target. This would allow to decipher with precision impact features on ductile surfaces exposed to space environment.     

Study of singular surfaces of systems of unsupported gyrodynes by the parameter continuation method

A system of two-degree-of-freedom force gyroscopes (gyrodynes) is considered to be used for spacecraft attitude control. Possible values of its total angular momentum form some finite region P in the frame of reference rigidly connected with the spacecraft. Near the boundary of this region and singular surfaces located inside it the control of the angular momentum is complicated or impossible. The program angular momentum of the gyrodynes, realizing the law of variation of the spacecraft orientation, should lie inside P and outside some singular surfaces, and due to this fact the boundary and internal singular surfaces should be studied. This work is dedicated to the numerical construction of region P and its internal singular surfaces by the method of parameter continuation. Using the results by E.N. Tokar’ we formalize sufficient conditions which in some cases allow one to determine the type of the singular surface. As an example, a system of six gyrodynes is considered, for which the regions of variations of the intrinsic angular momentum and singular surfaces are constructed. The possibilities of the system are demonstrated for the case when one gyrodyne fails.     

原子氧环境效应的地面模拟技术

系统论述了原子氧和航天器表面常用聚合物材料反应的微观机理,并从宏观角度对这些材料的性能进行了评估。同时也总结了国外在原子氧防护技术研究方面所取得的最新成果。