一种新型的内置式永磁同步电机无位置传感器控制策略

针对内置式永磁同步电机(IPMSM)在低速域运行时模型参考自适应观测器对电机参数变化敏感、位置检测精度低以及鲁棒性差等缺点,提出了通过利用电机本体的参考模型和相应可调模型的差值构造滑模面,取代了传统模型参考自适应观测器中采用PI调节器作为自适应机构的做法,并且采用模糊控制器自适应调整滑模增益以抑制滑模运动的抖振。在MATLAB/Simulink环境下搭建了仿真模型。仿真表明:在外部扰动以及电机参数变化时,估计转速和转子位置均能跟踪到实际的转速和转子位置。     

基于RBF神经网络的液压位置伺服系统故障诊断

针对液压系统的非线性、时变、流固耦合的特点,提出双级径向基函数(Radial Basis Function,RBF)神经网络模型实现液压伺服系统故障检测与定位.采用第1级RBF网络作为液压伺服系统的故障检测滤波器,通过实际系统与RBF观测器输出的残差实现液压伺服系统故障检测.利用第1级RBF观测器的输出残差和网络结构参数,应用第2级RBF网络实现液压伺服系统典型故障定位.针对K均值聚类算法收敛速度慢的缺点,提出了改进K均值聚类算法和学习速率自适应调整算法,利用网络优化结构参数和学习率,加快神经网络收敛速度,减少运算量.实验结果表明,利用双级RBF神经网络能够有效地检测出液压位置伺服系统的故障,并能实现系统的故障定位.     

Robust speed sensorless induction motor drive

A speed sensorless induction motor (IM) drive with robust control characteristics is introduced. First, a speed observation system, which is insensitive to the variations of motor parameters, is derived based on the concept of sliding mode. Next, an integral-proportional (IP) speed controller using the estimated speed signal is designed to stabilize the speed loop. Then, to preserve the robust control performance under parameter variations and external load disturbance, an adaptive uncertainty observer with feedforward control is proposed. The adaptive uncertainty observer is implemented to estimate the lump of uncertainty of the controlled plant. To increase the accuracy of the estimated values, the speed observation system is implemented using a digital signal processor (DSP) with a high sampling rate     

感应电机全阶状态观测器及其无源性转速控制

为了实现感应电机的高动态调速性能,针对电机的非线性本质,提出了一种基于全阶状态观测器及其转速自适应估算的感应电机无源性转速控制方案。在基于感应电机无源性与稳定性分析的基础上,设计了渐近稳定转矩跟踪无源性控制器。针对无源控制律所需转子电流难以观测的问题,提出了一种旋转坐标系下以转子电流和转子磁链为状态变量的全阶状态观测器,并应用该观测器对转速进行估算,实现了感应电机无速度传感器的无源性转速控制。仿真结果表明该控制方法易于实现,采用全阶观测器观测转子电流值和估算转速值更为准确,显著提高了感应电机的动静态性能。     

考虑系统扰动的永磁同步电机复合控制策略

提出一种结合滑模速度控制和扩展滑模扰动观测器的永磁同步电机复合控制策略。滑模速度控制采用新型趋近律设计,扩展滑模扰动观测器对系统内部参数摄动以及外部负载干扰进行准确估计。所设计的复合控制器通过系统扰动估计环节对控制系统中的综合扰动项进行实时估计,用以对速度控制环节进行前馈补偿,实现控制系统自抗扰控制。试验结果验证了所提出控制策略的有效性和可行性。     

异步电机无速度传感器带速重投策略

在异步电机转速自适应全阶观测器无速度传感器控制方法的基础上,提出了一种基于波波夫稳定性理论的带速重投策略。该策略能够反映出转速估计值与实际值之间的误差关系,并通过自中心向两侧检索的方法使得转速估计值快速地向实际值收敛。采用了一种预励磁方案来达到减小带速重投过程中电流冲击的目的。仿真结果证明了所提策略的准确性和有效性。     

检测传感器故障的鲁棒观测器

介绍一种在系统参数变化情况下进行故障检测的观测器。对观测器采用特征值、特征向量进行联合配置的算法 ,并对估计误差设计奇偶空间 ,使各传感器的故障在奇偶空间中被解耦分离 ,因而可用一个观测器检测与分离多路故障传感器 ,实现了故障检测的鲁棒性     

THE ROBUST OBSERVER FOR FAULTDETECTION OF THE SENSOR

ＴＨＥＲＯＢＵＳＴＯＢＳＥＲＶＥＲＦＯＲＦＡＵＬＴＤＥＴＥＣＴＩＯＮＯＦＴＨＥＳＥＮＳＯＲＷａｎｇＳｈｅｎｇｙｕａｎ（Ｆａｃｕｌｔｙ３０１，ＢｅｉｊｉｎｇＵｎｉｖｅｒｓｉｔｙｏｆＡｅｒｏｎａｕｔｉｃｓａｎｄＡｓｔｒｏｎａｕｔｉｃｓ，Ｂｅｉｊｉｎｇ，Ｃ...     

Simultaneous state and actuator fault estimation for satellite attitude control systems

In this paper, a new nonlinear augmented observer is proposed and applied to satellite attitude control systems. The observer can estimate system state and actuator fault simultaneously. It can enhance the performances of rapidly-varying faults estimation. Only original system matrices are adopted in the parameter design. The considered faults can be unbounded, and the proposed augmented observer can estimate a large class of faults. Systems without disturbances and the fault whose finite times derivatives are zero piecewise are initially considered, followed by a discussion of a general situation where the system is subject to disturbances and the finite times derivatives of the faults are not null but bounded. For the considered nonlinear system, convergence conditions of the observer are provided and the stability analysis is performed using Lyapunov direct method. Then a feasible algorithm is explored to compute the observer parameters using linear matrix inequalities (LMIs). Finally, the effectiveness of the proposed approach is illustrated by considering an example of a closed-loop satellite attitude control system. The simulation results show satisfactory perfor-mance in estimating states and actuator faults. It also shows that multiple faults can be estimated successfully.     

故障诊断的神经网络观测器法

以神经网络的自学习代替故障诊断观测器法中的解析计算,提出了一种新的故障诊断方法,从而解决了具有模型不确定性系统的故障诊断问题。对某型航空发动机控制系统传感器故障进行了仿真研究,该方法不仅具有传统观测器法报警及时准确、易于实现容错控制的优点,又不需要获得系统精确的数学模型,对具有模型不确定性系统的故障诊断与容错很有效     

基于自适应滑模观测器的航空发动机故障诊断

为解决现有航空发动机基于模型的在线故障诊断方法存在对模型精度要求高等的问题,利用滑模方法设计一种自适应滑模观测器对航空发动机进行在线故障重构、诊断与隔离。对传感器故障和执行机构故障分别设计了重构算法,针对两者重构故障的特点提出了判断逻辑,讨论了设计参数对于观测效果与抖振的影响。 Matlab/Simulink仿真结果显示,重构的故障与实际故障基本吻合,对故障的诊断、隔离、定位具有良好效果,并对环境不确定性具有优良的鲁棒性。     

Calculation of high-temperature insulation parameters and heat transfer behaviors of multilayer insulation by inverse problems method

In the present paper, a numerical model combining radiation and conduction for porous materials is developed based on the finite volume method. The model can be used to investigate high-temperature thermal insulations which are widely used in metallic thermal protection systems on reusable launch vehicles and high-temperature fuel cells. The effective thermal conductivities（ECTs） which are measured experimentally can hardly be used separately to analyze the heat transfer behaviors of conduction and radiation for high-temperature insulation. By fitting the effective thermal conductivities with experimental data, the equivalent radiation transmittance, absorptivity and reflectivity, as well as a linear function to describe the relationship between temperature and conductivity can be estimated by an inverse problems method. The deviation between the calculated and measured effective thermal conductivities is less than 4%. Using the material parameters so obtained for conduction and radiation, the heat transfer process in multilayer thermal insulation（MTI） is calculated and the deviation between the calculated and the measured transient temperatures at a certain depth in the multilayer thermal insulation is less than 6.5%.     

基于变增益扩张状态观测器的永磁同步电机转速环自抗扰控制器设计

线性扩张状态观测器(LESO)在观测初始阶段,系统状态量实际值与估计值误差较大。由于LESO高增益的影响,导致LESO在初始时刻的扰动估计输出出现很大的峰值,而且观测器增益越大,峰值现象越严重。针对上述问题,设计了一种变增益扩张状态观测器(TESO),其增益是一个时变函数,在初始时刻为较小的函数值,随着时间逐渐增大,直至趋于一个较大常数。利用李雅普诺夫变换和微分代数谱理论给出了参数整定公式。将线性自抗扰控制器(LADRC)中的扩张状态观测器替换为TESO,并将其应用于永磁同步电机转速控制中,计算机仿真和系统试验验证了该控制器设计的有效性。     

INS/GPS组合导航系统故障检测问题研究

提出了一种新的故障检测方案。该方案由卡尔曼滤波 ,得到新息序列 ,利用大数定律对新息序列的稳定性进行检验 ,来判别系统是否出现了故障。同时提出了故障状态下卡尔曼滤波的修正算法。数值仿真结果表明 ,该方法能有效地检测出 INS/GPS组合导航系统的故障 ,保证了 INS/GPS组合导航系统的安全性和可靠性     

Instrument Failure Detection in Partially Observable Systems

Instrument failure detection using the dedicated observer scheme (DOS) depends on partial state observability through each instrument which is monitored. For instrument fault detection by the DOS technique, a quantitative measure of partial state observability is established for each instrument and used to determine a necessary condition on the output structure of the system. This measure, called the internal redundancy of the instrument, indicates the complexity of the logic required for failure detection, and it also indicates where some hardware redundancy can be introduced into the system to improve the fault detection capability of the DOS. The principles developed are applied to a simulation of the pitch axis autopilot of the A7 jet aircraft.     

车用液冷机壳电机定子绕组热性能直接设计法

电动汽车驱动电机极力追求高密度轻量小型化,不断推进电机的冷却散热与热传导技术的进步与发展。为此,开展车用驱动电机的电-磁-热一体化设计方法研究,通过构建一种工程化定子热路模型提出了定子绕组热性能直接设计法及其关键热参数,并直接融入电磁设计中,强化热性能设计的同时也弥补了传统电磁设计热负荷AJ值评估热性能的缺陷。通过快速评估电机的热传导能力和绕组温升,可评估比较不同设计方案的热性能,得到电-磁-热一体化设计的最佳解决方案,从而提升电机持续运行的输出转矩。采用定子绕组热性能直接设计法,改进设计了一台液冷机壳车用永磁同步驱动电机样机,显著降低了定子绕组温升。样机温升试验验证了定子绕组热性能直接设计法及其关键热参数评估热性能的有效性。     

Control synthesis for an unmanned helicopter with time-delay under uncertain external disturbances

This paper presents the controller synthesis for an unmanned helicopter with minimum initial information about the parameters of its mathematical model with time-delays of measured and control signals. The unknown parameters, wind disturbances, and system nonlinearity are considered as external disturbances that are estimated using a multi-gap observer. The estimates obtained are used in the control law to improve the stability rate for flight regimes.     

无轴承异步电机的自抗扰控制策略

针对无轴承异步电机(BLIM)的逆系统解耦控制性能受负载和参数变化影响的问题,在转子磁链定向逆系统解耦控制的基础上,采用自抗扰控制器(ADRC)替换经典的PID控制器,将BLIM模型中的交叉耦合项、本体参数变化和负载视为“扰动”,统一用ADRC的扩张状态观测器(ESO)估测,非线性状态误差反馈控制器(NLSEF)进行补偿。仿真结果表明:采用了ADRC,系统具有较好的动态解耦控制性能;同时,对电机参数和负载变化具有更好的鲁棒性。     

Thermal state calculation of chamber in small thrust liquid rocket engine for steady state pulsed mode

This paper presents a method of thermal state calculation of combustion chamber in small thrust liquid rocket engine. The goal is to predict the thermal state of chamber wall by using basic parameters of engine: thrust level, propellants, chamber pressure, injection pattern, film cooling parameters, material of wall and their coating, etc. The difficulties in modeling the startup and shutdown processes of thrusters lie in the fact that there are the conjugated physical processes occurring at various parameters for non-design conditions. A mathematical model to predict the thermal state of the combustion chamber for different engine operation modes is developed. To simulate the startup and shutdown processes, a quasi-steady approach is applied by replacing the transient process with time-variant operating parameters of steady-state processes. The mathematical model is based on several principles and data commonly used for heat transfer modeling: geometry of flow part, gas dynamics of flow, thermodynamics of propellants and combustion spices, convective and radiation heat flows, conjugated heat transfer between hot gas and wall, and transient approach for calculation of thermal state of construction. Calculations of the thermal state of the combustion chamber in single-turn-on mode show good convergence with the experimental results. The results of pulsed modes indicate a large temperature gradient on the internal wall surface of the chamber between pulses and the thermal state of the wall strongly depends on the pulse duration and the interval.     

基于GRU的仪表着陆系统故障预测方法研究

故障预测技术在保障仪表着陆系统的可靠运行、提高空管效能等方面具有重要应用价值。结合仪表着陆系统运行特征和实际运行维护工作,提出一种基于GRU 的仪表着陆系统故障预测方法。以航向信标为研究对象,在分析其监控参数与设备运行状态之间的关系后,将监控参数作为故障特征参数;根据监控参数时间步长、时变性特征显著的特点,采用GRU 预测监控参数的未来变化趋势;根据监控参数的隶属函数计算出参数未来时刻可能发生“故障”的概率,实现对航向信标故障的预测。结果表明：基于GRU 的预测方法的相对预测精度在95% 以上。