首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
民用飞机维修性参数选取和指标确定是维修性设计的基础工作之一,为了反映出民用飞机的维修性、运营费用和维修人力等方面的目标,需要选择合适的维修性参数并确定维修性指标。国产民用飞机由于缺少研制经验和设计资料,无法使用成熟方法进行维修性参数选取和指标确定,针对这一问题进行研究。结合民用飞机的设计特点阐述了民用飞机维修性参数的选取方法,通过综合权衡民用飞机设计中各影响因素和维修性参数有效性,从与维修时间相关、与维修工时相关、与维修成本相关的三类参数中选取适当的民用飞机维修性参数。针对民用飞机设计现状,明确维修性指标的确定依据和具有实用性的方法,以使民用飞机具有良好的维修性。解决了国产民用飞机维修性参数选取和指标确定工作无参考依据的问题,为民用飞机维修性参数选取和指标确定提供了一条可行途径。  相似文献   

2.
安全性是民用飞机设计及使用时必须考虑的首要问题,安全性指标要求将影响民机的设计、维修及使用。本文对比讨论了美国联邦适航条例FAR25.1309节及西欧适航条例JAR25.1309节对安全性指标及其评定的要求;较详细地分析了飞机及其系统安全性指标的确定与评定的原则及方法;最后,以FAR25.1309为例讨论了安全性指标及其评定要求对民机设计、维修及使用的影响。  相似文献   

3.
初始适航阶段的机务维修既要保证飞机合格审定试飞实施和安全,落实维修要求,实施维修作业,同时也要开展维修设计验证,并接受试航审定管理部门的监督检查。因此,对民机初始适航维修目标、任务及管理的内容和要求进行了初步探讨。  相似文献   

4.
本文提出了一种简单实用的维修定性指标评估方法。该方法要求维修人员尽早介入飞机研制过程,对维修性指标进行评分考核,建立起从客户端到制造商的信息反馈渠道,以便及早发现维修缺陷并进行设计更改。  相似文献   

5.
在装备设计时纳入人素工程设计要求,研究人为因素对装备使用与维修的影响,讨论了人为因素分析的目标与技术,重点进行了人为差错分析和安全性分析. 武器装备是一个复杂的人、机、环境系统,在装备设计时,若不考虑人的因素,不仅维修问题增多,而且系统的效能和战备均将降低.  相似文献   

6.
维修性预计方法运用现状及展望   总被引:2,自引:0,他引:2  
维修性预计也称维修性预测,它是根据历史经验和类似的维修性数据,对新的产品设计构想或已设计的结构方案,预测其在预定条件下进行维修时的维修性参数,以便了解设计满足维修性要求的程度.维修性预计参数应与规定的指标参数相一致.最经常预计的参数是平均修复时间,或最大修复时间,工时频率或预防维修时间等.预计的参数常常是系统级或设备级的.  相似文献   

7.
 针对目前军用飞机设计中无维修工作期(Maintenance-free Operating Periods, MFOP)指标无法分解和落实的问题,通过对基本可靠性、故障预测、系统重构和冗余设计等影响军用飞机MFOP实现的主要因素进行分析和数理建模,提出了一种军用飞机MFOP参数的分解流程和方法,为MFOP由使用参数(使用要求)向合同参数(设计要求)的分解提供初步的方法基础,能够为军用飞机的MFOP指标分析论证和基于MFOP的飞机可靠性设计工作提供一定的理论指导.  相似文献   

8.
以战备完好性为中心的维修管理   总被引:1,自引:1,他引:0  
阐述了以战备完好性为中心的维修管理的涵义 :在装备系统的全寿命中以系统工程的方法优化维修 ,确保装备具有良好的保障特性与保障系统 ,力争维修的高效 ,使能以最少的全寿命费用达到所要求的战备完好性。其要点包括 :确保装备具有良好的保障特性和保障系统 ,提出了于监控对装备进行健壮设计的同时 ,同步进行工艺与硬件设计、改装预案设计 ,贯彻以可靠性为中心的维修等。  相似文献   

9.
基于三维模型仿真平台,对某型发动机试验件典型航线可更换单元(LRU)进行虚拟维修仿真,通过可达性、可视性、维修姿态及操作空间分析,评估了目标LRU维修性水平,初步建立了基于虚拟维修仿真的民用航空发动机LRU维修性验证优化流程,基于该流程,针对后续发动机型号LRU维修性设计要求,持续优化外部管路维修性设计过程。  相似文献   

10.
民用航空维修工程具有显著的特殊性和职业特点。民用航空维修工程要求使飞机和机载设备保持其固有的可靠性,使飞机各系统功能正常。因而,不论是飞机哪个系统或哪个部位出现故障,均要求维修工程技术人员不仅能从理论上分析,更重要的是通过状态监控、事后维修或预防性维修快速准确地解决问题,以确保飞机安全正点。民用航空维修工程教育的目标就是培养系统工程型高级维修人才,要求毕业生既能掌握从机载设备的设计思想、结构和工作  相似文献   

11.
有翼高超声速再入飞行器气动设计难点问题   总被引:2,自引:1,他引:2  
杨勇  张辉  郑宏涛 《航空学报》2015,36(1):49-57
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。  相似文献   

12.
Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters   总被引:1,自引:0,他引:1  
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.  相似文献   

13.
范平  范玉青 《航空学报》2008,29(3):707-715
 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。  相似文献   

14.
ν-gap度量及其在飞行控制律评估中的应用   总被引:1,自引:0,他引:1  
刘林  纪多红  唐强 《航空学报》2007,28(4):930-934
 传统控制律评估方法主要用于单输入单输出(SISO)系统,且对模型参数摄动考虑不够全面,针对这些不足,研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上,给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算,提出ν-gap度量评估控制律的步骤。实例结果表明,该方法不仅克服了上述传统评估方法的缺陷,而且还有根据所求的各摄动影响情况忽略影响小的元素,以减少计算量及可以找到最坏情况下的参数摄动组合等优点。  相似文献   

15.
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.   相似文献   

16.
临近空间飞行器测控与信息传输系统频段选择   总被引:7,自引:0,他引:7  
柴霖 《航空学报》2008,29(4):1007-1012
 临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。  相似文献   

17.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展   总被引:3,自引:0,他引:3  
张堃元 《航空学报》2015,36(1):274-288
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。  相似文献   

18.
Integrated Entry Guidance for Reusable Launch Vehicle   总被引:2,自引:2,他引:0  
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.  相似文献   

19.
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.  相似文献   

20.
(高)超声速流动试验技术及研究进展   总被引:1,自引:1,他引:1  
易仕和  陈植  朱杨柱  何霖  武宇 《航空学报》2015,36(1):98-119
近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号