Ambiguity Removal When Using Burst Waveforms. Part II: Nonlinear Processing

An effective technique for removing range ambiguities (detections at ranges other than the true range of the object) arising when using a burst waveform is to transmit two bursts with different pulse repetition frequencies nearly simultaneously and then to process their outputs nonlinearly. This correspondence introduces two nonlinear processors which combine coincidence detection with either noncoherent multiplication or integration. It is shown that the combined false alarm and ambiguity removal performance of these nonlinear processors is superior to the performance of coincidence detection, noncoherent multiplication, or noncoherent integration when used separately.     

小束斑电子束脉冲轰击偏压电源的研制

为了获得一种性价比较高的电子束表面处理技术,采用定频调压电路,研制出一种新型偏压脉冲电源。这种电源由偏压主电路拓扑、偏压变压器和偏压整流滤波电路组成,其中偏压主电路由偏压基值发生电路和偏压脉冲发生电路组成。偏压基值发生电路控制偏压脉冲基值,偏压脉冲发生电路控制偏压脉冲频率和占空比。脉冲偏压电源的脉冲基值、脉冲频率、占空比均连续可调,相应实现脉冲束流的幅值、束流频率和占空比的调节。检测分析了脉冲偏压电源的输出电压波形,带载时的输出束流波形,并观察分析了电子束轰击后钨合金组织变化规律。结果表明所研制的脉冲偏压电源输出电压稳定、可调性好,能满足小束斑脉冲电子束轰击工艺的要求。     

Analysis of a PWM-resonant converter

When a parallel resonant tank is excited by a bipolar current pulse train a sinusoidal voltage develops across the tank whose amplitude depends on the duty cycle of the pulse train. An isolated secondary can be derived by applying the tank voltage to an isolation transformer whose magnetizing inductance acts as the resonant inductor of the tank circuit. A dc output voltage is obtained after rectification and filtering of the sinusoidal secondary voltage and regulation is achieved by controlling the duty cycle of the pulse train. The sinusoidal nature of the voltage across the isolation transformer alleviates some of the noise problem associated with parasitic capacitances of an isolation transformer when operated with square voltage waveform. In this work the dc and small-signal analysis of the converter is given and an equivalent small-signal circuit model is derived. Experimental results which confirm the validity of the model are presented.     

Slope Coding of Coherent Pulse-Burst Waveforms

Useful new properties are obtained with a coherent pulse-burst waveform if the FM slopes are allowed to change from pulse to pulse. A design feature using such a "slope-coded" waveform is the ability to transfer, in a controllable manner, ambiguity volume from the range ambiguity peaks to regions located between the peaks (in the frequency direction). Slope coding thus provides a useful mechanism for matching the waveform to the environment; i. e., it permits the signal designer to make some compromise between range ambiguity-peak heights and low-velocity clutter rejection.     

CW alternatives to the coherent pulse train-signals and processors

Continuous wave (CW) signals phase modulated by a periodic waveform, and their corresponding receivers, are discussed. The combined response in delay and Doppler is almost identical to the (ideal) response of the coherent pulse train. The receivers are matched to an integral number N of modulation periods of the transmitted signal. CW implies a duty cycle of 100%. However, the signal duration need not be longer than N+2 periods. The CW signals have the advantage that their peak power is equal to the average power. Their disadvantages are more complicated receiver processing and the need for two antennas     

Choice of Burst Number for Blind-Speed Avoidance

A common problem in radar system design is the choice of multiple PRF's to eliminate the blind speeds associated with coherent pulse bursts with uniform pulse spacing. This correspondence describes the procedure of selecting a set of PRF's in such a manner that the unambiguous Doppler achievable with the entire set is maximized. Based on this optimization of the set of PRF's, we determine how many PRF's the set should contain in order to minimize the required beam dwell time for a specified unambiguous Doppler.     

高温合金IN718上气膜冷却孔电火花加工试验

针对高温合金IN718上ø0.5mm气膜冷却孔的加工,采用煤油中旋转电极内冲液电火花成型加工方法,利用正交试验设计方法对试验进行设计分析,分析峰值电流、脉宽、占空比和冲液压强4个因素对材料去除率和电极相对损耗的影响,基于正交试验结果建立综合评分公式,选择最优加工参数.研究结果表明,峰值电流对材料去除率的影响最明显, 其次为冲液压强和占空比,脉宽对材料去除率的影响很小;峰值电流对电极相对损耗的影响最明显,其次为冲液压强,占空比和脉宽对电极相对损耗的影响很小;最优的加工参数峰值电流为8A、脉宽为130μs、占空比为0.35、冲液压强为5MPa,对该参数进行加工试验研究,与分析结果一致.      

脉冲吹气对无缝襟翼翼型气动性能的影响

只有采用足够小的能量输入,获取更大的空气动力收益后,主动流动控制才有可能在真实飞机上获得更广泛的应用。脉冲吹气比定常吹气所需能量更少,控制效果更好,在改善翼型气动性能上得到广泛的研究。数值模拟了脉冲频率、占空比、动量系数等参数对无缝襟翼翼型升阻特性的影响规律,研究表明,脉冲频率接近于涡脱落频率时增升效果最好,当脉冲频率小于涡脱落频率时,阻力增加,当脉冲频率为涡脱落频率2倍时,阻力减小最多;动量系数较小时,占空比越小,冲击效应越强,增升效果越好;动量系数小于临界动量系数时,脉冲吹气增升效果优于定常吹气,当动量系数大于临界动量系数时,脉冲吹气控制效果低于定常吹气。研究脉冲吹气参数对翼型性能的影响规律,对采用周期性激励增升减阻、舵面增效的飞行器设计具有一定参考意义。     

模型脉冲爆震火箭发动机可爆范围的实验研究

在采用电磁阀控制间歇式供应的脉冲爆震火箭发动机模型上,研究了燃料、氧化剂的喷射占空比、喷射及点火的时序对两相爆震波形成的影响,得出了在一定供应条件下的可爆范围,掌握了控制规律。分析了这些影响的实质在于混合物的当量比和有效混合程度。实验结果表明,燃料/氧化剂喷射占空比应尽可能接近,并保证爆震管的有效填充,在此条件下应尽可能保证喷射相位一致,以达到最好的混合效果。     

Variable Format Radar Receiver Using a SAW Convolver

A technique for receiving radar pulse trains is presented [which can be of a variable format in the sense that they vary from pulse to pulse]. The heart of the receiver is a sufrace ascoustic wave (SAW) convolver. In addition to prsenting experimental results for variable format waveform reception, it is shown that the convolver can easily generate ambiguity functions for virtually any waveform, and specific results for signals such as Barker codes and linear FM (chirp) waveforms are presented.     

Ambiguity Functions for Quadratic Phase-Coded Pulse Trains

The matched filter ambiguity function is presented for a burst waveform composed of repeated subbursts, each one of which consists of N pulses in which the phase is varied quadratically from pulse to pulse. The resulting ambiguity function exhibits small residual ambiguities along the delay axis separated by the reciprocal of the pulse repetition frequency (PRF). A cross-ambiguity function is derived which reduces these ambiguities to zero amplitude. A third cross-ambiguity function is presented for a receiver matched to a generalized Hamming weighted repeated quadratic burst. The location in the delay/Doppler plane of the waveform ambiguities for these waveforms is compared with that of an uncoded pulse burst.     

基于CPLD的多路脉冲序列信号检测器设计

用VHDL语言在CPLD器件上实现了一种多路脉冲序列信号检测器,能够用七段数码管实时显示各路已检测出序列信号数目,电路各摸块用VHDL语言来描述。文章介绍了仿真信号的形成原理和电路设计方法,并给出了部分电路和仿真波形。整个多路脉冲序列信号检测器设计在一块CPLD芯片上,与其他方法设计的序列信号检测器相比,具有体积小、可靠性高、功牦低的特点。由于采用模块化的设计,对功能的修改和增加只要修改VHDL源程序,而不必更改硬件电路,从而实现数字系统硬件的软件化。     

测量波形占空比的一种新方法

在实践的基础上,本文扼要地介绍了用发光数码表直接读取波形占空比百分数(或频率值)的一种新方法,它简便易行,具有一定实用价值。     

颗粒增强金属基纳米复合材料脉冲电沉积制备研究

采用脉冲电沉积,在普通碳钢表面制备了Ni-W-P／CeO2-SiO2颗粒增强金属基纳米复合材料,研究了脉冲峰值电流密度和脉冲占空比对电沉积过程的影响,采用纳米颗粒的质量百分含量、沉积速率、显微硬度和表面形貌进行表征。结果表明：增加脉冲峰值电流密度或脉冲占空比,Ni—W—P基质金属晶粒细化,CeO2和SiO2纳米颗粒的质量百分含量提高。当脉冲频率为1000Hz,脉冲峰值电流密度和脉冲占空比分别为40A／dm^2和50％时,沉积速率最快（56．24μm／h）,显微硬度最高（712Hv）。此时,Ni—W—P基质金属轮廓清晰,晶粒细小而均匀,CeO2和SiO2纳米颗粒以弥散态均匀分散在基质金属中。     

宽带信号去斜脉冲压缩处理方法的研究

宽带信号广泛应用于雷达、导航和卫星通讯等领域。宽带信号的传统接收处理方法主要是采用匹配滤波或子带分割技术。本文用去斜脉冲压缩处理方法处理宽带信号,给出了具体的实现结构和改进措施,分析了如何选择系统的信号采样频率,同时还给出了脉压波形的仿真结果及性能分析。实验表明:对中心频率为9.5GHz、带宽1.3GHz、脉冲宽度30μs的宽带线性调频信号,采用该方法处理只需90MHz采样数据率,大大降低了数据采集的难度。     

相控阵主动雷达导引头波形策略

针对高脉冲重复频率脉冲多普勒(HPRF-PD)体制的相控阵主动雷达导引头中存在的距离遮挡问题,设计了一种新的波形选择策略。首先,利用提出的脉冲重复频率(PRF)波形选择策略,离线计算得到距离对应PRF的波形查找表。然后,通过叉积自动频率控制环路滤波(CPAFCLF)算法预估下个相参处理间隔(CPI)导引头与目标间的径向相对速度,并联合提出的基于Sage-Husa带有速度预测的自适应"当前"统计模型(SH-ACSMVP)算法得到的距离跟踪值,获得下个CPI的距离预测值。在跟踪机动目标场景中,相比于"当前"统计(CS)模型跟踪算法及基于"当前"统计模型的自适应无迹卡尔曼滤波(CAUKF)算法,本文算法得到的距离预测误差更小,误差收敛速度更快。根据此距离预测值从波形查找表中选择波形发射,作为下个CPI的发射波形,实现后续跟踪阶段的抗距离遮挡,提高目标跟踪性能。仿真结果表明了本文所设计波形选择策略的正确性及有效性。     

多旋翼无人机的电机关键参数确定方法

通过直流电动机模型推导出PWM波的占空比与电机转速的模型,根据功率守恒方程和上述模型得出电机内阻、反电动势、自身力矩系数和螺旋翼的升力系数的计算方法.通过试验的方法测试安装有螺旋翼电动机的输入电流有效值、占空比和转速,并计算电动机的参数,最后带入到占空比与电机转速的关系模型中,验证以上推导出的模型和计算方法的合理性.结果表明模型的相对误差在3％左右.     

等离子体气动激励抑制机翼失速分离的实验

进行了等离子体气动激励抑制机翼失速分离的风洞实验,研究了等离子体气动激励频率、电压、占空比和激励位置等对流动控制效果的影响.研究表明:在来流速度35m/s时,等离子体气动激励可以有效地抑制机翼大攻角下吸力面的流动分离,将机翼临界失速迎角由17°提高到19°;施加激励后,机翼最大升力系数提高了9.45%,阻力系数减小20.9%;激励频率在200Hz时,控制效果最好,对应的量纲一激励频率为1;迎角越大,流动分离越严重,需要更大的激励电压才能够有效抑制流动分离;最佳激励位置在流动分离起始点的前缘;在流动控制效果相当时,减小占空比可以降低能耗.      

激光器匹配驱动的色散渐变线分析

论述了采用渐变线阻抗变换器对半导体激光器进行匹配驱动时,当考虑渐变线色散影响情况的分析。给出了色散影响的概念、时域的分析计算方法及对三角形、指数形及切比雪夫渐变线的计算结果和分析。     

一种步进频率信号认知雷达波形优化设计方法

认知雷达常用于完成探测、跟踪、成像及识别等多重任务,为提高其综合性能,需兼顾多方面因素研究其波形优化设计问题。基于此,提出一种基于压缩感知（CS）RIPless准则的步进频率信号认知雷达波形优化设计方法。首先,建立了目标回波信号稀疏模型,分析了其与发射信号模糊函数之间的关系。其次,根据模型中观测矩阵的构造,基于RIPless准则,将波形设计问题转化为概率分布的互相干参数及其协方差矩阵的条件数的优化问题,从而通过自适应寻优算法,获得优化的步进频率信号脉冲重复时间间隔序列和子脉冲频率序列。相较于传统方法,所提方法在信号发射与接收之间形成了信息实时反馈和信号优化重构的闭环,在高概率准确重构目标径向一维距离像的同时,也实现了发射信号模糊函数的优化。最后,仿真计算验证了所提方法的有效性。