无人机电磁弹射技术研究

与现有的各种无人机发射方式相比,无人机电磁弹射方式具有更多的优点,能更好地提高无人机发射效率。通过原理性分析以及导轨起飞运动学分析,对无人机电磁弹射技术进行了可行性研究。高功率脉冲电源系统释放强直电流后,电流经导轨与电枢形成回路,在回路间产生强磁场,无人机受电磁推力作用沿导轨高速运动。最后通过实例的计算数据比较,确定无人机电磁弹射技术是可行的且优点明显。     

应用电磁弹射器的舰载机起飞性能分析

针对应用电磁弹射器的舰载机弹射起飞过程,综合考虑了电磁弹射器的推力、舰载机前起落架突伸力和载舰的运动,建立了舰载机弹射起飞的数学模型,并据此,分析了上述各种因素对舰载机弹射起飞安全性的影响,计算得到在满足舰载机弹射起飞安全准则的条件下,各种起飞因素应该满足的适应范围。研究分析表明：在风浪较大的恶劣天气条件下,通过适当地增加电磁弹射器的电磁推力和前起落架的突伸力,可以有效抑制舰载机的航迹下沉现象,确保舰载机的安全起飞过程。     

舰载机偏中心定位弹射起飞弹射杆载荷分析

 考虑舰载机偏中心定位,建立了六自由度弹射起飞动力学模型,对偏中心弹射过程中弹射杆受载情况进行了分析计算,讨论了初始偏心距离和起飞重量对弹射杆载荷的影响,并详细论述了其动力学成因。研究结果表明：飞机的滚转运动是导致弹射杆承受较大弯矩和扭矩的主要原因;弹射杆弯矩和扭矩随初始偏心距离的增大而迅速增大,但其轴向拉力受初始偏心距离影响较小;在弹射滑跑初始阶段,弹射杆的轴向拉力、弯矩以及扭矩随起飞重量的减小而增大,而在弹射滑跑后期,弹射杆所受载荷则随起飞重量的减小而减小。     

类X-43A飞行器高超声速分离仿真

高超声速飞行器级间分离过程广泛存在于军事和航空航天应用中。为了对该过程中气动干扰和各分离参数的影响有更加深入认识,以类X-43A飞行器为研究对象,采用网格变形/局部网格重构的方法对其进行仿真研究。详细分析了高超分离过程中典型的流场结构,尤其是飞行器和助推器之间的级间干扰;另外,重点讨论了初始攻角、弹射力对分离过程中飞行器和助推器的轴向/法向相对距离、气动力以及飞行器攻角的影响规律。结果表明：级间分离过程受到涡流和激波的双重干扰;攻角对飞行器和助推器法向相对距离影响较大,小攻角或负攻角更有助于二者分离;弹射力对轴向相对距离影响显著,较大的弹射力能够使飞行器较快脱离级间干扰区,达到安全的分离距离。     

舰载机斜板滑跃起飞情况地面载荷

设置舰艏斜板以减少舰载机起飞滑跑距离、降低甲板风要求,从而实现无弹射系统情况下的短距起飞作业,这已在一些“蓝水”海军强国的航空母舰上得到了多年应用。给定航母起飞甲板长度和斜板曲线构型,飞机能否成功滑跃起飞取决于它的气动特性、最大起飞质量、发动机推力、出口速度和起落架强度。 本文提出了一种舰载机斜板滑跃起飞情况地面载荷的计算方法,也建立了完整的斜板曲线方程（曲线已经过飞机适配性优化）。文中还应用本方法计算了某双座多用途舰载教练机的滑跃起飞地面载荷。     

舰载飞机弹射起飞安全评价准则研究

舰载机安全地从航母上起飞是舰载机设计和使用的关键指标之一,通过对国外舰载机弹射起飞规范、资料的研究,结合陆基飞机起飞规范的要求,分析了舰载机弹射安全起飞需要满足的各项指标要求,从飞行性能、飞行品质角度提出了舰载机弹射起飞安全评价准则。该准则可为舰载机设计和使用提供参考。     

舰载飞机弹射起飞性能和影响因素分析

本文通过舰载飞机弹射起飞动力学的研究,并根据弹射起飞的过程和要求,提出了确定弹射起飞参数(弹射力、发动机推力和平尾偏角)的计算方法。文中对舰载机的弹射起飞进行了仿真计算。最后讨论了飞机的起飞质量,发动机推力、起飞迎角、襟翼偏角和甲板风航迹等对弹射起飞性能的影响.     

舰载飞机弹射起飞的机舰参数适配特性

舰载飞机与航母之间的参数适配特性是弹射起飞总体方案设计阶段的关键问题之一。针对舰面起飞的复杂环境,建立了舰载飞机弹射起飞的数学仿真模型。在此基础上,分析了各主要机舰参数对弹射起飞安全性的影响,并计算得到满足弹射起飞安全准则的主要机舰参数的适配值集合。研究结果表明:在弹射起飞过程中,增加弹射能量、前起落架突伸力和升降舵预置偏角均可抑制航迹下沉;在适配值集合内,随着弹射能量的增加,升降舵预置偏角的适配范围增大,前起落架突伸力的影响减小。     

舰载机弹射起飞动力学仿真与安全边界评估

为了研究影响舰载机弹射起飞安全性的因素,在舰载机弹射起飞动力学模型的基础上,设计了标准起飞航迹并进行了数值仿真。分别对航母、飞机、环境等参数对安全起飞的影响规律进行了仿真研究,然后对多种参数的组合影响进行了仿真分析,最终获得了安全起飞的边界参数。     

国外飞机牵引技术标准浅析

一、概述 飞机地面牵引技术是一个涉及飞机、牵引装置、牵引动力设备及机场条件等多种因素的综合技术。在当前,由于飞机运载量加大,地而滑行距离加长和机场对飞机迅速起飞的要     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.