一种稀疏阵列下的二维DOA估计方法

研究了稀疏阵列下二维波达方向（DOA）的估计问题,提出一种基于不动点迭代的空间谱估计（FPC-MUSIC）算法。首先建立基于矩阵填充的DOA估计信号模型,并验证该信号模型满足零空间性质（NSP）,其次通过不动点迭代算法将稀疏阵列信号恢复为完整信号,最后利用恢复信号估计二维DOA。该算法可在稀疏阵列下大幅度降低谱估计平均副瓣,在大幅度降低阵元数的同时具有较高的估计精度。计算机仿真表明：FPC-MUSIC算法可在稀疏阵列下准确估计二维DOA,验证了该算法的有效性和优越性。     

运动单阵元被动合成阵列波达方向估计

 提出了一种运动单阵元被动合成阵列波达方向(DOA)估计算法。该算法基于被动合成阵列(PSA)的概念,结合空间谱估计的思想构建了运动单阵元被动合成阵列模型,通过多次不同速度合成阵列过程实现对信号DOA的无模糊估计。通过对单次匀速合成阵列过程进行分析得到,在假设信号频率已知条件下,合成阵列算法能够达到与同孔径实阵列多重信号分类（MUSIC）算法相当的DOA估计性能。仿真验证了被动合成阵列与同孔径实阵列的渐近等效性及算法的有效性。     

基于空域稀疏性的宽带DOA估计

利用宽带阵列接收信号的空域稀疏性,将宽带信号的波达方向(DOA)估计转化为一个稀疏信号重构的问题,提出了一种新的宽带信号DOA估计算法。该算法将宽带信号分解为多个子带信号,联合利用多个子带信号的空域稀疏性进行重构。它是对用于稀疏重构的标准的稀疏贝叶斯学习算法的推广,可适用于多冗余字典的信号模型。另外,通过对多快拍的阵列接收信号进行奇异值分解(SVD),提取信号子空间作为算法的输入数据,可以在有效减少运算复杂度的同时,提高对噪声的稳健性。与传统的宽带阵列DOA估计方法相比,该算法能够用于低信噪比、快拍有限和信源相关性较高的场合,同时算法的性能对信源个数的估计值不太敏感。仿真实验表明,该算法相对现有的基于子空间类的方法,具有更好的DOA估计性能。     

未知互耦条件下混合信号波达方向估计

阵列天线互耦对导向矢量的扰动以及信号相干性对数据协方差矩阵造成的秩损,使得基于子空间正交性原理的超分辨波达方向估计(Direction-of-Arrival,DOA)算法性能恶化,甚至失效。针对这一问题,提出一种在相干与非相干信号混合状态下无需阵列互耦补偿的特征矢量平滑DOA估计算法。该算法对部分阵元接收数据的协方差矩阵特征分解,将得到的特征矢量平滑处理后构造等效协方差矩阵,抑制阵列互耦影响的同时完成混合信号DOA估计。在阵列互耦和信号相干性均未知的条件下,正确估计了信号DOA,无需互耦参数估计或补偿。计算机仿真结果验证了算法的有效性。     

基于压缩感知的频率和DOA联合估计算法

波达方向（DOA）估计是阵列信号处理的一个重要问题,针对信号的DOA估计问题,本文基于压缩感知理论,提出了一种新的频率和角度联合估计算法。首先利用方向波数的空间稀疏性,建立过完备稀疏字典,然后利用压缩采样阵列结构通过求解最优化问题得到方向波数的高分辨估计,最后利用最优空域滤波实现信号到达角度和频率的配对。相对于传统算法,该算法能够实现多信号DOA的高分辨估计,且经过压缩采样后降低了运算量,仿真验证了该算法的正确性与有效性。     

线性极化敏感阵列的极化平滑算法及相干源参数估计

 研究了基于极化敏感阵列的相干信号参数估计问题。首先,提出一种利用均匀线性极化敏感阵列的新型极化平滑算法(ULAPSA),其能够处理更多相干信号的参数估计,且具有更小的计算量。然后,基于ULAPSA给出了波达方向（DOA）和极化参数估计的两种方法：第1种方法利用角度搜索得到信号的DOA估计,适应任何多分量的电磁矢量传感器阵列;第2种方法结合传播算子算法,无需奇异值分解和角度搜索,能够同时估计信号的DOA和极化参数。该方法适应完备的电磁矢量传感器、三偶极子或三磁环构成的矢量传感器。最后,通过仿真实验比较和分析了所提算法的性能。     

一种适用于任意阵列的极化和二维DOA联合估计算法

提出了一种适用于任意阵列的极化和二维DOA联合估计算法。该算法基于信号空时二维结构特征,利用空域采样和时域采样构造时空矩阵,通过DOA矩阵方法进行极化和二维DOA参数估计,不需要二维谱峰搜索,计算量小。仿真实验证明了算法的有效性。     

利用分数低阶空时矩阵进行冲击噪声环境下的DOA估计

研究冲击噪声环境下的信号DOA估计问题。在对称α稳定(SαS: Symmetric α-stable)分布冲击噪声假设下,定义了一个阵列接收数据的广义分数低阶空时矩阵。理论分析表明,对广义分数低阶空时矩阵进行奇异值分解可获得噪声子空间估计。与信号空间DOA估计技术相结合,提出一种新的基于信号空间分解的DOA估计算法。该算法在低信噪比下对强冲击噪声具有更好的抑制作用。计算机仿真证明了算法的有效性。     

双L型阵列DOA估计的PM算法的性能分析与改进

 双L型阵列天线的二维信号来向（DOA）估计采用传播算子法（PM），运算简单、计算量小。但对于非对称的双L型阵列天线，其中阵元数目少的均匀直线阵会引起较大的DOA估计误差。为此进行PM算法的性能分析与误差讨论，在单个信号源的前提下提出一种改进的PM算法。理论分析与计算机仿真结果均表明，该改进的PM算法保持了PM本身计算量小的优点，能够实现实时二维DOA估计。同时提高了测角精度，降低了方差，且对双L型阵列的使用更具普遍性。     

存在阵列模型误差情况下的宽带DOA估计

 针对工程应用中存在阵列模型误差的任意形状天线阵列的宽带波达方向（DOA）估计问题,提出一种基于信号分离的相关域宽带松弛（RELAX）算法。此算法利用具有记忆与遗忘特征的矩阵算子的投影机理对入射信号进行有效的分离,因此对一定范围内的阵列模型误差较之基于子空间理论的传统宽带测向算法具有较好的鲁棒性与良好的工程应用前景。分析并证明了此算法的信号分离机理及此算法对阵列模型误差稳健的原理。理论分析与仿真结果均表明存在阵列模型误差时此算法宽带DOA估计的有效性和稳健性。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.