射流涡发生器对激波边界层作用诱导的流体分离控制大涡模拟研究

为了研究射流涡发生器对激波边界层作用所诱导的流动分离控制机理及其流场特性,基于大涡模拟(Large eddy simulation)方法和高阶TCD/WENO混合格式,对来流马赫数Ma=2.5情况下,平板上射流涡发生器对激波与边界层相互作用所诱导流场进行了数值模拟。结果表明,射流涡发生器对激波边界层的流体分离有一定的抑制作用,与无控制情况相比,射流作用下进出口总压恢复系数由85.9%提高到94.6%。射流尾涡主要集中于一环状区域内,在该区域内,入射激波与马蹄涡、桶形激波上方的涡管以及剪切涡相互作用,导致整体尾流被激波往下压缩。同时在激波的压缩下,各涡之间相互缠绕、挤压合并,形成多个流向小涡结构,将边界层外的高速流体卷入边界层内,从而增加边界层底层能量,达到抑制流动分离的目的。     

MVG控制斜激波/湍流边界层干涉的大涡模拟

采用浸没边界法(IBM)对带有微型涡发生器(MVG)控制器的激波/湍流边界层干涉流动进行了大涡模拟(LES)。以来流马赫数为2.3的斜激波(由平板上方8°楔产生)为基本流动入射平板湍流边界层,通过在干涉区前布置MVG阵列来控制激波诱导的边界层分离。采用浸没边界法处理MVG的复杂几何,分析了MVG尾迹区平均流速度剖面,雷诺应力,瞬态旋涡结构。结果表明:时均流场显示MVG尾迹区存在一对对转的主流向涡,流向涡加剧了边界内的动量交换从而增加了边界层抗分离能力,而瞬态流场则反映出MVG尾迹区的剪切层由于Kelvin-Helmholtz(K-H)不稳定性会卷起为一列展向旋涡。     

压气机叶栅的涡发生器流动控制研究

本文通过实验和数值模拟,研究了涡发生器对压气机端壁角区流动及损失的影响,在研究中利用流向涡加强端壁角区内的低能流体与主流高能流体之间的交流,从而达到抑制分离、降低损失的目的.通过对实验与计算结果进行定性和定量分析,比较了不同条件的涡发生器作用下的叶栅性能影响.     

流向涡与涡轮叶栅二次流相互作用研究

研究有效的流动控制手段,降低涡轮内部二次损失,对于小展弦比涡轮的气动设计具有重要意义。利用涡发生器在叶栅入口前产生流向涡,通过试验和数值方法探讨这种基于旋涡相互作用的流动控制方法对涡轮平面叶栅二次流动的作用效果,并对不同流向涡情况做对比分析。结果表明：流向涡对涡轮叶栅内部流动会产生较为显著的影响,从而影响叶栅的性能,当所产生流向涡强度和位置较为合理时,有可能通过流向涡与二次流的相互作用达到较大幅度降低二次流损失的目的。     

被动射流旋涡对高速扩压叶栅气动性能的影响

提出了一种利用压力面与吸力面间压差产生射流旋涡的被动流动控制技术以改善压气机叶栅的气动性能,在进口马赫数Ma=0.67的高速扩压叶栅上验证了其有效性。结果表明,射流旋涡可有效增强吸力面附面层与主流间的能量交换,改变下游壁面涡的结构和尺寸,推迟流动分离,减小角区损失。当射流距分离线或端壁较近时,当地较厚的附面层使得旋涡上洗区的掺混损失增加;而射流距分离线或端壁过远时均会减弱下洗区能量注入对角区低能流体的影响;指向端壁的射流会增加壁面涡强度,而沿远离端壁方向过大的偏角则会减弱射流旋涡强度,从而减弱其控制效果。当射流轴向距叶片前缘xj/cx=40%、沿叶高距端壁h/H=15%、射流偏角β=60°时,其改善栅内流动的效果最佳,总压损失减小可达5.2%,而射流流量仅相当于主流的0.27‰。     

旋涡发生器对叶片根部马蹄涡的影响

针对简化了的叶片-平板结构,在叶片上游平板上的某位置布置旋涡发生器影响马蹄涡.数值模拟了不同高度旋涡发生器作用下的角区湍流流动.结果表明:任何一种旋涡发生器都能不同程度地削弱马蹄涡系,高度为2mm的旋涡发生器能使这种削弱作用达到最大;另外,随着高度的增加,叶片两侧的涡腿有向叶片聚拢的趋势.提出的方法无需额外消耗能量,为一种被动的控制手段,有很大的实际应用前景.布置旋涡发生器的控制方法简单实用,工程中采用该法是不错的一种选择.      

涡流发生器控制喷水推进器进水管流动分离的数值研究

为抑制某型喷水推进平入口进水管低进速比下管内流动分离,提升喷射泵来流的品质,应用涡流发生器（VG）流动控制技术,在进水管内部以及入口前的船底加装涡流发生器。采用雷诺时均模型和SST-kω湍流模型数值模拟进水管内流场,从流动分离、涡系分布和整体性能等方面分析了不同位置VG对进水管流场特性的影响,揭示了VG抑制进水管流动分离的控制机理。结果表明,VG产生流向涡驱动主流与斜坡侧边界层低能流体进行动量交换,增加边界层内的流向动量,从而抑制进水管斜坡侧的流动分离。流向涡在分离区内会发生方向偏移导致进水管内流场不对称。VG在进水管内产生的流向涡强度以及自身附加损失都会影响其控制效果。通过优选VG安装位置,进水管出口的不均匀度系数从0.406下降至0.318,旋流度从3.23°下降至2.14°,出口总压畸变减小,整体效率得到有效提升。     

端壁合成射流对高负荷涡轮叶栅涡系结构和流动损失影响的数值研究

为探究端壁合成射流对高负荷涡轮叶栅中涡系结构和流动损失的影响,采用非定常数值模拟方法分析了不同激励参数下合成射流对Durham叶栅流动损失的控制效果以及涡系结构和流动损失的对应关系。结果表明,合成射流减小了前缘马蹄涡和通道涡的尺度,削弱了来自相邻叶片压力面的横向涡,略微增强了壁角涡,并间接削弱了壁面涡;在无量纲幅值和频率分别为0.073和1时,控制效果最佳,总压损失系数减小约为10.72%;从控制机理上讲,合成射流加强了主流和射流下游边界层的掺混,增加了边界层动量,从而削弱了马蹄涡;合成射流影响了叶片压力面的流动分离,改变了由于分离产生低能流体的位置和范围,从而削弱了横向涡。由于漩涡的削弱,流动损失也随之减小。     

射流旋涡发生器控制大折转角扩压叶栅二次流

将射流旋涡发生器引入到某折转角为60°的扩压叶栅端壁二次流控制中,研究了射流方向和射流总压对扩压叶栅气动性能及栅内流动的影响.结果表明:当射流旋涡发生器侧向倾角为0°时,仅采用不足扩压叶栅进口流量0.5%的射流流量,即可显著减少栅内损失.射流旋涡有效阻碍和推迟了通道涡发展,在下洗侧将主流流体卷入端壁附面层内,而在上洗侧将低能流体带入主流中,从而减少了角区低能流体聚积,减弱了吸力面的分离流动.当射流进口总压采用与扩压叶栅进口相同的总压时,总压损失减小21.5%,且射流进口总压越大,其控制效果越明显.      

基于端壁涡流发生器的压气机叶栅角区分离控制研究

为研究被动式涡流发生器抑制压气机叶栅横向二次流以控制角区分离的作用,设计了在叶栅内部端壁处加装涡流发生器的控制方案,采用数值模拟的方法,详细分析了叶栅流场特性。结果表明:涡流发生器可以有效地抑制叶栅内部横向二次流,改善角区流动,在最佳控制方案中,总压损失系数下降8.1%;放置于叶栅内部的涡流发生器能阻挡气流的横向流动,其尾部产生的流向涡与横向迁移的端壁附面层相互作用,抑制了通道涡向吸力面的发展,并将主流高能流体卷入角区,增加角区流体动量;涡流发生器的长度和高度都会影响流向涡的强度,流向涡的涡核高度与涡流发生器高度一致,最终的控制效果由涡流发生器的长度和高度共同决定,只有当它们被合理选择,控制方案才能获得最佳控制效果。     

涡流发生器对Bump进气道性能影响数值研究

以一种Bump进气道为研究对象,通过在S弯扩压段入口处布置涡流发生器来控制流动分离,减小出口总压畸变。采用CFD数值计算软件对Bump进气道在设计点(Ma=2.0)与非设计点(Ma=1.8,0.8)工况下内、外流场进行计算,分析不同涡流发生器方案的效果。计算结果表明:在设计点工况下,安装涡流发生器能够抑制流动分离,改善进气道流场品质,减小出口总压畸变;在一些非设计点工况下会增大Bump进气道出口总压畸变;Bump进气道总压损失有所增大,不同叶片间距的涡流发生器对总压损失的影响相当。      

凹型面埋入式涡流发生器控制分离流

本文介绍了一种新型的凹型面埋入式涡流发生器的工作机理。并介绍在一个小宽高比二元单边凹壁亚声扩压壁前段出现气流分离,角落区域有倒流的情况下,采用适当几何参数的该型式涡流发生器大大减小分离区的范围,从而提高了扩压器静压恢复系数和减小总压损失系数的试验结果。     

埋入式涡流发生器在亚音扩压器分离流控制中的应用

本文介绍了在一个大宽高比大扩压角二元亚音扩压器中采用适当几何参数的凹型面埋入式涡流发生器有效地控制扩压壁和角落区域分离流的试验结果。并分析了该型式涡流发生器主要几何参数对扩压器性能的影响。还对该型式涡流发生器与常规翼型式涡流发生器进行了比较。      

7一种双S形进气道流场特性殛控制的试验研究

In order to provide the line of-sight blockage of the engine face for an advanced Uninhabited Combat Air Vehicle(UCAV), a highly curved serpentine inlet is proposed and experimentally studied. Based on the static pressure distribut ion measurement along the wall, the flow separation is found at the top wall of the second S duct for the baseline inlet design, which yields a high flow distortion at the exit plane. To improve the flow uniformity, a single array of vortex generators (VGs) is employed within the inlet. In this experimental study, the effects of mass flow ratio, free stream Mach number, angle of attack and yaw on the performance of a serpentine inlet instrumented with VGs are obtained. Results indicate: (1) Compared with the baseline serpentine design without flow control the application of the VGs promotes the mixing of core flow and the low momentum flow in the boundary layer and thus prevents the flow separation. Under the design condition, the exit flow distortion (

) decreases from 11. 7% to 2.3% by using the VGs. (2) With the descent of the free stream Mach number the total pressure loss decreases. How ever, the circular total pressure distortion increases. When the angle of attack rises from - 4° to 8°, the total pressure recovery and the circular total pressure distortion both go down. In addition, with the increase of yaw the total pressure recovery is fairly constant, while the circular total pressure distortion ascends gradually. (3) When Ma₀=0.6-0.8, α= −4°-8° and β= 0°-6°, the total pressure recovery varies between 0.936 and 0.961, the circular total pressure distortion coefficient varies between 1.4% and 5.4% and the synthesis distortion coefficient has a ranges from 3.8% to 7.0%. The experimental results confirm the excellent performance of the newly designed serpentine inlet incorporating VGs.     

不同来流附面层厚度下容腔泄漏流对围带式静叶性能影响

基于验证的数值模拟方法，针对带容腔结构的围带式静叶，研究了容腔泄漏流对其性能的影响以及容腔泄漏流与主流的相互干涉作用。在不同的来流附面层厚度下，探讨了叶栅二次流运动和角区分离发展情况，并通过总压损失系数和熵增系数对性能变化进行评判。结果表明：附面层厚度的增加使无容腔扩压叶栅总压损失系数和熵增损失系数增加。容腔泄漏流使叶片前缘出现容腔泄漏涡，并对通道涡的发展和集中脱落涡的大小产生影响；同时容腔泄漏流加强了叶栅通道内的三维流动效应，削弱了近端壁面流体的横向偏转；随着附面层增厚，带容腔的扩压叶栅的总压损失系数和熵增损失系数变化程度不明显。     

Experimental investigation of flow and distortion mitigation by mechanical vortex generators in a coupled serpentine inlet-turbofan engine system

The performance of compact, aggressive ducts in advanced propulsion systems is limited by the internal flow separation coupled with the formation of secondary counter-rotating vortices that give rise to intensive flow distortions at the duct exit. An experimental investigation was conducted to study the flow field and passive suppression of flow separation and Aerodynamic Interface Plane (AIP) distortion in a serpentine air inlet duct. Tests were performed by a turbofan engine at several Engine Operating Points (EOPs) from 56% (idle) to 100% (max). A large total pressure deficit region arose at the upper part of the AIP, which was associated with the upper surface flow separation. Using the new mechanical S-type vortex generators in two longitudinal positions (VG1 and VG2), separation and loss were diminished at the upper part of the duct and AIP. The VG2 arrangement attained the maximum reductions in distortion coefficients which were 73.72%, 60.7% and 37.8% in DC(90°), DC(60°) and ΔP_C/P metrics, respectively. In the next step of the study, some unsteady aspects of the flow field were analyzed inside the duct. The separation onset and reattachment points were determined by the standard deviation of static pressure on the upper surface. The AIP spectral distribution showed that the boundary of low pressure and high pressure recovery regions was dominated by the maximum fluctuations. Furthermore, the PSD diagram of several probes at AIP revealed the vortex shedding frequency and its higher harmonics at separation region. The energy content of distinct unsteady spectral features in the bare configuration was significantly reduced using VGs, which showed the improvement of flow at the duct exit.     

Review of research on low-profile vortex generators to control boundary-layer separation

An in-depth review of boundary-layer flow-separation control by a passive method using low-profile vortex generators is presented. The generators are defined as those with a device height between 10% and 50% of the boundary-layer thickness. Key results are presented for several research efforts, all of which were performed within the past decade and a half where the majority of these works emphasize experimentation with some recent efforts on numerical simulations. Topics of discussion consist of both basic fluid dynamics and applied aerodynamics research. The fluid dynamics research includes comparative studies on separation control effectiveness as well as device-induced vortex characterization and correlation. The comparative studies cover the controlling of low-speed separated flows in adverse pressure gradient and supersonic shock-induced separation. The aerodynamics research includes several applications for aircraft performance enhancement and covers a wide range of speeds. Significant performance improvements are achieved through increased lift and/or reduced drag for various airfoils—low-Reynolds number, high-lift, and transonic—as well as highly swept wings. Performance enhancements for non-airfoil applications include aircraft interior noise reduction, inlet flow distortion alleviation inside compact ducts, and a more efficient overwing fairing. The low-profile vortex generators are best for being applied to applications where flow-separation locations are relatively fixed and the generators can be placed reasonably close upstream of the separation. Using the approach of minimal near-wall protuberances through substantially reduced device height, these devices can produce streamwise vortices just strong enough to overcome the separation without unnecessarily persisting within the boundary layer once the flow-control objective is achieved. Practical advantages of low-profile vortex generators, such as their inherent simplicity and low device drag, are demonstrated to be critically important for many applications as well.     

端壁抽吸位置对压气机叶栅角区分离控制的影响

以某高负荷压气机叶栅为研究对象,应用数值模拟方法探索了叶栅端壁不同抽吸位置对角区流动结构、通道漩涡发展过程以及叶栅性能的影响规律,寻求控制角区分离的可行方法。研究结果表明:在叶栅前缘上游5%C(弦长)位置实施抽吸,延缓了通道涡的形成,但导致叶栅来流攻角发生改变,在角区形成角区分离涡,并且该漩涡与通道涡相互促进,进一步恶化叶栅流场,导致叶栅落后角增大,损失增加;在叶栅通道激波后25%C端壁抽吸,吸除了上游端壁积累的高熵低能气流,制约了通道涡的迅速发展,改善了叶栅通道的流场结构,降低了流动损失,但并未对上游流场产生较大影响,是一种可行的方案。然而25%C处抽吸后,未能完全消除分离,在端部与叶栅通道主流之间存在较高损失区域。     

基于涡流发生器的风洞侧壁附面层控制

为降低风洞侧壁附面层对半模型数据的影响,在前期数值模拟的基础上,研制了一种适用于2.4m跨声速风洞半模型试验段侧壁的梯形涡流发生器,并进行了试验验证.结果表明:加装涡流发生器效果明显,亚声速范围内能够使附面层厚度降低20%~30%,对主气流均匀性影响可忽略;加装后半模型零升阻力系数降低,升力线斜率增大,压力中心向机身移动,体现了明显的附面层减薄效果,证明所研制的涡流发生器可应用于亚声速半模型试验中.