闭环光纤陀螺量程扩展方法研究

从闭环光纤陀螺工作原理出发,分别对跨条纹调制法和单级干涉条纹量程扩展法两种扩展闭环光纤陀螺量程的方法进行了分析。结果表明基于单级干涉条纹的量程扩展方法在工程上更加简单易行,基本不用对算法和硬件进行改动,具有很高的工程实用价值。     

闭环光纤陀螺量程扩展方法研究

从闭环光纤陀螺工作原理出发,分别对跨条纹调制法和单级干涉条纹量程扩展法两种扩展闭环光纤陀螺量程的方法进行了分析。结果表明基于单级干涉条纹的量程扩展方法在工程上更加简单易行,基本不用对算法和硬件进行改动,具有很高的工程实用价值。     

双通道光纤陀螺捷联惯导的设计与实现

针对光纤陀螺惯导精度和动态性能相互矛盾的问题,从实际应用需求出发,提出了一种高精度和大量程的双通道光纤陀螺捷联惯导系统.介绍了设计的基本原理和系统组成,并详细阐述了大小光纤陀螺设计、双通道加速度计设计和软件算法设计等关键技术,最后研制了一套原理样机.通过系统级标定试验、量程和陀螺精度试验、高动态振动环境试验和动态跑车试验等对样机进行验证,结果表明该技术方案具有可行性,为其他光纤陀螺惯导系统提供了新的设计思路.     

基于高灵敏超导探测器的新型脉冲光高精度光纤陀螺技术研究

高精度光纤陀螺的精度主要由光纤陀螺检测噪声决定,一般可用角随机游走系数来表征,光纤陀螺的角随机游走主要由光路干涉信号的信噪比和信号处理引入的噪声决定。提出了基于高灵敏超导探测器的脉冲光高精度光纤陀螺技术方案和精度提升方法,实现了陀螺光信号的高灵敏检测,显著降低了光纤陀螺的热噪声,降低了相对强度噪声,并避免了连续光因调制切换引入的尖峰脉冲误差的影响,有效提升了光纤陀螺的精度水平。通过仿真分析,可将光纤陀螺的随机游走系数检测极限从3.53×10-5(°)/h1/2降低至1.6×10-5(°)/h1/2,减小了约54.7%。     

光纤陀螺捷联惯导系统中数据采集单元的设计与实现

研究了光纤陀螺捷联惯性导航系统中数据采集单元的设计与实现。系统选用Infel80C196KC单片机作为系统MCU,利用串口扩展芯片TL16C554实现对三路光纤陀螺信号的数据采集,采用16位高精度模数转换器AD676完成对加速度计信号的数据采集。论文给出了软硬件的实现方案和试验结果。试验结果表明该数据采集装置单元,满足系统的性能要求,有较强的实用价值。     

用于世界时测量的大型高精度光纤陀螺技术研究

综述了空间飞行器的精密定轨对世界时测量的需求,并对现有大型激光陀螺、光纤陀螺测量世界时的现状与前景进行了分析,阐述了大型高精度光纤陀螺用于世界时测量需重点解决的关键技术,对实现的大型高精度光纤陀螺样机进行了试验验证,零偏不稳定性达到了5.2×10-6(°)/h(1σ),同时对陀螺长期运行期间探测到的青海玛多地震情况进行了分析,最后对面向更高精度的世界时测量用大型光纤陀螺发展方向进行了展望.     

光纤陀螺惯导稳定平台与旋转调制方法

光纤陀螺仪在随机误差方面表现出极佳的性能优势,但受限于其标度因数不理想的现实。针对航海用长航时、高精度光纤陀螺惯导系统的使用需求,设计了基于光纤陀螺数字信号实现载体三维角运动隔离的同时完成惯性测量装置的旋转调制功能,可有效减小光纤陀螺标度因数误差与载体运动角速度的耦合误差,同时充分发挥光纤陀螺随机游走小的精度优势。理论仿真验证了光纤惯导稳定平台加旋转调制方法的优越性和可行性,为光纤陀螺惯导系统在高精度导航领域中的应用提供了技术基础。     

光纤陀螺磁屏蔽效能仿真及实验研究

光纤陀螺处于磁场环境中会产生漂移,降低了光纤陀螺精度。光纤陀螺的磁场敏感性制约了其在高精度导航领域的应用。本文建立了光纤陀螺三维磁屏蔽仿真模型,给出了光纤陀螺磁屏蔽效能与磁屏蔽结构参数之间的关系并得到实验验证,为光纤陀螺磁屏蔽设计提供了依据。     

光纤陀螺热致漂移仿真分析及实验验证

外界温度场作用下,光纤环温度变化和热应力是引起光纤陀螺非互易误差的主要原因。分析了光纤陀螺热致漂移的数学模型,基于该模型仿真研究了对光纤环以恒定功率加热随后转入平稳状态扰动因素下陀螺的输出特性。为验证模型准确性,选用3个光纤环搭建光纤陀螺系统,并对陀螺零偏变化特性进行了测试。测试结果表明,各陀螺零偏测试值与模型计算值间的误差不超过8%,实验结果与模型能够较好符合,该研究结果对高精度光纤陀螺的设计具有重要指导意义。     

新型三轴一体化光纤陀螺设计

我国光纤陀螺技术通过多年的研究与发展日趋成熟，目前光纤陀螺逐步向高精度、小型化方向发展。三轴一体化光纤陀螺结构紧凑、高度集成、体积小，符合光纤陀螺的发展特点，本文从光学回路、机械结构和信号处理等方面介绍三轴一体化光纤陀螺的研究情况。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.