Preliminary Evaluation of GPS Performance for Low-Cost General Aviation

Preliminary results of a simulation effort to evaluate the requirements and feasibility of the global positioning system (GPS) as a civil air navigation system are presented. Evaluation is made of GPS requirements, from operational considerations, such as application to nonprecision approaches. The conceptual low-cost GPS receiver simulated here does not correct for the ionospheric or trophospheric delay, is sequential in nature, tracks only four satellites, and is not mechanized to make independent range rate measurements based on the Doppler shift of the GPS carrier frequency. The proposed GPS system has significantly different performance characteristics from the presently used VHF omnidirectional range (VOR) solidus distance-measuring equipment (DME) system. The GPS is a low signal level system and many have a relatively slow data rate due to the low-cost sequential receiver design. The results indicate that although the conceptual low-cost GPS receiver/ navigator is potentially more accurate than a VOR, the accuracy may degrade during aircraft turns and satellite shielding periods.     

星基ADS-B接收机监视容量分析

星基广播式自动相关监视（ADS-B）系统是实现广域范围内航空器监视的重要技术手段。星基ADS-B系统内部存在严重的共信道干扰,共信道干扰限制了系统的监视性能。为了定量给出星基ADS-B接收机监视容量的计算方法,首先,给出了星基ADS-B系统的模型;随后,通过理论分析得到了星基ADS-B接收机报文冲突概率及报文正确接收概率,以此为基础理论,分析得出星基ADS-B接收机位置报文更新间隔及监视容量的计算方法;最后,构建了星基ADS-B仿真系统,仿真验证了理论计算公式的正确性。研究表明：星基ADS-B接收机的监视容量由飞机-卫星空天链路的误码率及ADS-B应用子系统所要求的位置报文更新间隔联合决定。     

Application of successive interference cancellation to the GPS pseudolite near-far problem

Ground-based transmitters called pseudolites have been proposed to augment the basic Global Positioning System (GPS) in environments where satellite visibility is limited. One difficulty in their use is the so-called near-far problem, where in close proximity to the ground transmitter, the pseudolite signal can be orders of magnitude stronger than the satellite signals. This large range of signal levels prevents a conventional receiver from simultaneously detecting both types of signals. This paper describes the application of a signal processing technique, known as successive interference cancellation (SIC), to the acquisition and tracking of weak satellite signals in the presence of a nearby pseudolite and possible multipath reflections of this pseudolite signal. The SIC architecture is implemented on simulated and experimental near-far data sets. The results are compared with a conventional detector and improvements in acquisition and tracking performance are illustrated.     

Interference Effects of Pseudo-Random Frequency-Hopping Signals

When a pseudo-random frequency-hopping signal is intercepted by a conventional receiver operating within the same frequency band, the interfering signal has the form of a pulse-amplitude modulated signal. Each pulse amplitude is dependent upon the hopping frequency and the selectivity characteristic of the victim receiver. The probability density function for the interfering pulse amplitude prior to demodulation is determined when the probability density function for the hopping frequency is uniform and the victim-receiver characteristic is 1) ideal flat bandpass, 2) single tuned, and 3) Gaussian shaped. It is shown that the average interfering pulse amplitude and interference power decrease as the frequency-hopping bandwidth increases with respect to the victim-receiver bandwidth. Fast Fourier transform computer techniques are used to obtain the probability density function of the interference amplitude in a Gaussian receiver when several (from 2 to 10) pseudo-random frequency-hopping systems are simultaneously using the same frequency band. The probability that the interference exceeds a prescribed threshold value is computed from the derived probability density functions. This probability may be used in signal-to-interference ratio calculations, to describe the capture effect, or to compute the expected number of clicks produced in an FM discriminator.     

Crop Dusting using GPS

Global Positioning System (GPS) receivers and GPS-based swath guidance systems are used on agricultural aircraft for remote sensing, airplane guidance, and to support variable-rate aerial application of crop inputs such as insecticides, cotton growth regulators, and defoliants. Agricultural aircraft travel at much greater speeds than ground equipment (65 m/s, typically), so longitudinal (along-track) error in GPS-derived position is likely to be pronounced. Due to rapid ground speeds, determination of exact GPS-derived aircraft location requires special methodologies. To meet the need for determining ground position accurately, a ground-based spotting system using two strategically placed mirrors was designed to reflect sunlight to the belly of the aircraft when the plane passed over a ground reference point. The light beam was detected by a photocell on the airplane, causing a solid state relay to close through appropriate circuitry. When the relay closed, a record was placed in the data file for the airplane's Satloc GPS receiver, accurate to 0.01 s allowing exact position to be logged. Two stand-alone GPS receivers were evaluated along with the Satloc system, and their readings were compared with readings from the Satloc. For one day of testing used as an example, the Satloc lagged the ground reference point by an average of -4.53 m (S.D. = 0.68) in the east-west directions and led the reference point in the north-south directions by an average of +7.88 m (S.D. = 0.52). Positioning data from one stand-alone GPS receiver showed a distinct ground speed dependency, making it unsuitable for use in aircraft. Output from the other receiver (designed for aircraft use) was insensitive to ground speed changes but exhibited a look-ahead equivalent to 2-s at the ground speeds evaluated.     

A novel approach for the SARSAT system

A novel method for determining the location of a 406-MHz emergency locator transmitter (ELT) for the search and rescue satellite aided tracking (SARSAT) system is proposed. The technique uses information from a geostationary satellite (Geosat) link, as well as the conventional polar orbiting satellite links. The method is based on solving a system of equations to determine the range from the ELT to the polar orbiting satellite (Polarsat) for each signal transmitted. Only two pulses need to be received from the ELT in order to obtain a location estimate. The main difference between the procedure outlined and the global positioning system (GPS) is that accurate time information is not available in the transmissions since aircraft and marine vessels seldom have accurate time standards onboard     

Multipath-adaptive GPS/INS receiver

Multipath interference is one of the contributing sources of errors in precise global positioning system (GPS) position determination. This paper identifies key parameters of a multipath signal, focusing on estimating them accurately in order to mitigate multipath effects. Multiple model adaptive estimation (MMAE) techniques are applied to an inertial navigation system (INS)-coupled GPS receiver, based on a federated (distributed) Kalman filter design, to estimate the desired multipath parameters. The system configuration is one in which a GPS receiver and an INS are integrated together at the level of the in-phase and quadrature phase (I and Q) signals, rather than at the level of pseudo-range signals or navigation solutions. The system model of the MMAE is presented and the elemental Kalman filter design is examined. Different parameter search spaces are examined for accurate multipath parameter identification. The resulting GPS/INS receiver designs are validated through computer simulation of a user receiving signals from GPS satellites with multipath signal interference present The designed adaptive receiver provides pseudo-range estimates that are corrected for the effects of multipath interference, resulting in an integrated system that performs well with or without multipath interference present.     

Reduction of interference from DGPS transmissions in the MF bandusing a GMSK modulation scheme

The accuracy of the Global Positioning System (GPS) can be improved by differential techniques. For maritime applications a DGPS service with transmissions by maritime radiobeacons in the MF band is provided. It offers a position accuracy of approximately 5 m. For the data link a minimum shift keying (MSK) modulation scheme has been recommended. The adjacent channel interference at the maximum transmission rate might not be consistent with existing frequency plans     

ATS-5 Millimeter Wave Propagation Experiment

This paper describes the design of the millimeter wave experiment aboard the ATS-5 satellite. This equipment is the first millimeter wave communications equipment in space. The function of the equipment is to provide earthspace propagation data at Ku- and Ka- band frequencies. The designs of the phase locked Ka- band receiver, the Ku-band transmitter, the antennas, and the telemetry and processing equipment are described. Mechanical and environmental problems are also discussed.     

Spectral Analysis of ELT Signals for SARSAT

Search and rescue satellite-aided tracking (SARSAT) relays the emergency locator transmitter (ELT) signals of distressed aircraft to an earth station for spectral analysis. Of considerable importance are the characteristics of the spectrum of the ELT signal since the probability of locating the downed aircraft is closely related to the quality of the ELT signal spectrum itself. In this paper, it is shown that the spectrum can be adversely affected by a number of factors including the phase and frequency characteristics of the carrier and their interaction with the amplitude modulation. Two new models are proposed which greatly reduce the self-generated interference produced by ELT units presently being used.     

Aircraft Interrogation Scheduling with ASTRO-DABS

In the ASTRO-DABS concept for surveillance and data link, aircraft are interrogated by one of three geostationary transmitter satellites, each covering 1/3 of the contiguous United States. Interrogation scheduling involves a roll call such that aircraft responses to receiving satellites do not overlap (garble). A simple approach is developed which utilizes range ordering of aircraft with respect to transmitter satellites, but is independent of receiver satellite locations and aircraft distribution. Bounds on roll-call duration are established, showing that interrogation of 80 000 aircraft requires between 4.0 and 6.4 seconds with the ASTRO-DABS transmission format. If aircraft distribution is regionally concentrated (i.e., clustered), the roll-call duration nears the lower bound, since fewer gaps between interrogations are needed to preclude garbling.     

传导干扰研究

传导发射是沿电源线或信号线传输的电磁发射,在低频范围内,传导发射是电磁干扰的主要形式。如不采取措施,几乎所有的电子、电气设备电源线的传导发射都得超标,若将这些设备安装在飞机上,它将严重地威胁着机上其他设备的正常工作。本文对各种脉冲波形的频谱进行了比较,并对整流器的谐波发射进行了分析,最后介绍了降低传导发射的设计方法。     

Multicomponent receiver architectures for GPS interference suppression

The global positioning system (GPS) is a one-way satellite-based navigation system employing spread-spectrum techniques that is widely used for commercial and military applications. Although the very low signal-to-noise ratio (SNR) is handled by the large spreading gain, GPS is susceptible to high-power interference signals and various types of jammers. We propose multicomponent receiver architectures for GPS interference suppression. A conventional antenna system is first considered which utilizes a minimum-variance distortionless-response (MVDR) beam former and assumes that the GPS signal angle of arrival (AOA) and the antenna model are known at the receiver. However, this receiver is sensitive to AOA estimation errors and can have a high computational complexity. This sensitivity problem is eliminated by a multicomponent system based on a multistage matched filter (MF). Since this MF receiver also has a high computational complexity because the jammer AOAs must be estimated, we introduce a blind interference canceler based on the constant modulus (CM) array that is insensitive to AOA estimation errors and has a low computational complexity. Computer simulations are provided to illustrate the performance of the various systems for interference suppression in example signal scenarios.     

Ensuring GPS navigation integrity using receiver autonomousintegrity monitoring

The many advantages of Global Positioning System (GPS) based navigation have created a tremendous amount of interest in using GPS as the primary navigation aid onboard commercial and civil aircraft. Even in the presence of Selective Availability, the accuracy of GPS is sufficient to guide aircraft point-to-point between airports without requiring other navigation aids such as VOR or DME. Unfortunately, there is a finite probability that a GPS satellite will fail, causing the transmission of potentially misleading navigation information. Thus, before GPS can be widely adopted as a navigation aid, techniques must be devised to detect any possible failures and notify the user prior to the degradation of navigation accuracy. This paper discusses the problem of detecting possible GPS satellite failures using a technique called Receiver Autonomous Integrity Monitoring (RAIM)     

利用有限域上二元多项式构造带仲裁的认证码

在传统的无条件安全认证码中,假定发方和收方是相互信任的,他们不会互相欺骗。但有些情况也可能不是这样,发方在发出一个消息后,不承认是他发的,收方捏造了一个消息,声称来自发方,在这种情况下就需要增添仲裁方。带仲裁的认证码能解决通信系统中发方与收方互不信任的问题。利用有限域上二元多项式构造了一个带仲裁的认证码,并计算了所构造码的参数。当编码规则按等概率分布选取时,计算出了敌方与收方成功模仿攻击和成功替换攻击的最大概率．以及发方成功模仿攻击的最大概率。     

UV 波段的宽带可重构收发机的实现

设计了一种宽带可重构收发机,主要由三部分组成：发射机、接收机和频率源。发射机完成从中频 70 MHz 到100~550 MHz 的射频发射,为了减小发射信号对相邻信道的干扰,发射信号的杂散抑制要高。接收 机从众多的电波中选出有用信号,并将该信号搬移到中频信号,然后放大到解调器所要求的电平值,将射频信 号变为中频信号,由于传输路径上的损耗和多径效应,接收机接收的信号是微弱且有变化的,并伴随着许多干 扰,这些干扰信号强度往往远大于有用信号,因此接收机的主要指标是灵敏度和选择性。频率源提供精确和低 噪声的本振信号,为射频变频系统核心部分之一,频率源的主要指标是相位噪声。     

A localizer design to improve missed approach guidance

A novel VHF localizer system has been designed, built and successfully tested to provide increased reliability and safety of commercial and general aviation air transportation. Additional benefits are more precise tracks for aircraft executing a missed approach, reduced volume of the airspace needed for missed approaches, and reduced sizes of areas affected by noise. The design uses contemporary instrument landing system (ILS) hardware to provide dual independent front and back course directional localizer operation with two carriers in the receiver passband offset 4 kHz from the nominal carrier frequency. An example is given of an application and solution to an ILS problem at Reno, NV. Relevant data are presented     

脉冲干扰对软件接收机的影响分析

卫星信号经过长距离传播,信号能量损耗严重,到达地面的功率很弱,容易受到各种干扰的影响。脉冲干扰为常见的干扰类型,所以针对不同功率、不同周期,以及不同占空比的脉冲干扰信号,通过接收前端采集受脉冲干扰的GPS L1信号,利用软件接收机及多相关器生成技术,详细分析了脉冲干扰对接收机信号捕获与跟踪性能的影响。分析结果表明,周期为1ms的脉冲干扰信号,能对接收机产生强烈的干扰效果,捕获图中的噪声明显增大;跟踪过程中,载噪比和相关值突发性减小,造成跟踪数据异常。而长周期的脉冲信号仅在脉冲到达时影响接收机的捕获和跟踪,但由于信号跟踪不能连续进行,导致伪距观测量的不连续与导航数据不能正常解码,从而干扰接收机。     

基于Kalman滤波的GPS/INS接收机自适应干扰抑制方法

 考虑到惯导信息辅助GPS(GPS/INS)接收机对干扰抑制实时性的要求,提出一种基于Kalman滤波的GPS/INS接收机自适应干扰抑制方法。自适应广义旁瓣相消(GSC)多采用低复杂度最小均方(LMS)算法更新权矢量,收敛速率较低,严重时会导致接收机定位中断。首先利用Householder变换构建GSC下支路的阻塞矩阵,用于阻塞任意二维阵型阵列接收的期望信号;再用Kalman滤波自适应更新下支路权矢量,从而有效提高阵列输出信干噪比(SINR)。理论分析和仿真结果说明本文方法可有效抑制干扰对接收机的影响,且具有实时性高的特点。     

民用飞机甚高频通信系统适航审定技术分析

民用飞机进行可靠的空地、空空通信,对飞行安全尤为重要。甚高频(very high frequency,简称VHF)通信系统是目前应用最为广泛的航空通信方式,VHF通信系统通过与机上音频系统交联实现飞机与外部的语音通信,通过与机上数据链系统交联实现飞机与地面的数据链通信。甚高频通信系统与民用飞机的安全运行密切相关,也是适航规章和运行规章要求的内容。结合甚高频通信系统功能要求和设计架构,针对适用于甚高频通信系统的中国民用航空规章第25部：运输类飞机适航标准(CCAR-25-R4-2011)条款,分析并给出甚高频通信系统可接受的符合性方法,同时根据型号工作经验给出甚高频通信系统在适航审查中的审定要素。针对甚高频通信系统所涉及的各项条款,为局方提供了适航审查工作需要关注的审定要素和评审要求。研究有助于民机甚高频通信系统的安全设计与适航验证。