开关点预置三相四线SPWM逆变器研究

脉宽调制型交直交变速恒频电源采用开关点预置SPWM逆变器,该逆变器由三相桥,交流滤波器,中点形成变压器及控制、驱动电路组成。绝缘栅双极性晶体管是一种新型的电力电子器件;应用该器件为功率器件,研制了一套15kVA开关点预置SPWM逆变器。由于对电路各个部分均进行了充分分析和优化设计,实际制作的逆变器具有较小的体积、重量,并具有优越的电性能。     

Single-phase grid-connected PV system using three-arm rectifier-inverter

A grid-connected photovoltaic (PV) power supply system with on-line voltage regulation capability is presented. It employs the three-arm rectifier-inverter topology with PV modules connected directly on the dc-link. The common-arm is with line-frequency switching and synchronous to the input voltage, aiming for a lower switching loss and decoupling the control of rectifier and inverter portions. As a result, the rectifier and inverter portions can be controlled independently with the rectifier-arm and inverter-arm, respectively. For maximum power point tracking (MPFF) of the PV modules and balancing the power among utility, PV, and the load, a variable dc-link voltage is adopted and controlled by the rectifier-arm based on the MPPT control algorithm. The inverter-arm then regulates the load voltage with good regulation and low distortion. Due to large variation of the dc-link voltage, a feedforward plus feedback control technique with variable gain is developed to keep constant bandwidth of the current loop at any operation condition. Therefore, the performance of the rectifier and inverter portions can be ensured. A system containing a 2 kVA converter and a 1.2 kW PV module is set up, and some experimental results are provided for demonstrating the effectiveness of the proposed method.     

Development of a driver board power supply for high power IGBTsused in three-phase inverters

High power IGBTs have been widely used for medium power inverters up to 200 kVA. Their driver circuits often require multiple-output, isolated power supplies. This paper presents a simple flyback power supply especially designed for the driver boards of three-phase IGBT inverters. The detailed circuit diagrams and typical waveforms are reported. Certain performance data are given. The power supplies have been used in 100 kVA inverters for an electric vehicle drive and for a wind turbine inverter     

SPWM逆变器交流瞬时值反馈控制系统分析

针对应用于交直交VSCF飞机电源系统的SPWM逆变器,提出了包含交流电流内环和交流电压外环的双闭环控制系统方案,利用交流瞬时值反馈的波形校正作用使逆变器输出电压波形得以改善。通过对单相1 kVA SPWM逆变器双闭环控制系统的设计分析和实验研究,结果表明:采用交流瞬时值反馈控制的SPWM逆变器具有较好的输出电压波形、动态响应特性和稳态调压精度,对逆变器输入直流电压的变化影响有很好的抑制作用,适合任由永磁无刷直流发电机供电的VSCF电源系统中应用。     

Improved DC/AC interface inverter for high-frequency spaceapplications

A DC/AC interface inverter for a high-frequency space power distribution system that uses dual asymmetrical resonant bridges is examined. Compared to the conventional approach in which two symmetrical bridges are used, the asymmetrical bridges arrangement offers better use of the installed kVA rating and efficiency of the inverter system. A simplified approach for modeling the inverter system in steady-state is presented, and a criteria to select the resonant components is given. A detailed simulation is performed for the following: a symmetrical inverter system with a resistive load, an asymmetrical inverter system with a resistive load, and an asymmetrical inverter system with the type-1A AC/DC converter load     

高速磁悬浮电动机变频器用开关电源设计

采用基于NCP1200的电流型控制,设计并研制了应用于高速磁悬浮电动机变频器的开关电源,该电源自适应输入电压波动,并自动调节PWM占空比以保证输出电压恒定.实验结果表明,该电源具有输出纹波小、效率高、EMI小、电压调整率和稳压性能好等优点,可用作变频器控制电路的电源.     

A design procedure for the phase-controlled parallel-loadedresonant inverter

High-frequency-link power conversion and distribution based on a resonant inverter has been recently proposed. The design of several topologies is reviewed and a simple approximate design procedure is developed for the phase-controlled parallel-loaded resonant inverter. This design procedure seeks to ensure the expected benefits of resonant conversion and is verified by data from a laboratory 2.5 kVA, 20-kHz converter. A simple phasor analysis is introduced as a useful approximation for design purposes. Experimental results show that under transient conditions such as load short-circuit, a reversal of the expected commutation sequence is possible. This should be accounted for in the design of the power circuit, or prevented by the design of the controller     

PWM inverter technology

The approach used to optimize a transistorized pulsewidth-modulated inverter used in an uninterruptible power supply is detailed. Through the use of computer modeling with a space state-model, a variety of scenarios for the optimal inverter design were evaluated. The computer modeling resulted in an optimized feedback control loop, which provided the best level of response while minimizing the amount of switching losses to achieve the highest level of efficiency     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

Improved Mapham's inverter for HF space power conversion

An improved Mapham's inverter for high-frequency space power conversion is presented. The proposed inverter system uses a starting commutator to facilitate the starting of the conventional inverter under full-load conditions. The load conditions which cause the starting commutation failure of a conventional Mapham inverter are established. An improved inverter system to overcome the starting failure is presented and analyzed. The behavior of the improved inverter has been simulated to verify the predicted performance at start-up. A steady-state analysis of the inverter is presented, and the performance characteristics are derived     

Single-stage converters for PV lighting systems with MPPT andenergy backup

Single-stage converters (SSCs) are proposed for applications of photovoltaic powered lighting system (PPLS). The synchronous switch technique is employed to develop the SSCs which can fulfill maximum power point tracking (MPPT), battery charging, discharging, and lamp ballasting features. Several typical SSCs are discussed. One of the proposed SSCs, which is the integration of a buck-boost charger/discharger and a class-D series resonant parallel loaded inverter, is analyzed and designed into a PPLS. Both pulsewidth modulation (PWM) and variable-frequency controls are used to govern the system operation. The controller is implemented on a single-chip microprocessor. Simulated and experimental results of the proposed system for driving up to sixteen GE TBX 26 W fluorescent lamps are used to verify the theoretical prediction and feasibility. The proposed system has a simple configuration, as well as a zero voltage switching (ZVS) feature, and can achieve the same functions as those in conventional systems when abrupt insolation changes do not occur frequently. These result in the inherent merits of lower cost, more compact size and possibly achieving higher reliability over conventional systems     

Stepped Sinewave Inverter

A stepped sinewave dc/ac inverter was analyzed for an inductive load with respect to load current and voltage, harmonics, power factor, and efficiency. This special inverter of high efficiency and low harmonic content is constructed by synthesizing the sinusoidal output by discrete voltage sources, such as storage batteries, solar cell, etc., with electronic switching of the sources at specific time intervals. The switching times are determined for the condition of minimum distortion of the synthesized wave. A 50 W inverter was built and tested to demonstrate this approach.     

Implementation of nondeterministic pulsewidth modulation forinverter drives

A single-phase power factor preregulator to improve the power quality in the input side of an ac/dc/ac converter and a random pulsewidth modulation (PWM) to reduce the emitted noise energy and the mechanical vibration for an induction motor drive is proposed. The hysteresis current control (HCC) technique for a voltage source switching mode rectifier (SMR) is adopted. A control scheme is presented such that the line current is driven to follow the reference current which is derived from the dc bus voltage regulator and the output power estimator. A random pulse position technique for a three-phase voltage source inverter system to reduce the noise energy and resonant vibration from ac machine drive is described. By randomly varying the instantaneous pulse position in each switching frequency, the frequency distribution of harmonics is spread in a wide frequency range which results in reduction of torque pulsations in the ac motor drive systems. To investigate the proposed control scheme, experimental tests based on a laboratory prototype were implemented to show the nearly unity power factor at the SMR and reduce the noise energy concentrated at the specific tones     

混合型逆变器的空间矢量调制策略优化

高速永磁同步电机驱动系统具有电磁时间常数小、高速区载波比低的特征,加剧了电流纹波,影响系统效率、振动噪声和电磁干扰。为降低高速永磁同步电机的电流纹波,基于SiC-MOSFET/Si-IGBT混合型逆变器设计了一种改进型低损耗空间矢量调制算法。首先,通过调整零电压矢量的生成方式和各功率器件的开关动作时序,将大部分开关动作转移至低损耗的SiC-MOSFET中,并为高损耗的Si-IGBT提供零电压开关条件,降低了逆变器损耗,提高了驱动系统的效率和可用开关频率,逆变器开关频率的提高有效降低了电机电流纹波。其次,对该算法作用时的电流纹波特性进行深入分析,在此基础上提出一种变开关频率模式的最优交轴电流纹波峰值调制算法以优化交轴电流纹波性能。然后,根据预测的交轴电流纹波峰值实时调整载波频率,通过削峰填谷的方式对交轴电流纹波进行平均,在不增加开关损耗的条件下,分散开关能量、降低转矩脉动、改善振动噪声和电磁兼容性能。所提方案的优势在于：较于传统型逆变器,逆变器开关损耗降低、效率提高,可进一步提升开关频率以改善电流纹波;较于传统空间矢量调制算法,改进了电压矢量的生成方式,并利用载波频率这一新增自由度分散能量,降低了交轴电流纹波。最后,通过仿真与实验对所提出算法的有效性进行了验证。     

Generic functional modelling of multi-pulse auto-transformer rectifier units for more-electric aircraft applications

The Auto-Transformer Rectifier Unit (ATRU) is one preferred solution for high-power AC/DC power conversion in aircraft. This is mainly due to its simple structure, high reliability and reduced kVA ratings. Indeed, the ATRU has become a preferred AC/DC solution to supply power to the electric environment control system on-board future aircraft. In this paper, a general modelling method for ATRUs is introduced. The developed model is based on the fact that the DC voltage and current are strongly related to the voltage and current vectors at the AC terminals of ATRUs. In this paper, we carry on our research in modelling symmetric 18-pulse ATRUs and develop a generic modelling technique. The developed generic model can study not only symmetric but also asymmetric ATRUs. An 18-pulse asymmetric ATRU is used to demonstrate the accuracy and efficiency of the developed model by comparing with corresponding detailed switching SABER models provided by our industrial partner. The functional models also allow accelerated and accurate simulations and thus enable whole-scale more-electric aircraft electrical power system studies in the future.     

Design optimization for asymmetrical ZVS-PWM zeta converter

In this paper, a new soft-switching Zeta converter with an asymmetrical pulsewidth modulation (PWM) control is proposed. The proposed Zeta converter has the features of constant frequency operation, zero voltage switching (ZVS), and low voltage stress on the active switches. Moreover, it can achieve high power density, high efficiency, low switching loss, and low component count, which make converter operation at low to medium power level feasible. Operational principle of the Zeta converter is presented in detail, and a specific example is designed and implemented to verify its feasibility.     

超级电容储能系统的状态识别与动态控制设计

根据变频器母线电流在电机运行于加载和制动时的不同特征,通过采集变频器母线电流实时监测电机运行状态,设计了双向DC/DC变换器模式切换与控制器通断控制电路,实时识别电机运行状态,实现对储能单元在线动态控制。通过搭建550 W的储能系统试验平台,验证了所设计状态识别与控制电路的合理性。     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

270-VDC/hybrid 115-VAC electric power generating system technologydemonstrator

The approach, system architecture, instrumentation, and performance of a technology demonstrator system for the application of 270-VDC/hybrid 115-VAC electrical power generation and distribution to future military aircraft are examined. The design has focused on assembling a highly flexible test system. The loads are typical of those in a hybrid electrical system. The system consists of a single 3-phase, 115-VAC electrical generator whose output is rectified, filtered, and supplied through DC contactors to both a 270-VDC load bus and to the input of an inverter, which supplies a 400-Hz, 115-VAC load bus. A variable-frequency, 115-VAC bus is also available directly from the generator. A prototype variable-speed constant-frequency 120-kVA generator is used. The test facility is designed to provide loads to all power types capable of being produced by the system. The system has provided particularly good insight into various aspects of 270-VDC/115-VAC hybrid systems and their components     

Novel single-stage half-bridge series-resonant buck-boost inverter

A novel single-stage half-bridge series-resonant buck-boost inverter (HB-SRBBI) is proposed. The main attribute of the novel inverter topology is the fact that it generates an ac output voltage larger or lower than the dc input one, depending on the instantaneous duty cycle. This property is not found in the classical voltage source inverter (VST), which produces an ac output instantaneous voltage always lower than the dc input voltage. The proposed inverter circuit topology provides the main switch for turn-on at zero-current-switching (ZCS) by an auxiliary resonant cell built before the output choke. A state-space averaging approach is employed to analyze the system. A design example of 500 W ac/dc inverter is examined to assess the inverter performance and it provides high power efficiency above 90.7% under the rated power.