YES2 optimal trajectories in presence of eccentricity and aerodynamic drag

YES2 (launching 2007) aims to demonstrate a tether-assisted re-entry concept, whereby payload will be returned to Earth using momentum provided from a swinging tether. Deployment takes place in two phases: (1) deployment of 3.5 km of tether to the local vertical and hold, and (2) deployment to 30 km for a swinging cut. Optimal trajectories are determined for both phases after comparing the effect of different cost functions on the deployment dynamics. Closed-loop control is provided by linearizing the dynamics around the optimal trajectories and solving a receding horizon control problem for a set of linear feedback gains. The controllers are tested in a flexible tether model with large disturbances to the hardware model and environmental variables. Closed-loop simulations show that the system can be controlled quite well using only feedback of length and length rate.     

Results of the parabolic flight tests of the rapunzel deployer

The tether assisted re-entry of small payloads is a highly interesting tool for space transportation especially for the return of small payloads from Space Station ISSA. The small tether mission Rapunzel was initiated in 1991 by the Institute of Astronautics, TU München and the Kayser-Threde Company, to design a low cost and feasible tether experiment for the verification of the tether assisted re-entry. Together with the Samara State Aerospace University, Russia, a mission concept on a Russian Resurs or Photon capsule was developed. Based on this mission a deployer has been designed, mainly based on technology of the textile industry, which insures high reliability at low cost. Recently a similar configuration is being discussed for the ESA-TSE mission.The main work during the recent time was the development and test of the breadboard model of the deployer system. After successfully completing initial ground tests with the deployer, further tests during the ESA Parabolic Flight campaign in November 1995 were conducted. After a short introduction of the overall mission scenario, the planned configuration in orbit, this paper will present the results of the microgravity test campaign onboard the KC-135 aircraft and compare them with the ground test. The deployer showed a good performance during all tests, including ejection of the end-mass, deployment, and braking. Problems that occurred during the tests will be discussed, and solutions for the detected flaws and the results of the redesign now in progress will be presented. These verifications have shown the feasibility of the concept and will lay the base for the planned development of the flight model of the deployer.     

Very high delta-V missions to the edge of the solar system and beyond enabled by the dual-stage 4-grid ion thruster concept

A new and innovative type of gridded ion thruster, the “Dual-Stage 4-Grid” or DS4G concept, has been proposed and its predicted high performance validated under an ESA research, development and test programme. The DS4G concept is able to operate at very high specific impulse and thrust density values well in excess of conventional 3-grid ion thrusters at the expense of a higher power-to-thrust ratio. This makes it a possible candidate for ambitious missions requiring very high delta-V capability and high power. Such missions include 100 kW-level multi-ton probes based on nuclear and solar electric propulsion (SEP) to distant Kuiper Belt Object and inner Oort cloud objects, and to the Local Interstellar medium. In this paper, the DS4G concept is introduced and its application to this mission class is investigated. Benefits of using the DS4G over conventional thrusters include reduced transfer time and increased payload mass, if suitably advanced lightweight power system technologies are developed.A mission-level optimisation is performed (launch, spacecraft system design and low-thrust trajectory combined) in order to find design solutions with minimum transfer time, maximum scientific payload mass, and to explore the influence of power system specific mass. It is found that the DS4G enables an 8-ton spacecraft with a payload mass of 400 kg, equipped with a 65 kW nuclear reactor with specific mass 25 kg/kW (e.g. Topaz-type with Brayton cycle conversion) to reach 200 AU in 23 years after an Earth escape launch by Ariane 5. In this scenario, the optimum specific impulse for the mission is over 10,000 s, which is well within the capabilities of a single 65 kW DS4G thruster. It is also found that an interstellar probe mission to 200 AU could be accomplished in 25 years using a “medium-term” SEP system with a lightweight 155 kW solar array (2 kg/kW specific mass) and thruster PPU (3.7 kg/kW) and an Earth escape launch on Ariane 5. In this case, the optimum specific impulse is lower at 3500 s which is well within conventional gridded ion thruster capability.     

Design and on-orbit performance of the attitude determination and control system for the ZDPS-1A pico-satellite

The ZDPS-1A pico-satellite, developed by the Zhejiang University, is featured with a three-axis stabilizing capability. It is 15×15×15 cm³ cube-shaped satellite with a total mass of 3.5 kg. ZDPS-1A is the first pico-satellite that has been launched successfully in China. The mission of ZDPS-1A is on-orbit system verification of student-build pico-satellite and wide range earth observation with a micro panoramic camera. A miniature momentum wheel is employed to offer gyro stiffness stability in the pitch (orbit normal) axis. Magnetic coils are employed to generate control torques to achieve the three-axis stabilization of nadir-pointing. The attitude sensors employed in the design include two three-axis magnetometers (TAMs), a three-axis gyro, and two sun sensors. Both ground simulations and on-orbit testing are conducted to verify the feasibility of the given attitude determination and control system (ADCS).     

Venus surface power and cooling systems

A mission to the surface of Venus would have high scientific value, but most electronic devices and sensors cannot operate at the 450 °C ambient surface temperature of Venus. Power and cooling systems were analyzed for Venus surface operation. A radioisotope power and cooling system was designed to provide electrical power for a probe operating on the surface of Venus. For a mission duration of substantial length, the use of thermal mass to maintain an operable temperature range is likely impractical, and active refrigeration may be required to keep components at a temperature below ambient. Due to the high thermal convection of the high-density atmosphere, the heat rejection temperature was assumed to be at a 500 °C radiator temperature, 50 °C above ambient. The radioisotope Stirling power converter designed produces a thermodynamic power output capacity of 478.1 W, with a cooling power of 100 W. The overall efficiency is calculated to be 23.36%. The mass of the power converter is estimated at approximately 21.6 kg.     

Deployment history and design considerations for space reactor power systems

The history of the deployment of nuclear reactors in Earth orbits is reviewed with emphases on lessons learned and the operation and safety experiences. The former Soviet Union's “BUK” power systems, with SiGe thermoelectric conversion and fast neutron energy spectrum reactors, powered a total of 31 Radar Ocean Reconnaissance Satellites (RORSATs) from 1970 to 1988 in 260 km orbit. Two of the former Soviet Union's TOPAZ reactors, with in-core thermionic conversion and epithermal neutron energy spectrum, powered two Cosmos missions launched in 1987 in ～800 km orbit. The US’ SNAP-10A system, with SiGe energy conversion and a thermal neutron energy spectrum reactor, was launched in 1965 in 1300 km orbit. The three reactor systems used liquid NaK-78 coolant, stainless steel structure and highly enriched uranium fuel (90–96 wt%) and operated at a reactor exit temperature of 833–973 K. The BUK reactors used U-Mo fuel rods, TOPAZ used UO₂ fuel rods and four ZrH moderator disks, and the SNAP-10A used moderated U-ZrH fuel rods. These low power space reactor systems were designed for short missions (～0.5 kW_e and ～1 year for SNAP-10A, <3.0 kW_e and <6 months for BUK, and ～5.5 kW_e and up to 1 year for TOPAZ). The deactivated BUK reactors at the end of mission, which varied in duration from a few hours to ～4.5 months, were boosted into ～800 km storage orbit with a decay life of more than 600 year. The ejection of the last 16 BUK reactor fuel cores caused significant contamination of Earth orbits with NaK droplets that varied in sizes from a few microns to 5 cm. Power systems to enhance or enable future interplanetary exploration, in-situ resources utilization on Mars and the Moon, and civilian missions in 1000–3000 km orbits would generate significantly more power of 10's to 100's kW_e for 5–10 years, or even longer. A number of design options to enhance the operation reliability and safety of these high power space reactor power systems are presented and discussed.     

Development and evaluation of bioregenerative menus for Mars habitat missions

Two 10-day menus were developed in preparation for a Mars habitat mission. The first was built on the assumption, as in previous menu development efforts for closed ecological systems, that the food system would be vegetarian, whereas the second menu introduced shelf-stable, prepackaged meat and entrée items from the current International Space Station (ISS) food system. Both menus delivered an average of 3000 cal daily but the macronutrient proportions resulted in an excess of carbohydrates and dietary fiber per mission nutritional recommendations. Generally, the individual recipes comprising both menus were deemed acceptable by internal sensory panel (average overall acceptability=7.4). The incorporation of existing ISS entrée items did not have a significant effect on the acceptability of the menus. In a final comparison, the food system upmass, or the amount of food that is shipped from the Earth, increased by 297 kg with the addition of prepackaged entrées to the menu. However, the addition of the shipped massed was counterbalanced by a 864 kg reduction in required crops. A further comparison of the crew time required for meal preparation and farming, food system power requirements, and food processing equipment mass is recommended to definitively distinguish the menus.     

Sleep and cognitive function of crewmembers and mission controllers working 24-h shifts during a simulated 105-day spaceflight mission

The success of long-duration space missions depends on the ability of crewmembers and mission support specialists to be alert and maintain high levels of cognitive function while operating complex, technical equipment. We examined sleep, nocturnal melatonin levels and cognitive function of crewmembers and the sleep and cognitive function of mission controllers who participated in a high-fidelity 105-day simulated spaceflight mission at the Institute of Biomedical Problems (Moscow). Crewmembers were required to perform daily mission duties and work one 24-h extended duration work shift every sixth day. Mission controllers nominally worked 24-h extended duration shifts. Supplemental lighting was provided to crewmembers and mission controllers. Participants' sleep was estimated by wrist-actigraphy recordings. Overall, results show that crewmembers and mission controllers obtained inadequate sleep and exhibited impaired cognitive function, despite countermeasure use, while working extended duration shifts. Crewmembers averaged 7.04±0.92 h (mean±SD) and 6.94±1.08 h (mean±SD) in the two workdays prior to the extended duration shifts, 1.88±0.40 h (mean±SD) during the 24-h work shift, and then slept 10.18±0.96 h (mean±SD) the day after the night shift. Although supplemental light was provided, crewmembers’ average nocturnal melatonin levels remained elevated during extended 24-h work shifts. Naps and caffeine use were reported by crewmembers during ∼86% and 45% of extended night work shifts, respectively. Even with reported use of wake-promoting countermeasures, significant impairments in cognitive function were observed. Mission controllers slept 5.63±0.95 h (mean±SD) the night prior to their extended duration work shift. On an average, 89% of night shifts included naps with mission controllers sleeping an average of 3.4±1.0 h (mean±SD) during the 24-h extended duration work shift. Mission controllers also showed impaired cognitive function during extended duration work shifts.These findings indicate that extended duration work shifts present a significant challenge to crewmembers and mission support specialists during long-duration space mission operations. Future research is needed to evaluate the efficacy of alternative work schedules and the development and implementation of more effective countermeasures will be required to maintain high levels of performance.     

Launch and early operations of Herschel and Planck

On 14 May 2009 the European Space Agency launched 2 space observatories: Herschel (with a 3.5 m mirror it is the largest space telescope ever) will collect long-wavelength infrared radiation and will be the only space observatory to cover the spectral range from far-infrared to sub-millimetre wavelengths, and Planck will look back at the dawn of time, close to the Big Bang, and will examine the Cosmic Microwave Background (CMB) radiation to a sensitivity, angular resolution and frequency range never achieved before. This paper will present the Flight Dynamics, mission analysis challenges and flight results from the first 3 months of these missions.Both satellites were launched on the same Ariane 5 and travelled to the L2 Lagrange point of the sun–earth system 1.5 million km from the earth in the opposite direction of the sun. There they were injected to a quasi-halo orbit (Herschel) with the dimension of typically 750,000 km×450,000 km, and a Lissajous orbit (Planck) of 300,000 km×300,000 km.In order to reach these Lissajous orbits it is mandatory to perform large trajectory correction manoeuvres during the first days of the mission. Herschel had its main manoeuvres on the first day. Planck had to be navigated on the first day and by a mid-course correction manoeuvre, the L2 orbit insertion manoeuvre was planned on day 50. If these slots were missed, fuel penalties would rapidly increase.This posed a heavy load on the operations teams because both spacecrafts have to be thoroughly checked out and put into the correct modes of their attitude control systems during the first hours after launch.The sequence of events will be presented and explained and the orbit determination results as well as the manoeuvre planning will be emphasised.     

SLUCUBE: Innovative high performance nanosatellite science and technology demonstration mission

The Space Systems Research Laboratory (SSRL) at Saint Louis University is developing SLUCUBE nanosatellite as part of the space mission design program. The objective of the mission is to demonstrate space capability of high performance nanosatellite components that has been developed at SSRL for the past three years. The objective of the program is to provide extremely low-cost and rapid access to space for scientists and commercial exploitation using commercial-off-the-shelf components. SLUCUBE is a double CubeSat with dimensions 10×10×20 cm and a mass of 2 kg. This nanosatellite features suite of technology demonstration components to enlarge the capability of space mission for such class of spacecrafts. The primary mission of SLUCUBE is to test and demonstrate several enabling technologies by flying a number of university developed high performance components. This paper describes the new developed technologies by providing details of specific components developed along with the R&D efforts and laboratory facilities. A brief discussion about the student involvement and educational benefits will also be presented.     

Investigation of nuclear electric powered interstellar precursor missions

Nuclear Electric Propulsion (NEP) is a technology conceptually proposed since the 1940s by E. Stuhlinger in Germany. The JIMO mission originally planned by NASA in the early 2000s produced at least two designs of ion thrusters fed by a 20–30 kW nuclear powerplant. When compared to conventional (chemical) propulsion, the major advantage of NEP in the JIMO context was recognized to be the much higher I_sp (lab-tested at up to 15,000 s) and the capability for sustained power generation, up to 8–10 years when derated to I_sp about 8000 s.The goal of this paper is to show that current or near term NEP technology enables missions far beyond our immediate interplanetary backyard. In fact, by extending the semi-analytical approach used by Stuhlinger, with reasonable ratios α≡power/mass of the propulsion system (i.e., 0.1– 0.4 kW/kg), missions to the Kuiper Belt (40 AU and beyond) and even the so-called FOCAL mission (at 540 AU) become feasible with an attractive payload fraction and in times of order 10–15 years.Further results regarding missions to Sedna’s perihelion/aphelion, and to Oort’s cloud will also be presented, showing the constraints affecting their feasibility and mass budget.     

Endurance testing of a pulsed plasma thruster for nanosatellites

The mission complexity of Nanosatellites has increased tremendously in recent years, but their mission range is limited due to the lack of an active orbit control or ∆v capability. Pulsed Plasma Thrusters (PPT), featuring structural simplicity and very low power consumption are a prime candidate for such applications. However, the required miniaturization of standard PPTs and the adaption to the low power consumption is not straightforward. Most investigated systems have failed to show the required lifetime. The present coaxial design has shown a lifetime of up to 1 million discharges at discharge energies of 1.8 J in previous studies. The present paper focuses on performance characterizations of this design. For this purpose direct thrust measurements with a µN thrust balance were conducted. Thrust measurements in conjunction with mass bit determination allowed a comprehensive assessment. Based on those measurements the present µPPT has a total impulses capability of approximately I≈1.7 Ns, an average mass bit of 0.37 µg s⁻¹ and an average specific impulse of I_sp≈904 s. All tests have shown very good EM compatibility of the PPT with the electronics of the flight-like printed circuit board. Consequently, a complete µPPT unit can provide a ∆v change of 5.1 m/s or 2.6 m/s to a standard 1-unit or 2-unit CubeSat respectively.     

Radiation engineering analysis of shielding materials to assess their ability to protect astronauts in deep space from energetic particle radiation

An analysis is performed on four typical materials (aluminum, liquid hydrogen, polyethylene, and water) to assess their impact on the length of time an astronaut can stay in deep space and not exceed a design basis radiation exposure of 150 mSv. A large number of heavy lift launches of pure shielding mass are needed to enable long duration, deep space missions to keep astronauts at or below the exposure value with shielding provided by the vehicle. Therefore, vehicle mass using the assumptions in the paper cannot be the sole shielding mechanism for long duration, deep space missions. As an example, to enable the Mars Design Reference Mission 5.0 with a 400 day transit to and from Mars, not including the 500 day stay on the surface, a minimum of 24 heavy lift launches of polyethylene at 89,375 lbm (40.54 tonnes) each are needed for the 1977 galactic cosmic ray environment. With the assumptions used in this paper, a single heavy lift launch of water or polyethylene can protect astronauts for a 130 day mission before exceeding the exposure value. Liquid hydrogen can only protect the astronauts for 160 days. Even a single launch of pure shielding material cannot protect an astronaut in deep space for more than 180 days using the assumptions adopted in the analysis. It is shown that liquid hydrogen is not the best shielding material for the same mass as polyethylene for missions that last longer than 225 days.     

Design and testing of a roto-translational shutter mechanism for planetary operation

This work describes the design and testing of a shutter mechanism for a miniaturized infrared spectrometer developed for the ESA ExoMars Pasteur mission. Unlike most usual cover mechanisms, the conceived one provides a roto-translational motion. This feature allows the sealing of the interferometer main entrance window from dust contamination, in addition to the usual function of shuttering the instrument field of view. Although this characteristic is strongly desired because it avoids dust deposition and optics contamination while the instrument is not operating, it makes the mechanism design significantly more complex. Moreover, challenging design constraints were faced: the mass budget allowed for no more than 30 g allocation, the expected working thermal range extended down to −80 °C and high vibration levels with an acceleration peak of 670 m/s² were predicted during Mars landing. To complete the picture, the mechanism cover was required to provide also a calibration target for the 2–25 μm spectral range of the spectrometer. The resulting system is made by a calibrating/shutter cover moved by a purposely designed out of plane cams system which provides the desired motion. A mechanism mockup was assembled and successfully tested in the predicted thermal and mechanical environments.     

On the capabilities of nano electrokinetic thrusters for space propulsion

A theoretical analysis considering the capabilities of nano electrokinetic thrusters for space propulsion is presented. The work describes an electro-hydro-dynamic model of the electrokinetic flow in nano-channels and represents the first attempt to exploit the advantages of the electrokinetic effect as the basis for a new class of nano-scale thrusters suitable for space propulsion. Among such advantages are their small volume, fundamental simplicity, overall low mass, and actuation efficiency. Their electrokinetic efficiency is affected by the slip length, surface charge, pH and molarity. These design variables are analyzed and optimized for the highest electrokinetic performance inside nano-channels. The optimization is done for power consumption, thrust and specific impulse resulting in high theoretical efficiency ∼99% with corresponding high thrust-to-power ratios. Performance curves are obtained for the electrokinetic design variables showing that high molarity electrolytes lead to high thrust and specific impulse values, whereas low molarities provide highest thrust-to-power ratios and efficiencies. A theoretically designed 100 nm wide by 1 μm long emitter optimized using the ideal performance charts developed would deliver thrusts from 5 to 43 μN, specific impulse from 60 to 210 s, and would have power consumption between 1–15 mW. It should be noted that although this is a detail analytical analysis no prototypes exist and any future experimental work will face challenges that could affect the final performance. By designing an array composed of thousands of these single electrokinetic emitters, it would result in a flexible and scalable propulsion system capable of providing a wide range of thrust control for different mission scenarios and maintaining very high efficiencies and thrust-to-power ratio by varying the number of emitters in use at any one time.     

Post mission life plan for FORMOSAT-2

This paper presents the enhancement in mission operations, the mission life state-of-health (SOH) trending analysis, and the post mission life plan of the FORMOSAT-2 (or FS2, Formosa satellite #2, was called ROCSAT-2, or RS2, Republic of China satellite #2, previously) during its five years mission life from 20 May 2004 to 20 May 2009. There are two payloads onboard FS2: a remote sensing instrument (RSI) with nadir ground sampling distance (GSD) of 2 m for panchromatic (PAN) and GSD of 8 m for multi-spectral (MS, 4 bands) as the primary payload, and an imager for sprite and upper atmospheric lightning (ISUAL) as the secondary payload. It was launched on 20 May 2004. The design life is 7 years while the mission life is 5 years. In other words, the end of mission life date of FS2 is 20 May 2009. Generally speaking, FS2 is still at very good condition in its SOH. Post mission life plan for FS2 consists of: the practice of orbit transfer for global coverage and better resolution, the development of gyroless attitude control, and the method for life extension. It is expected that the working life of FS2 can be extended 3–5 years.     

Ultralight deployable booms for solar sails and other large gossamer structures in space

Future solar sail spacecraft which do not need any rocket motors and propellants are a promising option for long-term exploration missions in the solar system. However, they will require ultralight reflective foils and deployable booms which will allow for the unfolding of huge sails. The achievement of an acceptable ratio of reflective sail area and structural mass, which results in a still small, but significant acceleration under the photon pressure of sunlight, is extremely challenging. The same challenging deployment technique is required for the unfolding of large reflector membranes or antennas (gossamer structures). The key elements are the booms which must be stowable in a very small envelope before they reach their destination in space. Such booms were developed by DLR and have been successfully tested under zero-g-conditions during a parabolic flight campaign in February 2009. It could be convincingly demonstrated that the unfolding process is both controllable and reproducible. The booms consisted of two co-bonded omega-shaped carbonfiber half shells with 0.1 mm wall thickness each and had a weight of only 62 g per meter. Two different deployment technologies were tested, one based upon an inflatable 12 μm thick polymer hose inside the boom, the other one using an electromechanical uncoiling device at the tip of each boom. In the latter case, the uncoiling devices will radially fly away from the spacecraft, such that they become “expendable deployment mechanisms” and their mass does not count any more for the spacecraft mass that needs to be accelerated or actively controlled.     

Technology-based design and scaling for RTGs for space exploration in the 100 W range

This paper presents the results of a study on design considerations for a 100 W radioisotope thermo-electric generator (RTG). Special emphasis has been put on designing a modular, multi-purpose system with high overall TRL levels and making full use of the extensive Russian heritage in the design of radioisotope power systems. The modular approach allowed insight into the scaling of such RTGs covering the electric power range from 50 to 200 W_e (EoL). The retained concept is based on a modular thermal block structure, a radiative inner-RTG heat transfer and using a two-stage thermo-electric conversion system.     

Flight performance analysis of GRACE K-band ranging instrument with simulation data

A dual one-way ranging (DOWR) system provides very high accuracy range measurements between two satellites. The GRACE satellite mission implements the DOWR, called KBR (K-band ranging), to measure very small inter-satellite range change in order to map the Earth gravity field. The flight performance of the KBR is analyzed by using a hybrid software simulator that incorporates actual satellite orbit data into a comprehensive KBR simulator, which was earlier used for computing the GRACE baseline accuracy. Three types of experiments were performed. First is the comparison of the flight data with the simulated data in spectral domain. Second is the comparison of double differenced noise level. Third is the comparison of the range-rate difference with GPS clock estimates. The analysis shows a good agreement with the simulation model except some excessive high frequency noise, e.g. 10⁻⁴ m/√Hz at 0.1 Hz. The range-rate difference shows 0.003 cyc/s discrepancy with the clock estimates. These analyses are helpful to refine the DOWR simulation model and can be benefit to future DOWR instrument development.