Spatial Correlation of Reverberation Noise in Active Sonar

A linear array of hydrophones is considered for detecting a signal echo from a stationary target in the presence of reverberation. The structure of the optimum (likelihood ratio) detector is compared with that of a beamformer-matched filter detector. The conditions causing an increase in the spatial noise correlation between two hydrophones are the conditions under which the optimum spatial detector performs significantly better than the beamforming detector. A study of the space-time correlation function of reverberation shows that 1) a decrease in scatterer angular spread (or a narrowing of the receiver directivity pattern) tends to increase the spatial correlation, 2) if the scatterer Doppler spread is much less than the signal carrier frequency and if the angular spread is uniform, it is still possible to get a high correlation if the intersensor distance is much smaller than the carrier wavelength. These conditions indicate situations where optimum techniques may be worthwhile.     

Optimum Signal and Filter Design in Underwater Acoustic Echo Ranging Systems

Optimization of the filter, the signal, and the signal and filter jointly are studied in the sonar environment under noise and reverberation limited conditions. The maximization of the receiver output signal-to-interference ratio is used as a performance criterion with unit energy constraint on both signal and filter. In the filter design problem, the optimum filter function is the solution of a linear integral equation. The kernel of the integral equation is a function of the target and medium scattering functions and the reverberation distribution. In the signal design problem, a similar type of integral equation is obtained as in the filter optimization problem. In the joint signal and filter design problem, it is shown that the optimum signal and filter functions are the solutions to a pair of linear integral equations with the largest (SIR)O. Several examples are investigated for different mediums and reverberation distributions with the finite matrix approximation method. An interative technique is used to compute the joint optimization of signal and filter.     

Optimum Spatial Processing of Passive Sonar Signals

The spatial structure of the likelihood ratio array processor for detecting a monochromatic plane wave signal in Gaussian noise is compared with a conventional beam-forming detector. Conditions are determined under which the optimum detector performs significantly better than the conventional detector. Conditions are also found under which the beamformer is itself near optimal.     

Array shape estimation tracking using active sonar reverberation

This paper concerns the problem of array shape estimation and tracking for towed active sonar arrays, using received reverberation returns from a single transmitted CW pulse. Uniform linear arrays (ULAs) deviate from their nominal geometry while being towed due to ship maneuvers as well as ocean currents. In such scenarios, conventional beamforming performed under the assumption of a ULA can sometimes lead to unacceptably high spatial sidelobes. The reverberation leaking through the sidelobes can potentially mask weak targets in Doppler, especially when the target Doppler is close to that of the mainlobe reverberation and the reverberation-to-target ratio (RTR) is very high. Although heading sensors located along the array can be used to provide shape estimates, they may not be sufficiently available or accurate to provide the required sidelobe levels. We propose an array shape calibration algorithm using multipath reverberation returns from each ping as a distributed source of opportunity. More specifically, a maximum likelihood (ML) array shape calibration algorithm is developed, which exploits a deterministic relationship between the reverberation spatial and Doppler frequencies causing it to be low rank in the space-time vector space formed across a single coherent processing interval (CPI). In this application, a sequence of overlapped CPI length snapshots of duration less than the CW pulse is used. The ML estimates obtained for each snapshot are tracked using a Kalman filter with a state equation corresponding to the water pulley model for array dynamics. Simulations performed using real heading sensor data in conjunction with simulated reverberation suggest that 8-10 dB improvement in sidelobe level may be possible using the proposed array shape tracking algorithm versus an algorithm that uses only the available heading information.     

Mismatched Filtering of Sonar Signals

A replica correlator (matched filter) is an optimum processor for a receiver employing a pulse of continuous wave (CW) signal in a white Gaussian noise background. In an active sonar, however, when the target of interest has low Doppler shift and is embedded in a high reverberation background, this is not so. High sidelobes of the correlator frequency response pass a significant portion of the signal contained in the mainlobe of the reverberation spectrum. In order to reduce the sidelobes of the correlator output spectrum and at the same time keep the increase in its 3 dB bandwidth to a small amount, we propose lengthening of the replica of the transmitted signal and weighting it by a Kaiser window. It is demonstrated that by extending the weighted replica by 50 percent compared with the transmitted signal, it is possible to reduce the sidelobe levels to at least 40 dB below the mainlobe peak, with the concomitant increase of the 3 dB band-width by less than 5 percent. The degradation in signal-to-noise ratio (SNR) performance for such a ?mismatched? filter receiver with respect to the matched filter is less than 1.5 dB.     

Local SNR considerations in decentralized CFAR detection

We consider the decentralized detection problem, involving N sensors and a central processor, in which the sensors transmit unquantized data to the fusion center. Assuming a homogeneous background for constant false-alarm rate (CFAR) analysis, we obtain the performances of the system for the Swerling I and Swerling III target models. We demonstrate that a simple nonparametric fusion rule at the central processor is sufficient for nearly optimum performance. The effect of the local signal-to-noise ratios (SNRs) on the performances of the optimum detector and two suboptimum detectors is also examined. Finally, we obtain a set of conditions, related to the SNRs, under which better performance may be obtained by using decentralized detection as compared with centralized detection     

A localized adaptive MTD processor

The problem of achieving the optimum moving target indicator (MTI) detection performance in strong clutter of unknown spectrum when the set of data available to the estimation of clutter statistics is small due to a severely nonhomogeneous environment is studied. A new adaptive implementation, called the Doppler domain localized generalized likelihood ratio processor (DDL-GLR), is proposed, and its detection performance is studied in detail. It is shown that the DDL-GLR is a data-efficient implementation of the high-order optimum detector and has several advantages of practical importance over the adaptive processors     

Robust detection of small stochastic signals

We consider the problem of detecting a stochastic signal in white not-necessarily-Gaussian noise, using vector valued observations. The locally optimal detector is presented and its performance evaluated. The least-favorable signal spectrum and noise density (over specified classes) are found, and it is shown that the detector using these least-favorable assumptions is minimax robust. The class of spectra is that of any stochastic signal of specified power whose spectrum can be bounded from above and from below by two given positive functions. The class of densities is the ε-contamination model. We present examples of the performance achievable with the robust detector in one of these the spectral uncertainty class corresponds to the unknown Doppler shift of a radar return signal. It is demonstrated that the standard matched-filter's performance degradation with increasing Doppler shift can be avoided almost entirely through use of the robust processor     

Effect of Sampling Time Jitter on Array Performance

The effect on array SNR of errors in sampling times (jitter) isan analyzed for the "Bryn processor." Jitter is modeled as a discrete-paramter er random process, and expressions for array SNR are determined as a function of signal and noise spectra and jitter characteristics. For a plane wave signal, it is found that jitter in the data used to design the processor has no effect on output SNR if the noise is independent between channels. However, jitter in the input (evaluation) n) data can cause a substantial loss in peak array SNR and in the array's frequency selectivity. These losses can be expected to increase as the high-frequency content of the data increases. The Bryn processor also loses its interpretation as a likelihood ratio processor in the presence of jitter. The effect of jitter can be reduced in many cases by increasing the sampling rate.     

Clutter Suppression by Complex Weighting of Coherent Pulse Trains

Uniform coherent pulse trains offer a practical solution to the problem of designing a radar signal possessing both high range and range-rate resolution. The Doppler sensitivity provides some rejection of off-Doppler (clutter) returns in the matched filter receiver. This paper considers the use of a processor in which members of the received pulse train are selectively weighted in amplitude and phase to improve clutter suppression. The techniques described are particularly suitable for rejecting interference entering the processor through ambiguous responses (range sidelobes) of the signal. The complex weights which are derived are optimum in the sense that they produce the maximum clutter suppression for a given detection efficiency. In determining these weights, it is assumed that the distribution of clutter in range and range rate relative to targets of interest is known. Thus, clutter suppression is achieved by reducing the sidelobe levels in specified regions of the receiver response. These techniques are directly applicable to array antennas; the analogous antenna problem would be to reduce sidelobe levels in a particular sector while preserving gain. Complex weighting is most successful when the clutter is limited in both range and velocity.     

Radar Detection of Correlated Targets in Clutter

This paper provides general models of radar echoes from a target. The rationale of the approach is to consider the echoes as the output of a linear dynamic system driven by white Gaussian noise (WGN). Two models can be conceived to generate N target returns: samples generated as a batch, or sequentially generated one by one. The models allow the accommodation of any correlation between pulses and nonstationary behavior of the target. The problem of deriving the optimum receiver structure is next considered. The theory of "estimator-correlator" receiver is applied to the case of a Gaussian-distributed time-correlated target embedded in clutter and thermal noise. Two equivalent detection schemes are obtained (i. e., the batch detector and the recursive detector) which are related to the above mentioned procedures of generating radar echoes. A combined analytic-numeric method has been conceived to obtain a set of original detection curves related to operational cases of interest. Finally, an adaptive implementation of the proposed processor is suggested, especially with reference to the problem of on-line estimation of the clutter covariance matrix and of the CFAR threshold. In both cases detection loss due to adaptation has been evaluated by means of a Monte Carlo simulation approach. In summary, the original contributions of the paper lie in the mathematical formulation of a powerful model for radar echoes and in the derivation of a large set of detection curves.     

Detection of weak, subpixel targets using mesh-connected cellularautomata

Effective use of military cellular automata such as military data array processor (MilDAP) and geometric arithmetic parallel processor (GAPP), in weak, subpixel target detection is shown to be possible by using new signal processing regimes based on binary ranking filter theory. By using binary ranking filters, the MilDAP can furnish 6 dB of processing gain against white Gaussian noise while monitoring from one to four million potential target tracks at 10-40 frames/s. GAPP is shown to be capable of monitoring 3.7 million tracks over 216×384 detectors at 14000 frames/s and, in a time sharing mode, 15 million tracks over 432×768 detectors at 24 frames/s. The special case of threatening targets is discussed, as well as alternate cellular architectures which use multidimensional binary ranking filters in multidimensional coordinate systems     

Automated Tracking for Aircraft Surveillance Radar Systems

An improved moving target detector (MTD) (a digital signal processor) has been designed, constructed, and tested which successfully rejects all forms of radar clutter while providing reliable detection of all aircraft within the coverage of the radar. The MTD is being tested on both terminal and enroute surveillance radars for the FAA. This processor has been integrated with automatic tracking algorithms to give complete rejection of ground clutter, heavy precipitation, and angels (birds).     

Optimum detection and location estimation of target lines in the range-time space of a search radar

The average likelihood ratio detector is derived as the optimum detector for detecting a target line with unknown normal parameters in the range-time data space of a search radar, which is corrupted by Gaussian noise. The receiver operation characteristics of this optimum detector is derived to evaluate its performance improvement in comparison with the Hough detector, which uses the return signal of several successive scans to achieve a non-coherent integration improvement and get a better performance than the conventional detector. This comparison, which is done through analytic derivations and also through simulation results, shows that the average likelihood ratio detector has a better performance for different SNR values. This result is justified by showing the disadvantages of the Hough method, which are eliminated by the optimum detector. To have an estimate for the location of the detected target line in the optimum detection method as the Hough method, which detects and localizes the target lines simultaneously, we present the maximum a posteriori probability estimator. The estimation performance of the two methods is then compared and it is shown that the maximum a posteriori probability estimator localizes the detected target lines with a better performance in comparison with the Hough method.     

A CFAR adaptive matched filter detector

An adaptive algorithm for radar target detection using an antenna array is proposed. The detector is derived in a manner similar to that of the generalized likelihood-ratio test (GLRT) but contains a simplified test statistic that is a limiting case of the GLRT detector. This simplified detector is analyzed for performance to signals on boresight, as well as when the signal direction is misaligned with the look direction     

相控阵雷达捷联波束稳定方法

针对相控阵雷达系统中平台扰动引起的波束指向变化问题,提出一种捷联波束稳定方法。该方法作为独立模块实现,由角速度传感器和信号处理机组成,无需精确的初始姿态。角速度传感器感知平台扰动造成的天线转动角速度,信号处理机完成补偿角的迭代求解和波束的控制。通过算法仿真和利用单轴转台模拟平台扰动验证可得,采用捷联波束稳定方法后,雷达测量角误差明显减小,隔离度指标有了极大改善。因此,该方法能够有效地减小平台扰动对波束指向的影响,易于工程实现,适用于小型化的无人机等平台。     

Sonar Array Detection of Gaussian Signals in Gaussian Noise of Unknown Power

A statistical test is postulated for detecting, with an M-element hydrophone array, a Gaussian signal in spatially independent Gaussian noise of unknown power. The test is an extension of the uniformly-most-powerful (UMP) unbiased test for a two-element array. The output signal-to-noise ratio of the test is calculated and, for a large number of independent space-time samples, is shown to be no better than a mean-level detector (MLD). Receiver operating characteristic curves (ROC) for the MLD are computed and compared to the ROC curves for the optimum (Bayes) parametric detector. The input signal-to-noise power ratios required to provide a detection probability of 0.5 differ by less than 0.2 dB for a fifty-element array with wide variation in false-alarm probability and time-bandwidth product. This result suggests that both the extended bivariate UMP unbiased test and the MLD perform close to the unknown UMP unbiased test for independence of a multivariate Gaussian distribution.     

Vector subspace detection in compound-Gaussian clutter. Part I: survey and new results

Deals with the problem of detecting subspace random signals against correlated non-Gaussian clutter exploiting different degrees of knowledge on target and clutter statistical characteristics. The clutter process is modeled by the compound-Gaussian distribution. In the first part of the paper, the optimum Neyman-Pearson (NP) detector, the generalized likelihood ratio test (GLRT), and a constant false-alarm rate (CFAR) detector are sequentially derived both for the Gaussian and the compound-Gaussian scenarios. Different interpretations of the various detectors are provided to highlight the relationships and the differences among them. In particular, we show how the GLRT detector may be recast into an estimator-correlator form and into another form, namely a generalized whitening-matched filter (GWMF), which is the GLRT detector against Gaussian disturbance, compared with a data-dependent threshold. In the second part of this paper, the proposed detectors are tested against both simulated data and measured high resolution sea clutter data to investigate the dependence of their performance on the various clutter and signal parameters.     

Multipath Angle Error Reduction Using Multiple-Target Methods

The usual methods of reducing multipath angle errors in monopulse tracking radar achieve only limited success because they do not attack the root of the problem. A more correct approach is to accept the multipath signal as a second target and utilize a two-target signal processor which angle tracks both wavefronts. The processor will decouple the return signals so that relatively interference-free data on both waves are obtained. In this paper a signal processor for separating signal from (N - 1) multipath components is developed. The processor is then specialized to the case of only one multipath signal and evaluated by a computer simulation. Data show that large improvements are possible as compared to the usual monopulse tracking system. In particular, the usual large bias errors at low elevation angles are eliminated. Tracking precision compares favorably with the theoretically best possible for two-target tracking systems.     

Array Processor Performance Under Directional Uncertainty

Detection performance of four candidate receiver structures for the signal known except for direction (SKED) array problem is investigated. Included are the Bayes optimal detector, two estimate and plug structures, and a fixed estimate structure. Estimators considered are the maximum likelihood (ML) and maximum a posteriori (MAP). Performance degradation from optimal for the estimate and plug structures considered is shown to be significantly more severe the larger the array size.