UV 波段的宽带可重构收发机的实现

设计了一种宽带可重构收发机,主要由三部分组成：发射机、接收机和频率源。发射机完成从中频 70 MHz 到100~550 MHz 的射频发射,为了减小发射信号对相邻信道的干扰,发射信号的杂散抑制要高。接收 机从众多的电波中选出有用信号,并将该信号搬移到中频信号,然后放大到解调器所要求的电平值,将射频信 号变为中频信号,由于传输路径上的损耗和多径效应,接收机接收的信号是微弱且有变化的,并伴随着许多干 扰,这些干扰信号强度往往远大于有用信号,因此接收机的主要指标是灵敏度和选择性。频率源提供精确和低 噪声的本振信号,为射频变频系统核心部分之一,频率源的主要指标是相位噪声。     

数字闭环光纤陀螺的调制串扰误差

 通过分析数字闭环光纤陀螺的阶梯波调制信号与输出死区、周期噪声干扰及小角速度漂移的关系,提出了调制串扰误差的概念。指出调制信号与探测器输出信号之间的电交叉耦合及调制信号产生的调制误差是产生调制串扰误差的干扰源。将调制串扰通道模型简化为比例环节和部分积分环节,并和光纤陀螺理想模型结合,建立了光纤陀螺调制串扰误差模型,利用该模型推导出了产生死区的条件及周期噪声干扰和小角速度漂移造成的输出偏差表达式,并对周期噪声的幅值、频率与陀螺输出量级、带宽之间的关系进行了定量分析。调制串扰误差的仿真和实验结果与理论分析结果基本一致,验证了调制串扰误差模型的正确性。     

Area Target Response of Triangularly Frequency-Modulated Continuous-Wave Radars

For a postulated model of the area target returns, the variance of the signal appearing at the detector output of a frequency-modulated continuous-wave radar is analytically and graphically displayed as a function of the range and Doppler spread. The influence of important system parameters like modulation frequency, measuring time, and frequency excursion are also included in the analysis. Closedform relationships are given for sawtooth or triangular frequency modulation and a Gaussian separable scattering function. A comparison is also made between the range noise of an ideal frequency detector and a zero-crossings counter.     

一种新的无人机数据链抗干扰技术研究(英文)

Based on the M-ary spread spectrum （M-ary-SS）, direct sequence spread spectrum （DS-SS）, and orthogonal frequency division multiplex （OFDM）, a novel anti-jamming scheme, named orthogonal code time division multi-subchannels spread spectrum modulation （OC-TDMSCSSM）, is proposed to enhance the anti-jamming ability of the unmanned aerial vehicle （UAV） data link. The anti-jamming system with its mathematical model is presented first, and then the signal formats of transmitter and receiver are derived. The receiver＇s bit error rate （BER） is demonstrated and anti-jamming performance analysis is carded out in an additive white Ganssian noise （AWGN） channel. Theoretical research and simulation results show the anti-jamming performance of the proposed scheme better than that of the hybrid direct sequence frequency hopping spread spectrum （DS/FH SS） system. The jamming margin of the OC-TDMSCSSM system is 5 dB higher than that of DS/FH SS system under the condition of Rician channel and full-band jamming, and 6 dB higher under the condition of Rician channel environment and partial-band jamming.     

一种基于TDDM裂谱信号的解模糊位搜索法

时分数据调制(TDDM)裂谱信号作为一种新调制信号,具有独有的电文翻转位模糊特性,导致了采用通常的搜索方法无法正确输出电文的现象。针对TDDM裂谱信号特性以及现有搜索方法的不足,提出了一种解模糊位搜索法。该方法主要分为合路快捕及解模糊位判决两个阶段。其合路快捕阶段,不但可以快速缩小搜索范围,而且可以避免由扩频方式而引起的漏捕现象;解模糊位判决阶段,可以去除电文翻转位的模糊度,正确输出电文的翻转位置。在理论推导的基础上,从性能及信噪比容限角度进行了仿真测试,测试结果表明,解模糊位搜索法对TDDM裂谱信号的电文翻转位判决精度可以达到100%。     

噪声调制连续波雷达信号波形射频隐身特性

雷达信号波形的射频(RF)隐身性能是雷达系统能否适应现代战场环境的重要因素,雷达射频隐身信号波形设计是现代雷达系统设计中的重要课题.首先,在介绍随机噪声信号雷达原理的基础上,基于Schleher截获因子阐述了噪声调制连续波雷达信号波形的射频隐身特性.然后,分析了高斯噪声相位和频率调制连续波雷达输出自相关函数和高斯噪声相...     

Interferences in Phase-Locked Loops

An analysis of the behavior of a second-order phase-locked loop is presented when an unwanted signal is added to the useful signal. Both signals are sinusoidal and unmodulated, and the analysis is made in the absence of additive noise. When the loop remains locked on the useful signal, a parasitic signal exists at the phase detector output. This signal produces a parasitic phase modulation of the VCO and a static phase error in the loop. The parasitic signal amplitude, the parasitic phase modulation index, and the static phase error are calculated. A necessary condition for the loop to remain in lock is derived. When the loop is initially unlocked, locking can occur either on the useful signal or on the unwanted signal, depending on the amplitude ratio and the frequency difference of the two signals. A formula allowing one to compute the pull-in time is obtained. When the loop locks on the useful signal, acquisition can be slower or faster than in the absence of an unwanted signal. The same phenomenon is observed when the loop locks on the unwanted signal.     

基于DDS+PLL的光源调制与功率稳定控制方法CSCD

量子传感器是基于量子操控技术的研究成果,一般具有高精度、小体积等优势。激光器是量子传感器的核心部件,有抽运和检测功能,激光器的稳定性对量子传感器具有重要的意义。提出了一种直接数字合成法(DDS)与锁相回路(PLL)相结合的方法,对激光器进行调制并抑制调制噪声,实现了激光器的稳定输出。基于现有小型量子传感器装置,在DDS生成4kHz参考信号的情况下实现了激光器电流8kHz调制,抑制了调制时调制电流信号噪声约8dB,并提高了激光器输出光功率的稳定性。     

FM/AM Noise Test Set for a Pulsed Doppler Radar

A new test method to measure the amplitude noise and phase noise in both CW and pulsed CW signals of a Ku-band pulsed Doppler radar is described. These noises are measured in a simulated environment of radar operation; thus the test results may give direct information to determine radar subclutter visibility. In comparison with the conventional noise test method, this new method not only gives more meaningful results but also can obtain results much faster in testing. Actual test system design is described by block diagrams and theoretical analysis. A method to determine approximate frequency jitter in a transmitter signal is also described.     

高频振荡器噪声分析

 本文将高频振荡器视为具有深度正反馈噪声放大器。对它分析,给出正弦波信号的谱、等效带宽及相位噪声谱;同时还提出诸如高频振荡器内部产生的随机游走噪声形成机理等新看法。     

基于MED和LMD的自动倾斜器轴承广义Shannon熵谱分析

针对轴承信号微弱故障特征易被强背景噪声淹没的问题,提出采用最小熵反褶积,通过逆滤波器最优化设计,对目标信号进行降噪处理,其峭度值提高了约3.8倍,增强了信号的微弱故障特征;针对非平稳非线性信号频率成分复杂难以解调的问题,提出采用局部均值分解(LMD)和峭度-相关系数筛选准则,其可对非平稳非线性信号进行自适应分解和最优重构,提高了信号的信噪比;针对信号耦合调制及边频突出的问题,通过引入广义Shannon熵进行包络谱带内降噪处理,信号一阶故障特征调制频率与故障特征频率的幅度比降低了24%~43%。通过实验室信号及某型直升机自动倾斜器轴承故障诊断地面试验的分析结果验证了该方法的合理性和可行性。      

The Effect of Hard Limiting an Angle-Modulated Signal Plus Noise

The effect of hard limiting an angle-modulated signal plus narrow-band Gaussian noise is analyzed. Several examples are considered?sinusoidal angle modulation, Gaussian angle modulation, and biphase angle modulation. The general conclusion is that when a zonal band-pass filter is used, which rejects dc and second harmonics, an angle-modulated signal plus Gaussian noise provides the same output signal-to-noise ratio as shown by Davenport for a CW signal plus Gaussian noise. However, when a narrow bandpass filter is used, which has a bandwidth approximately equal to the input angle-modulated signal, an angle-modulated signal plus Gaussian noise has a better output signal-to-noise ratio than a CW signal plus Gaussian noise.     

Error Analysis for Relay Type Satellite-Aided Search and Rescue Systems

An analysis is made of the errors in the determination of the position of an emergency transmitter in a satellite-aided search and rescue system. The satellite is assumed to be at a height of 820 km in a near-circular near polar orbit. Short data spans of four minutes or less are used. The error sources considered are measurement noise, transmitter frequency drift, ionospheric effects, and error in the assumed height of the transmitter. The errors are calculated for several different transmitter positions, data rates, and data spans. The only transmitter frequency used was 406 MHz, but the result can be scaled to different frequencies.     

Pseudorandom Frequency Modulation in Range-Doppler Radar

In many radar systems, efficient use of transmitter power requires the transmission of a constant-amplitude signal for a substantial fraction of time; for a monotonic transmission, however, the range resolution is restricted by the length of the transmitted pulse. Linear frequency modulation removes this constraint for targets with negligible, or known, radial velocities; it is not suitable, however, for simultaneous observations of range and radial velocity (Doppler shift). This paper describes a class of waveforms suitable for simultaneous measurement of range and Doppler shift. These waveforms are characterized by a uniform distribution in frequency and by pseudorandom frequency changes. Uniform frequency distribution is attained by a uniform spacing of frequencies with each frequency present for an identical length of time. Frequency changes are effected by sequencing the frequencies with a pseudorandom number generator. Ambiguity functions are computed for pseudorandom frequencymodulated waveforms designed for ionospheric backscatter studies. By suitable choice of parameters, the ambiguity function becomes a narrow central peak surrounded by a plateau whose height varies randomly between zero and approximately twice its average. Waveform generation by means of a digital frequency synthesizer and data reconstruction considerations are described.     

Single Channel Per Carrier Satellite Repeater Channel Capacity

This paper analyzes the performance of a number of modulation and speech processing techniques that have been considered for single voice channel per carrier transmissions via satellite. This transmission mode is applicable to demand assignment systems, which make possible the most efficient loading of the satellite transponder in applications where the traffic at individual Earth terminals is not sufficient to justify a substantial number of dedicated channels. The analysis basically determines the operating point for the satellite transponder which minimizes the required Earth terminal G/T. The fraction of the total link noise allocated to uplink noise is treated as a parameter, so that the cost of improving G/T may be traded against the cost of providing increased Earth terminal transmitter power. Both analog and digital modulation techniques are considered, together with various practical combinations of syllabic companding, voice-actuated carriers, and error-correcting codes. The results are presented in general analytic form, applicable to any modulation technique for which carrier-to-noise density ratio, channel width, and guardband width may be specified. Curves showing required G/T as a function of the total number of voice channels per transponder are also presented for the above-mentioned signal processing techniques, assuming "CCIR/CITT type" speech quality and transponder EIRP and bandwidth typical of current domestic satellite configurations.     

Two Methods of Spectral Estimation for SARSAT Signals

Search and rescue satellite aided tracking (SARSAT) depends on the processing of emergency locator transmitter (ELT) signals which are received by a satellite in low polar orbit. Since the signal from a distressed vehicle is normally immersed in a background of other ELT signals (false alarms), interference, and noise, different methods of spectral estimation can provide advantages in estimating carrier frequency. A comparison between average spectrum and minimum spectrum for several real signals is provided here.     

Spectral Analysis of ELT Signals for SARSAT

Search and rescue satellite-aided tracking (SARSAT) relays the emergency locator transmitter (ELT) signals of distressed aircraft to an earth station for spectral analysis. Of considerable importance are the characteristics of the spectrum of the ELT signal since the probability of locating the downed aircraft is closely related to the quality of the ELT signal spectrum itself. In this paper, it is shown that the spectrum can be adversely affected by a number of factors including the phase and frequency characteristics of the carrier and their interaction with the amplitude modulation. Two new models are proposed which greatly reduce the self-generated interference produced by ELT units presently being used.     

406 MHz ELT signal spectra for SARSAT

The signal format and spectral properties of the 406-MHz emergency locator transmitter (ELT) used in the search and rescue satellite aided tracking (SARSAT) system are examined. The ELT improves location estimate accuracies and can relay information about the particular aircraft and its problem, by means of the digitally modulated message fields. It is shown that due to the RF signal frequency characteristics and the Doppler shift, processing must be performed over a frequency band of approximately 25 kHz. Through the use of the fast Fourier transformation (FFT), the frequency spectrum of the ELT is analyzed, taking account of effects due to noise, multiple simultaneously received signals, and Doppler shift. It is demonstrated that the FFT provides an effective means for detecting and recognizing the presence of one or more ELT signals over this 25-kHz frequency band. Some recommendations are made to improve the spectral characteristics and the performance of the ELT     

Some Matched Filter Configurations for Infrared Systems

An analysis of the output of three alternative matched filter configurations in an infrared scanning system model is presented. The sensor is corrupted by thermal noise, generation-recombination noise, photon noise, and modulation noise, the latter providing an extreme discoloration in the signal passband. Expressions for the signal voltage density spectrum, signal pulse shape, noise power spectrum, and average noise power at the matched filter output are derived where the integral evaluations attendant to these derivations do not appear elsewhere in the literature. The paper also provides graphical displays of the signal-to-noise power ratio at the filter output versus various system parameters, noise power spectrum out of the matched filter versus ?, and the signal pulse shape out of the filter versus time. Also included are discussions of practically realizable approximations to the matched filters and curve fitting techniques for the signal pulse shape function.     

Ultrawideband microwave-radar conceptual design

This paper outlines the special considerations that characterize the design of an UWB radar for the detection of low-altitude missiles over the sea. It discusses the factors which enter into the choice of frequency, and the selection of the transmitter, antenna, and receiver. Reviewed are signal processing issues concerning detection of UWB signals in noise and clutter, nondoppler MTI based on the pulse-to-pulse change in range due to target motion, measurement of target height based on multipath time delay, and target recognition. As the investigation progressed, the authors became disappointed with the available UWB technology, but encouraged about the potential advantages of UWB for this application. The chief limitation of UWB radar that must be overcome before applications are viable is its poor electromagnetic compatibility (EMC)