Controlled Ecological Life Support Systems (CELSS) flight experimentation.

The NASA CELSS program has the goal of developing life support systems for humans in space based on the use of higher plants. The program has supported research at universities with a primary focus of increasing the productivity of candidate crop plants. To understand the effects of the space environment on plant productivity, the CELSS Test Facility (CTF) has been been conceived as an instrument that will permit the evaluation of plant productivity on Space Station Freedom. The CTF will maintain specific environmental conditions and collect data on gas exchange rates and biomass accumulation over the growth period of several crop plants grown sequentially from seed to harvest. The science requirements of the CTF will be described, as will current design concepts and specific technology requirements for operation in micro-gravity.     

Subcritical and supercritical water oxidation of CELSS model wastes.

Controlled-Ecological-Life-Support-System (CELSS) model wastes were wet-oxidized at temperatures from 250 to 500 degrees C, i.e., below and above the critical point of water (374 degrees C and 218 kg/cm2 or 21.4 MPa). A solution of ammonium hydroxide and acetic acid and a slurry of human urine, feces, and wipes were used as model wastes. Almost all of the organic matter in the model wastes was oxidized in the temperature range from 400 to 500 degrees C, i.e., above the critical conditions for water. In contrast, only a small portion of the organic matter was oxidized at subcritical conditions. Although the extent of nitrogen oxidation to nitrous oxide (N2O) and/or nitrogen gas (N2) increased with reaction temperature, most of the nitrogen was retained in solution as ammonia near 400 degrees C. This important finding suggests that most of the nitrogen in the waste feed can be retained in solution as ammonia during oxidation at low supercritical temperatures and be subsequently used as a nitrogen source for plants in a CELSS while at the same time organic matter is almost completely oxidized to carbon dioxide and water. It was also found in this study the Hastelloy C-276 alloy reactor corroded during waste oxidation. The rate of corrosion was lower above than below the critical temperature for water.     

BIOS-4 as an embodiment of CELSS development conception.

Any attempt to create LSS for practical applications must take into account the possibility of castastrophic consequences if the problem of LSS reliability and stability is not solved. An integrated conception of CELSS studies development as a possible way to increase its reliability is considered. The BIOS-4 facility project is developed in the context of the conception. Three principles of highly effective experimental CELSS facility design are proposed. Some details of BIOS-4 design and its exploitation features are presented.     

Performance of the CELSS Antarctic Analog Project (CAAP) crop production system.

Regenerative life support systems potentially offer a level of self-sufficiency and a decrease in logistics and associated costs in support of space exploration and habitation missions. Current state-of-the-art in plant-based, regenerative life support requires resources in excess of allocation proposed for candidate mission scenarios. Feasibility thresholds have been identified for candidate exploration missions. The goal of this paper is to review recent advances in performance achieved in the CELSS Antarctic Analog Project (CAAP) in light of the likely resource constraints. A prototype CAAP crop production chamber has been constructed and operated at the Ames Research Center. The chamber includes a number of unique hardware and software components focused on attempts to increase production efficiency, increase energy efficiency, and control the flow of energy and mass through the system. Both single crop, batch production and continuous cultivation of mixed crops production studies have been completed. The crop productivity as well as engineering performance of the chamber are described. For each scenario, energy required and partitioned for lighting, cooling, pumping, fans, etc. is quantified. Crop production and the resulting lighting efficiency and energy conversion efficiencies are presented. In the mixed-crop scenario, with 27 different crops under cultivation, 17 m2 of crop area provided a mean of 515 g edible biomass per day (85% of the approximate 620 g required for one person). Enhanced engineering and crop production performance achieved with the CAAP chamber, compared with current state-of-the-art, places plant-based life support systems at the threshold of feasibility.     

Significance of rhizosphere microorganisms in reclaiming water in a CELSS.

Plant-microbe interactions, such as those of the rhizosphere, may be ideally suited for recycling water in a Controlled Ecological Life Support System (CELSS). The primary contaminant of waste hygiene water will be surfactants or soaps. We identified changes in the microbial ecology in the rhizosphere of hydroponical1y grown lettuce during exposure to surfactant. Six week old lettuce plants were transferred into a chamber with a recirculating hydroponic system. Microbial density and population composition were determined for the nutrient solution prior to introduction of plants and then again with plants prior to surfactant addition. The surfactant Igepon was added to the recirculating nutrient solution to a final concentration of 1.0 g L-1. Bacteria density and species diversity of the solution were monitored over a 72-h period following introduction of Igepon. Nine distinct bacterial types were identified in the rhisosphere; three species accounted for 87% of the normal rhizosphere population. Microbial cell number increased in the presence of Igepon, however species diversity declined. At the point when Igepon was degraded from solution, diversity was reduced to only two species. Igepon was found to be degraded directly by only one species found in the rhizosphere. Since surfactants are degraded from the waste hygiene water within 24 h, the potential for using rhizosphere bacteria as a waste processor in a CELSS is promising.     

Use of biologically reclaimed minerals for continuous hydroponic potato production in a CELSS.

Plant-derived nutrients were successfully recycled in a Controlled Ecological Life Support System (CELSS) using biological methods. The majority of the essential nutrients were recovered by microbiologically treating the plant biomass in an aerobic bioreactor. Liquid effluent containing the nutrients was then returned to the biomass production component via a recirculating hydroponic system. Potato (Solanum tuberosum L.) cv. Norland plants were grown on those nutrients in either a batch production mode (same age plants on a nutrient solution) or a staggered production mode (4 different ages of plants on a nutrient solution). The study continued over a period of 418 days, within NASA Breadboard Project's Biomass Production Chamber at the Kennedy Space Center. During this period, four consecutive batch cycles (104-day harvests) and 13 consecutive staggered cycles (26-day harvests) were completed using reclaimed minerals and compared to plants grown with standard nutrient solutions. All nutrient solutions were continually recirculated during the entire 418 day study. In general, tuber yields with reclaimed minerals were within 10% of control solutions. Contaminants, such as sodium and recalcitrant organics tended to increase over time in solutions containing reclaimed minerals, however tuber composition was comparable to tubers grown in the control solutions.     

Development of a CELSS bioreactor: oxygen transfer and micromixing in parabolic flight.

The gas exchange portion of a phase-separated loop bioreactor was tested with respect to oxygen mass transfer and micromixing in accelerations of 0.01g, 1g, and 2g. A plot of the overall mass transfer coefficient versus gravity indicates the rate of oxygen transfer does not change as a function of acceleration. Also, it was determined that the micromixing did not exhibit significant changes in the various gravitational fields. These observations indicate the loop bioreactor should function independent of acceleration.     

Carbon balance and productivity of Lemna gibba, a candidate plant for CELSS.

The photosynthesis and productivity of Lemna gibba were studied with a view to its use in Controlled Ecological Life Support Systems (CELSS). Photosynthesis of L. gibba floating on the nutrient solution could be driven by light coming from either above or below. Light from below was about 75% as effective as from above when the stand was sparse, but much less so with dense stands. High rates of photosynthesis (ca. 800 nanomoles CO2 g dry weight (DW)-1 s-1) were measured at 750 micromoles m-2 s-1 PPF and 1500 micromoles mol-1 CO2. This was attained at densities up to 660 g fresh weight (FW) m-2 with young cultures. After a few days growth under these conditions, and at higher densities, the rate of photosynthesis dropped to less than 25% of the initial value. This drop was only partly alleviated by thinning the stand or by introducing a short dark period at high temperature (26 degrees C). Despite the drop in the rate of photosynthesis, maximum yields were obtained in batch cultures grown under continuous light, constant temperature and high [CO2]. Plant protein content was less than reported for field grown Lemna. When the plants were harvested daily, maintaining a stand density of 600 g FW m-2, yields of 18 g DW m-2 d-1 were obtained. The total dry weight of L. gibba included 40% soluble material (sugars and amino acids), 15% protein, 5% starch, 5% ash and 35% cellulose and other polymers. We conclude that a CELSS system could be designed around stacked, alternate layers of transparent Lemna trays and lamps. This would allow for 7 tiers per meter height. Based on present data from single layers, the yield of such a system is calculated to be 135 g DW m-3 d-1 of a 100% edible, protein-rich food.     

The C23A: first step to a monitoring system of CELSS in flight.

Studies for every level of CELSS: Waste processing, food production, photosynthesis system, and so on ..., imply an automatic system to control, command and quantify gases, water and chemical compounds. Used for many years in plant physiology studies, the C23A system monitors the analysis and quantifies gases (O2, CO2. N2, ...), physical parameters (temperature, humidity, ...) and chemical compounds (NH4+, N03-, ...) on numerous experiments. In the new version, the architecture of the computing system is near of the space requirements. We have chosen a structure with three independent levels: acquisition, monitoring and supervision. Moreover, we use multiplexed analysers: IRGA, mass spectrometer and cheminal analyser. The multiplexing increases the accuracy of the measurements and could facilitate the spatialization. Thus the whole structure anticipates the entire separation between automation in space and control-command on ground.     

The effect of radiation on the long term productivity of a plant based CELSS.

Mutations occur at a higher rate in space than under terrestrial conditions, primarily due to an increase in radiation levels. These mutations may effect the productivity of plants found in a controlled ecological life support system (CELSS). Computer simulations of plants with different ploidies, modes of reproduction, lethality thresholds, viability thresholds and susceptibilities to radiation induced mutations were performed under space normal and solar flare conditions. These simulations identified plant characteristics that would enable plants to retain high productivities over time in a CELSS.     

Mass balances for a biological life support system simulation model.

Design decisions to aid the development of future space-based biological life support systems (BLSS) can be made with simulation models. Here we develop the biochemical stoichiometry for 1) protein, carbohydrate, fat, fiber, and lignin production in the edible and inedible parts of plants; 2) food consumption and production of organic solids in urine, feces, and wash water by the humans; and 3) operation of the waste processor. Flux values for all components are derived for a steady-state system with wheat as the sole food source. The large-scale dynamics of a materially-closed (BLSS) computer model is described in a companion paper. An extension of this methodology can explore multi-food systems and more complex biochemical dynamics while maintaining whole-system closure as a focus.     

A new dynamical atmospheric ionizing radiation (AIR) model for epidemiological studies.

A new Atmospheric Ionizing Radiation (AIR) model is currently being developed for use in radiation dose evaluation in epidemiological studies targeted to atmospheric flight personnel such as civilian airlines crewmembers. The model will allow computing values for biologically relevant parameters, e.g. dose equivalent and effective dose, for individual flights from 1945. Each flight is described by its actual three dimensional flight profile, i.e. geographic coordinates and altitudes varying with time. Solar modulated primary particles are filtered with a new analytical fully angular dependent geomagnetic cut off rigidity model, as a function of latitude, longitude, arrival direction, altitude and time. The particle transport results have been obtained with a technique based on the three-dimensional Monte Carlo transport code FLUKA, with a special procedure to deal with HZE particles. Particle fluxes are transformed into dose-related quantities and then integrated all along the flight path to obtain the overall flight dose. Preliminary validations of the particle transport technique using data from the AIR Project ER-2 flight campaign of measurements are encouraging. Future efforts will deal with modeling of the effects of the aircraft structure as well as inclusion of solar particle events.     

Biodegradation pathway of an anionic surfactant (Igepon TC-42) during recycling waste water through plant hydroponics for advanced life support during long-duration space missions.

The degradation of an anionic surfactant (Igepon TC-42) was investigated as part of an integrated study of direct recycling of human hygiene water through hydroponic plant growth systems. Several chemical approaches were developed to characterize the degradation of Igepon and to measure the accumulation of intermediates such as fatty acids and methyl taurine. Igepon was rapidly degraded as indicated by the reduction of methylene blue active substances (MBAS) and component fatty acids. The Igepon degradation rate continued to increase over a period of several weeks following repeated daily exposure to 18 micrograms/l Igepon. The accumulation of free fatty acids and methyl taurine was also observed during decomposition of Igepon. The concentration of methyl taurine was below detection limit (0.2 nmol/ml) during the slow phase of Igepon degradation, and increased to 1-2 nmol/ml during the phase of rapid degradation. These findings support a degradation pathway involving initial hydrolysis of amide to release fatty acids and methyl taurine, and subsequent degradation of these intermediates.     

Experimental simulation of proton space radiation environments: a dosimetric perspective.

Three-dimensional dose calculation techniques developed for radiotherapy treatment planning were used to calculate dose distributions from unidirectional, planar rotational and omnidirectional incident radiation (experimental proton beams and solar flares). The calculations predicted regions of high dose within primate heads exposed to 55-MeV protons, supporting the postulate of radiation-induced brain tumors within this population. Comparisons among predicted doses to the human head from solar flares of three different energies demonstrated differences between unidirectional and omnidirectional irradiation in the space environment. The results can be used to estimate dose distributions based on a) limited phantom measurements, or b) nonuniformly incident radiation in orbit; both situations are difficult to replicate under laboratory exposure conditions.     

C.E.B.A.S. MINI MODULE: test results of an artificial (man-made) aquatic ecosystem.

The original Closed Equilibrated Biological Aquatic System (C.E.B.A.S.) is a long-term multi-generation research facility for experiments with aquatic animals and plants in a space station the development of which is surrounded by a large international scientific program. In addition, a miniaturized laboratory prototype, the C.E.B.A.S. MINI MODULE, with a total volume of about 10-12 liters for a Spacelab middeck locker was developed and a first version was tested successfully for two weeks with a population of fishes (Xiphophorus helleri) in the animal tank and a Ceratophyllum spec. in the illuminated higher plant growth chamber. The water recycling system consisted of a bacteria filter and a mechanical filter and the silastic tubing gas exchanger was separated by valves for the utilization in emergency cases only. Data were collected with the acquisition module of the original C.E.B.A.S. process control system. In addition, an optimized version was tested for 7 weeks with fishes and plants and thereafter with fish and with plants only for 2 and 1 weeks, resp.. The paper presents the relevant water parameters (e.g., pH, pressure, temperature, oxygen saturation, flow rate, ion concentrations) during the test period as well as morphological and physiological data of the enclosed animals and plants. On the basis of the given results the possible role of the C.E.B.A.S. system as a scientific tool in artificial ecosystem research and for the development of a combined animal-plant intensive aquaculture system and its utilization in bioregenerative life support is discussed.     

Performance of a simple Closed Aquatic Ecosystem (CAES) in space.

A simple Closed Aquatic Ecosystem (CAES) consisting of single-celled green algae (Chlorella pyrenoidosa, producer), a spiral snail (Bulinus australianus, consumer) and a data acquisition and control unit was flown on the Chinese Spacecraft SHENZHOU-II in January 2001 for 7 days. In order to study the effect of microgravity on the operation of CAES, a 1 g centrifuge reference group in space, a ground 1 g reference group and a ground 1 g centrifuge reference group (1.4 g group) were run concurrently. Real-time data about algae biomass (calculated from transmission light intensity), temperature, light and centrifugation of the CAES were logged at minute intervals. It was found that algae biomass of both the microgravity group and the ground 1 g-centrifuge reference group (1.4 g) fluctuated during the experiment, but the algae biomass of the 1 g centrifuge reference group in space and the ground 1 g reference group increased during the experiment. The results may be attributable to influences of microgravity and 1.4 g gravity on the algae and snails metabolisms. Microgravity is the main factor to affect the operation of CAES in space and the contribution of microgravity to the effect was also estimated. These data may be valuable for the establishment of a complex CELSS in the future.     

Displacement monitoring performance of relative positioning and Precise Point Positioning (PPP) methods using simulation apparatus

Besides the classical geodetic methods, GPS (Global Positioning System) based positioning methods are widely used for monitoring crustal, structural, ground etc., deformations in recent years. Currently, two main GPS positioning methods are used: Relative and Precise Point Positioning (PPP) methods. It is crucial to know which amount of displacement can be detected with these two methods in order to inform their usability according to the types of deformation. Therefore, this study conducted to investigate horizontal and vertical displacement monitoring performance and capability of determining the direction of displacements of both methods using a developed displacement simulator apparatus. For this purpose, 20 simulated displacement tests were handled. Besides the 24?h data sets, 12?h, 8?h, 4?h and 2?h subsets were considered to examine the influence of short time spans. Each data sets were processed using GAMIT/GLOBK and GIPSY/OASIS scientific software for relative and PPP applications respectively and derived displacements were compared to the simulated (true) displacements. Then statistical significance test was applied. Results of the experiment show that using 24?h data sets, relative method can determine up to 6.0?mm horizontal displacement and 12.3?mm vertical displacement, while PPP method can detect 8.1?mm and 19.2?mm displacements in horizontal and vertical directions respectively. Minimum detected displacements are found to grow larger as time spans are shortened.     

Modelling and simulation to support the design of a Dutch Protein Crystallization Facility.

This paper reports on the progress made in the development of the Netherlands Protein Crystallization Facility. The facility allows two crystallization techniques: Vapour diffusion and micro-dialysis. The design and development is accompanied by a project in which it tried to model and simulate the events which occur during the vapour diffusion process within the crystallization cell.