改善TiAl合金高温抗氧化性能的研究进展

综述了改善TiAl合金高温抗氧化性能的近期研究进展,着重介绍了合金元素对TiAl合金高温抗氧化性能的影响、表面改性及抗氧化涂层对改善其高温抗氧化性能的作用等.综合来看,通过合金化并结合先进的表面防护方法是改善TiAl合金800℃以上高温抗氧化性能的非常有效的途径.     

粉末冶金γ-TiAl系合金的性能及成形工艺

利用预合金球形粉末,制备了高性能的粉末冶金TiAl系合金材料,对其性能和微观组织做了测试和分析,并介绍了粉末冶金γ-TiAl系合金的钎焊工艺和研制的部分典型样件.研究结果发现:粉末冶金TiAl系合金具有较高的力学性能、细小的微观组织和优异的抗氧化性能,能够成为研制某些飞行器的备选材料.     

合金元素Y对高铌TiAl高温合金长期抗氧化性的影响

研究不同含Y量对高铌TiAl合金在900℃恒温条件下,1000h的抗氧化性的影响.结果发现,从长期看,氧化速率、氧化膜结构以及氧化膜抗剥落能力均与Y含量有关.在900℃等温氧化条件下,0.4 at%Y含量能有效提高高铌TiAl合金的抗氧化性,而高Y含量对与抗氧化性的负面影响在氧化初始阶段已经十分明显.通过对氧化后样品SEM和EDS分析发现,适量Y元素的加入可以细化氧化物颗粒,促使合金表面形成连续Al2O3保护膜,提高氧化膜与合金基体的粘附性,从而提高高铌TiAl合金的高温长期抗氧化性.     

高能球磨与无压烧结制备高铌TiAl合金

以大粒度Ti-45Al-8.5Nb-0.2B-0.2W-0.1Y预合金粉末为原料,研究了高能球磨与无压烧结制备高铌TiAl合金工艺.结果表明高能球磨可显著改善合金粉末的压制性能,并对粉末的烧结致密化有促进作用;高能球磨60min的预合金粉末经过1500℃,2h无压烧结后,可获得高致密度、具有细小全层片组织的高铌TiAl合金,其抗压强度为3150MPa,相对压缩率为25.2%,显示出较好的室温压缩性能.     

粉末冶金酌-TiAl 系合金的性能及成形工艺

利用预合金球形粉末,制备了高性能的粉末冶金TiAl 系合金材料,对其性能和微观组织做了测试
和分析,并介绍了粉末冶金酌-TiAl 系合金的钎焊工艺和研制的部分典型样件。研究结果发现:粉末冶金TiAl 系
合金具有较高的力学性能、细小的微观组织和优异的抗氧化性能,能够成为研制某些飞行器的备选材料。     

真空吸铸TiAl基合金组织研究

利用金属型真空吸铸技术获得了TiAl基合金薄板件,并研究了该铸件的铸态组织以及合金元素对其组织的影响。实验结果表明:由于金属型的强制冷却作用,金属型真空吸铸的Ti-47Al合金薄板铸件铸态组织细小,平均晶粒尺寸在60μm左右;W元素的添加有利于B2相的形成,从而细化组织,其机理是B2相阻碍了α晶粒长大;Si元素添加生成的Ti5Si3相,主要分布在晶界处,形成的Ti5Si3第二相质点会阻碍TiAl基合金凝固过程中组织的长大,有利于细化TiAl基合金组织。     

TiAl/TiAl、TiAl/TC4真空电子束焊接头组织及缺陷分析

采用电子束焊接方法对航空航天用的新型结构材料TiAl合金的自体及与TC4的异体对接接头进行了焊接试验,并利用光学金相和元素能谱分析方法(EDS)对TiAl/TiAl及TiAl/TC4电子束焊接接头的组织结构和连接状况进行了研究.研究结果表明TiAl/TiAl的焊缝组织为铸态TiAl柱状晶组织,焊缝内部及熔合线热影响区附近有大量冷裂纹产生,接头强度恶化;过高的焊接速度及粗晶的TiAl母材是导致TiAl/TiAl接头中产生裂纹的主要原因;TiAl/TC4焊缝为近Ti3Al的支晶混合组织,因TiAl与TiAl相比具有较好的延塑性,从而使TiAl/TC4焊缝的抗裂性能提高,接头中未见有冷裂纹出现,这说明TiAl/TC4接头拥有比TiAl/TiAl接头更好的电子束焊接性.     

高铌钛铝合金的制备工艺

研究了高铌TiAl金属间化合物的材料制备工艺。结果表明,感应凝壳熔炼时的合金收得率远远小于自耗熔炼时的合金收得率,因此在熔炼过程中损失主要来自于感应熔炼过程,而感应熔炼过程中合金的损失主要来自于凝壳大小及合金熔液挥发的多少;高铌TiAl合金的成分波动主要是由于凝壳大小波动造成的,感应熔炼完成后合金的Al含量取决于凝壳和合金溶液挥发对合金Al含量的共同影响效果;高铌TiAl合金在熔炼过程中,Nb的含量是在逐渐增加的。经过1200℃,24小时均匀化退火可以消除原始铸态组织的枝晶偏析。     

高温TiAl合金热成形技术研究进展

γ-TiAl合金具有优异的高温性能,是航空发动机650~900℃服役温度区间的重要候选材料。在回顾TiAl合金发展过程与应用现状的基础上,主要介绍了TiAl合金铸锭熔炼、铸造、包套等温锻造、包套热挤压等热加工技术的研究进展,提出了TiAl合金低成本近净成形技术面临的机遇和挑战。     

基于最小加工表面裂纹的TiAl合金铣削参数优化

TiAl合金以其优异的性能被广泛应用于航空、航天制造领域,但由于TiAl合金自身的物理、化学特性,导致其切削性能较差,加工过程中容易出现工件表面烧伤、表面微裂纹等问题。为了研究TiAl合金铣削加工过程中切削工艺参数对加工表面裂纹的影响规律,设计了TiAl合金切削参数与加工表面裂纹之间的正交试验。结果表明:切削速度对TiAl合金铣削表面裂纹的影响最大,其次是切削深度和切削宽度,每齿进给量对表面裂纹的影响最小。基于遗传算法,以表面裂纹长度为目标函数,优化得到的最优参数组合为:ae=0. 2 mm、ap=0. 2003 mm/z、fz=0. 02001 mm/z、vc=20. 0004 m/min。采用优化后的参数铣削TiAl合金,发现工件表面的实际加工裂纹长度和经过算法优化的裂纹长度相差较小,该优化方法可行性较高,误差较小。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.