智能变形机翼无人机稳定与飞行控制研究

研究了采用分布式翼面变形装置替代操纵面的无人机稳定与飞行控制技术。针对智能材料制成的变形装置,确定了变形无人机的气动力计算模型,得到了控制效能系数;采用极点配置法设计了侧向控制系统,纵向控制系统的设计采用了PID控制。仿真结果验证了利用翼面变形装置替代操纵面进行稳定和机动的可行性。该项研究可为无人机的飞行控制设计提供理论参考。     

变体飞行器控制系统综述

介绍了变体飞行器控制系统和涉及的控制理论问题。分析了变体飞行器的控制系统,指出变体飞行器的控制系统由变形控制层和飞行控制层组成。对变体飞行器的硬件结构和变体飞行器控制方法的研究现状进行了阐述。分析了集中式和分布式两种变形机械结构以及控制系统体系结构,提出采用总线网络连接变形结构的分布式元件。总结了变体飞行器需深入研究的变形控制和飞行控制问题,包括大尺度变体飞行器的飞行控制问题,通信受约束的大数目的驱动器的协调控制问题。     

Gain self-scheduled H_∞ control for morphing aircraft in the wing transition process based on an LPV model

This article investigates gain self-scheduled H 1 robust control system design for a tailless fold- ing-wing morphing aircraft in the wing shape varying process. During the wing morphing phase, the aircraft’s dynamic response will be governed by time-varying aerodynamic forces and moments. Nonlinear dynamic equations of the morphing aircraft are linearized by using Jacobian linearization approach, and a linear parameter varying (LPV) model of the morphing aircraft in wing folding is obtained. A multi-loop controller for the morphing aircraft is formulated to guarantee stability for the wing shape transition process. The proposed controller uses a set of inner-loop gains to provide stability using classical techniques, whereas a gain self-scheduled H 1 outer-loop controller is devised to guarantee a specific level of robust stability and performance for the time-varying dynamics. The closed-loop simulations show that speed and altitude vary slightly during the whole wing folding process, and they converge rapidly after the process ends. This proves that the gain self-scheduled H 1 robust controller can guarantee a satisfactory dynamic performance for the morphing aircraft during the whole wing shape transition process. Finally, the flight control system’s robustness for the wing folding process is verified according to uncertainties of the aerodynamic parameters in the nonlinear model.     

折叠机翼变体飞机非对称变形控制效率分析

折叠机翼变体飞机变形量大,变形引起的气动参数变化显著,提出一种将非对称变形作为操纵输入的控制方案,研究非对称变形的控制效率和有效区间。首先建立能够完整描述变形过程的非线性动力学方程和气动力模型;然后基于非对称变形控制方法建立一种非对称变形操纵模型;最后通过与常规操纵面效率对比和仿真的动态响应总结出非对称变形操纵的最大变形操纵有效区间。结果表明:在较低飞行速度下非对称变形操纵效率高,非对称变形操纵能够在基准折叠角度90°附近提供最高的滚转操纵效率。     

Proportional fuzzy feed-forward architecture control validation by wind tunnel tests of a morphing wing

In aircraft wing design, engineers aim to provide the best possible aerodynamic performance under cruise flight conditions in terms of lift-to-drag ratio. Conventional control sur-faces such as flaps, ailerons, variable wing sweep and spoilers are used to trim the aircraft for other flight conditions. The appearance of the morphing wing concept launched a new challenge in the area of overall wing and aircraft performance improvement during different flight segments by locally altering the flow over the aircraft's wings. This paper describes the development and appli-cation of a control system for an actuation mechanism integrated in a new morphing wing structure. The controlled actuation system includes four similar miniature electromechanical actuators dis-posed in two parallel actuation lines. The experimental model of the morphing wing is based on a full-scale portion of an aircraft wing, which is equipped with an aileron. The upper surface of the wing is a flexible one, being closed to the wing tip; the flexible skin is made of light composite materials. The four actuators are controlled in unison to change the flexible upper surface to improve the flow quality on the upper surface by delaying or advancing the transition point from laminar to turbulent regime. The actuators transform the torque into vertical forces. Their bases are fixed on the wing ribs and their top link arms are attached to supporting plates fixed onto the flex-ible skin with screws. The actuators push or pull the flexible skin using the necessary torque until the desired vertical displacement of each actuator is achieved. The four vertical displacements of the actuators, correlated with the new shape of the wing, are provided by a database obtained through a preliminary aerodynamic optimization for specific flight conditions. The control system is designed to control the positions of the actuators in real time in order to obtain and to maintain the desired shape of the wing for a specified flight condition. The feasibility and effectiveness of the developed control system by use of a proportional fuzzy feed-forward methodology are demon-strated experimentally through bench and wind tunnel tests of the morphing wing model.     

Continuous morphing trailing-edge wing concept based on multi-stable nanomaterial

Morphing technology is one of the most effective methods to improve the flight efficiency of aircraft. Traditional control surfaces based morphing method is mature and widely used on current civil and military aircraft, but insufficiently effective for the entire flight envelope. Recent research on morphing wing still faces the challenge that the skin material for morphing should be both deformable and stiff. In this study, a continuous morphing trailing-edge wing with a new multi-stable nano skin material fabricated using surface mechanical attrition treatment technology was proposed and designed. Computational fluid dynamics simulation was used to study the aerodynamic performance of the continuous morphing trailing-edge wing. Results show that the lift coefficient increases with the increase of deflection angle and so does the lift-drag ratio at a small angle of attack. More importantly, compared with the wing using flaps, the continuous morphing trailing-edge wing can reduce drag during the morphing process and its overall aerodynamic performance is improved at a large angle of attack range. Flow field analysis reveals that the continuous morphing method can delay flow separation in some situations.     

主动变形扑翼飞行器的设计和风洞测力试验研究

主动变形扑翼可以模仿鸟翼飞行时的复杂运动。为了了解主动变形扑翼飞行器的气动特性,在研究鸟类骨骼结构和翅膀及尾翼运动规律的基础上,设计并制造了一种基于机器人技术的主动变形扑翼飞行器;给出了主动变形扑翼飞行器的机构运动规律函数,并设计出机构运动控制系统;在低速风洞中对此飞行器进行了一系列测力试验,研究了主动变形扑翼的升力、推力特性,以及风速、扑动频率、扑动幅度、伸展相位等参数对升力和推力的影响,并与常规扑翼进行了对比分析。试验结果表明,较之常规扑翼,主动变形扑翼可以显著增加升力和增强对不同飞行状态的适应能力。     

变体飞机设计的主要关键技术

针对变体飞机的特点,分析了其在设计中出现的诸多新的技术难点,对拟解决的主要关键技术,包括变体飞机不同于常规固定构型飞机的总体及气动协调设计、机翼智能结构设计、可控性设计与飞行控制系统设计等进行了详细介绍。研究结果对于变体飞机的设计具有一定参考价值。     

Design and experimental testing of a control system for a morphing wing model actuated with miniature BLDC motors

The paper deals with the design and experimental validation of the actuation mechanism control system for a morphing wing model. The experimental morphable wing model manufactured in this project is a full-size scale wing tip for a real aircraft equipped with an aileron. The morphing actuation of the model is based on a mechanism with four similar in house designed and manufactured actuators, positioned inside the wing on two parallel lines. Each of the four actuators used a BrushLess Direct Current (BLDC) electric motor integrated with a mechanical part performing the conversion of the angular displacements into linear displacements. The following have been chosen as successive steps in the design of the actuator control system: (A) Mathematical and software modelling of the actuator; (B) Design of the control system architecture and tuning using Internal Model Control (IMC) methodology; (C) Numerical simulation of the controlled actuator and its testing on bench and wind tunnel. The morphing wing experimental model is tested both at the laboratory level, with no airflow, to evaluate the components integration and the whole system functioning, but also in the wind tunnel, in the presence of airflow, to evaluate its behavior and the aerodynamic gain.     

Distributed fixed-time attitude coordinated control for multiple spacecraft with actuator saturation

This paper investigates the distributed fixed-time attitude coordinated control problem for multiple spacecraft subject to actuator saturation under the directed topology. First, a distributed fixed-time observer is presented for each follower spacecraft to estimate the leader spacecraft’s states. Compared with the commonly used fixed-time observer, the settling time of the proposed fixed-time observer can be easily adjusted by some free design parameters. Next, a distributed fixed-time control ...     

基于逆向有限元法的变形机翼鱼骨的变形重构

变形监测技术能够为自适应变形机翼的变形控制系统提供参考信息，是保证结构安全性以及优化结构的运行性能的重要手段。传统的基于光学成像的变形测量方法已经不能满足自适应智能结构的实时变形监测的要求。由于变形机翼表面受气动载荷影响，不便于直接在变形机翼蒙皮表面布置应变传感系统，目前还没有针对鱼骨结构这种真实复杂机翼结构的变形重构研究，大多针对机翼翼型的变形重构研究是将整个机翼简化成简单的翼形板、梁结构。针对上述问题，本文首次以真实复杂变形机翼主承力结构——鱼骨为研究对象，提出了一种基于逆向有限元（iFEM）算法与位移分段叠加思想结合的变形监测方法，根据Mindlin板变形理论建立四节点逆向壳单元，采用应变传感系统测得鱼骨结构表面应变分布作为算法输入，然后基于最小二乘变分方程求解结构应变场和位移场之间的传递函数，重构鱼骨结构的变形形状，为反演机翼翼型的变形形状提供方法。针对真实自适应变形机翼的主要承力构件开展了变形实验，实验结果表明，机翼鱼骨在分别偏转5°、10°、15°的情况下，逆向有限元法能准确重构鱼骨变形形状，验证了基于逆向有限元法的变形重构方法在真实自适应变形机翼结构变形重构研究中的有效性和准确性。     

Integrated method of guidance,control and morphing for hypersonic morphing vehicle in glide phase

The morphing technology of hypersonic vehicle improved the flight performance by changing aerodynamic characteristics with shape deformations, but the design of guidance and control system with morphing laws remained to be explored. An Integrated of Guidance, Control and Morphing (IGCM) method for Hypersonic Morphing Vehicle (HMV) was developed in this paper. The IGCM method contributed to an effective solution of morphing characteristic to improve flight performance and reject the disturbance for guidance and control system caused by the morphing system for HMV in gliding phase. The IGCM models were established based on the motion models and aerodynamic models of the variable span vehicle. Then the IGCM method was designed by adaptive block dynamic surface back-stepping method with stability proof. The parallel controlled simulations’ results showed the effectiveness in accomplishing the flight mission of IGCM method in glide phase with smaller terminal errors. The velocity loss of HMV was reduced by 32.8% which inferred less flight time and larger terminal flight velocity than invariable span vehicle. Under the condition of large deviations of aerodynamic parameters and atmospheric density, the robustness of IGCM method with variable span was verified.     

Design,modeling, and control of morphing aircraft:A review

A morphing aircraft can adapt its configuration to suit different types of tasks, which is also an important requirement of Unmanned Aerial Vehicles(UAV). The successful development of an unmanned morphing aircraft involves three steps that determine its ability and intelligent: configuration design, dynamic modeling and flight control. This study conducts a comprehensive survey of morphing aircraft. First, the methods to design the configuration of a morphing aircraft are presented and analyzed...     

Nonlinear hysteresis identification and compensation based on the discrete Preisach model of an aircraft morphing wing device manipulated by an SMA actuator

The conception of aircraft morphing wings thrives in aeronautics since the appearance of shape memory alloys(SMAs). An aircraft morphing wing device, manipulated by an SMA actuator, inherits the intrinsic nonlinear hysteresis from the SMA actuator, ending up with control disadvantages. Conventionally, systems with SMA actuators are constrained to bi-stable states to bypass the hysteresis region. Rather than retreating a morphing wing device to bi-stable states, this paper is dedicated to transcend the morphing wing device beyond the customary limit. A methodology of discrete Preisach modeling, which identifies the hysteresis of the morphing wing device, is proposed herein. An array of discrete equal-distance points is applied to the Preisach plane in order to derive the Preisach density over the partitioned unit of the Preisach plane. Discrete Preisach modeling is fulfilled by the discrete first-order reversible curve(DFORC). By utilizing the discrete Preisach model, the aircraft morphing wing device is simulated; the validity and accuracy of discrete Preisach modeling are demonstrated by contrasting the simulated outcome with experimental data of the major hysteretic loop and the wingspan-wise displacement over time; a comparison between simulation and experimental results exhibits consistency. Afterwards, a hysteresis compensation strategy put forward in this paper is implemented for quasi-linear control of the aircraft morphing wing device, which manifests a compensated shrinking hysteresis loop and attains the initiative of extending the morphing range to the intrinsic hysteretic region.     

变形飞机机翼折叠机构设计及折叠角度测量

针对变形飞机机翼变形机构的设计要求,设计由舵机、蜗轮蜗杆机构、平行四边形机构组合而成的机翼变形机构,并设计基于三轴加速度计和DSP处理器的机翼折叠角度的测量算法和控制系统。利用加速度计分别求得机身和机翼相对于参考坐标系的角度,相减即得机身平面与机翼的夹角,制作一架小型折叠翼飞机模型对测量算法进行验证。结果表明：机翼能够稳定折叠在任一给定角度,测量算法准确,机翼实际折叠角度误差在可接受的范围内。     

Transient aeroelastic responses and flutter analysis of a variable-span wing during the morphing process

To investigate the transient aeroelastic responses and flutter characteristics of a variablespan wing during the morphing process,a novel frst-order state-space aeroelastic model is proposed.The time-varying structural model of the morphing wing is established based on the Euler-Bernoulli beam theory with time-dependent boundary conditions.A nondimensionalization method is used to translate the time-dependent boundary conditions to be time-independent.The time-domain aerodynamic forces are calculated by the reduced-order unsteady vortex lattice method.The morphing parameters,i.e.,wing span length and morphing speed,are of particular interest for understanding the fundamental aeroelastic behavior of variable-span wings.A test case is proposed and numerical results indicate that the flutter characteristics are sensitive to both of the two morphing parameters.It could be noticed that the aeroelastic characteristics during the wing extracting process are more serious than those during the extending process at the same morphing speed by transient aeroelastic response analysis.In addition,a faster morphing process can get better aeroelastic performance while the mechanism comlexity will arise.     

A new non-linear vortex lattice method:Applications to wing aerodynamic optimizations

This paper presents a new non-linear formulation of the classical Vortex Lattice Method (VLM) approach for calculating the aerodynamic properties of lifting surfaces. The method accounts for the effects of viscosity, and due to its low computational cost, it represents a very good tool to perform rapid and accurate wing design and optimization procedures. The mathematical model is constructed by using two-dimensional viscous analyses of the wing span-wise sections, according to strip theory, and then coupling the strip viscous forces with the forces generated by the vortex rings distributed on the wing camber surface, calculated with a fully three-dimensional vortex lifting law. The numerical results obtained with the proposed method are validated with experimental data and show good agreement in predicting both the lift and pitching moment, as well as in predicting the wing drag. The method is applied to modifying the wing of an Unmanned Aerial System to increase its aerodynamic efficiency and to calculate the drag reductions obtained by an upper surface morphing technique for an adaptable regional aircraft wing.     

A compliant polymorphing wing for small UAVs

This paper presents the development of a novel compliant polymorphing wing capable of chord and camber morphing for small UAVs. The morphing wing can achieve up to 10% chord extension and ±20° camber changes. The design, modeling, sizing, manufacturing and mechanical testing of the wing are detailed. The polymorphing wing consists of one continuous front spar fixed to the fuselage and a rear spar on each side of the wing. Each rear spar can translate in the chordwise direction (chord morphing) and rotate around itself (camber morphing). A flexible elastomeric latex sheet is used as the skin to cover the wing and maintain its aerodynamic shape whilst allowing morphing. The loads from the skin are transferred to the spars using the compliant cellular ribs that support the flexible skin and facilitate morphing. Pre-tensioning is applied to the skin to minimize wrinkling when subject to aerodynamic and actuation loads. A rack and pinion actuation system, powered by stepper motors, is used for morphing. Aero-structural design, analysis and sizing are conducted. Performance comparison between the polymorphing wing and the baseline wing (non-morphing) shows that chord morphing improves aerodynamic efficiency at low angles of attack while camber morphing improves efficiency at high angles of attack.     

压电驱动器的气动弹性应用

 随着压电智能材料与结构的发展,压电驱动器在气动弹性控制领域占据重要地位。使用压电驱动器控制翼面变形,利用而不是抵抗气动弹性效应可以控制升力、力矩以及它们的分布。采用基本相同的智能结构翼面控制系统,根据不同的控制目标需求,使用压电智能材料驱动器可以达到多种目的,包括静态的形状控制与动态的颤振抑制、抖振控制与阵风响应控制。静态控制方面例如改变翼面形状获得附加空气动力以增加升力、提供横滚力矩、改变升力分布以减小诱导阻力或减小翼根弯矩等;动态控制例如利用改变翼面形状产生的附加空气动力作为控制载荷,改变气动弹性系统的耦合程度,根据控制效果要求可作为气动阻尼、气动刚度或气动质量。这种控制方法可以减轻结构重量,提高操纵效率,扩大飞行包线,提高材料利用率,已成为可变形飞行器的重要研究内容。本文主要阐述压电驱动器气动弹性应用的动机与机理、发展与成就以及问题与展望。     

折叠机翼变体飞机纵向操纵性与稳定性研究

针对一种飞翼布局折叠机翼变体飞机方案,建立了相应的研究模型,使用涡格估算方法计算出机翼折叠角度对全机纵向静稳定性的影响.利用飞机纵向小扰动运动方程,分别得到了机翼展开和折叠状态的长、短周期模态,并对其动稳定性进行了讨论.结合工程估算方法和风洞试验方法,计算出内段机翼折叠过程全机力矩系数、升降舵操纵导数以及升降舵配平偏角...